DOWNLOAD Sony KV-BM212M10 Service Manual ↓ Size: 5.67 MB | Pages: 59 in PDF or view online for FREE

– 9 –

R G

B

R

G

B

R

G B

R

B

R

G

G

G

B

R

B

• Before starting this adjustment, adjust the focus,

horizontal size and vertical size.

• Receive dot/hatch signal.
• Pic mode: Standard.

1. (Moving vertically), adjust the V.STAT magnet so that

the red, green and blue dots are on top of each other
at the center of the screen.

2. (Moving horizontally), adjust the H.STAT control so

that the red, green and blue dots are on top of each
other at the center of the screen.

3. If the H.STAT variable resistor cannot bring the red,

green and blue dots together at the center of the
screen, adjust the horizontal convergence with the
H.STAT variable resistor and the V.STAT magnet in
the manner given below.
(In this case, the H.STAT variable resistor and the
V.STAT magnet influence each other, so be sure to
perform adjustments while tracking.)

Center dot

R    G    B

R

G

B

H. STAT VR

V. STAT

Magnet

RV750
H. STAT

C Board

BMC (Hexapole)

V.STAT

DY pocket

Purity

V.STAT

BMC

Purity

Operation of V.STAT magnet
If the V.Stat magnet is moved in the “A” and “B” arrows,
the red, green and blue dots moves as shown below.

Moved RV750 H.STAT.
the red, green and blue dots move as shown below.

4. BMC (Hexapole) Magnet.

If the red, green and blue dots are not balanced or
aligned, then use the BMC magnet to adjust in the
manner described below.

R

R

G

G

B

B

A

B

B

A

R

R

G

G

B

B

A

B

– 10 –

Preparation:
• Before starting this adjustment, adjust the horizontal

static convergence and the vertical static
convergence

TLV

R B

YCH

R

B

XCV

B

R

TLH

B

R

Piece A (90), conv. correct

a

b

c

d

TLH

Insert

TLH

Correction Plate to DY Pocket

(Left or Right)

YCH

Insert

YCH

VOL on DY

TLV

Rotate TLV

VOL on DY

XCV

Rotate XCV

Adj core on DY

1. Affix a Piece A (90), conv. correct corresponding to

the misconverged areas.

b

a

c

d

a-d : screen-corner
        misconvergence

ON DY:

TLV

TLV

XCV

YCH

DY pocket

DY pocket

TLH Plate

XCV

– 11 –

1. Set to Service Mode (Refer Section 3-1:

ADJUSTMENTS WITH COMMANDER)

2. Input white raster signal.
3. Set Picture to <DYNAMIC mode>.
4. Select RDRV (002) with 

1

 and 

4

 and fixed the

value to 37 (Dec) with 

3

 and 

6

.

5. Adjust WHBL GDRV (003) and BDRV (004) with 

1

and 

4

 and adjust the data with 

3

 and 

6

 for best

white balance in Highlight condition.

6. Write into the memory by pressing [MUTING] then 

-

.

7. Adjust WHBL BKOR (000) and BKOG (001) with 

1

and 

4

 and adjust the level with 

3

 and 

6

 for best

white balance cut-off condition.

8. Write into memory by pressing [MUTING] then 

-

.

9. US model need to apply only for colour temperature

in Neutral.

1. Set to service mode.
2. Brightness set to 50%, Picture....Minimum
3. Select WHBL SBRT (010) with 

1

 and 

4

 and adjust

SBRT (010) data with 

3

 and 

6

 so that the third

stripe from right dimly lit.

4. Write into the memory by pressing [MUTING] then 

-

.

5. GA models C/O: 20 IRE

S/G: 30 IRE

165 

± 2VDC

FOCUS adjustment should be completed before the W/B
adjustment:
1. Receive digital monoscope pattern.
2. Set picture mode: DYNAMIC.
3. Adjust focus VR to obtain a just focus at the center of

the screen.

4. Change receiving signal to white pattern and blue

back.

5. Confirm MAGENTA RING is not noticeable. Incase

magenta ring is obvious, then adjust FOCUS VR to
balance magenta ring and FOCUS.

1. Set the PICTURE & BRIGHTNESS to STANDARD.
2. Put the Video input mode signal.
3. Connect R,G,B of the C board cathode to

oscilloscope.

4. Adjust Brightness to obtain the cathode value to

value below.

5. Adjust G2 (screen) on the FBT until picture shows

the point before cut off.

SCREEN

FOCUS

– 12 –

Service adjustments to this model can be performed using the supplied remote commander RM-W101.

With the unit on standby

This operation sequence puts the unit into service mode.
This screen display is:

Set the standby condition (Press [POWER] button on the commander), then press [POWER] button again, hereupon it
becomes TV mode.

1. Set to Service Mode.
2. Press 1 (UP) and 4 (DOWN), to select the adjustment item.
3. Change item by pressing 3, 6.
4. Press [MUTING] button to indicate WRITE on the screen.
5. Press - button to write into memory.

1. After adjustment, pull out the plug from AC outlet, and then plug into AC outlet again.
2. Turn the power switch ON and set to Service Mode.

  

t [DISPLAY] t 5 t [VOL $+% ] t [POWER]

item no.

service data

NVM

field

channel no./

category

in decimal

item name

in decimal

NG

service command

frequency

video input name

GEOM

006

HSIZ

031

x

SERVICE

60

S VIDEO 1

software

service data

reserved

power on time

release ID

version

in binary

for factory

color system

(decimal)

SUS01

0.69U

0001 1111

FF FF

NTSC3

65535

Status Byte

Status Byte

Flash DCXO

#1 SSD

#2 SSD

111 11 11 1 7 11

FG

xy 111

000000

000000

VDSP_C Flag

CO_LOCKED

VDSP

Detected Stereo Type (Direct Value from CZ_ Stereo_Mode)

S : for Sony
A : Aiwa

U S

: US/Latin/Taiwan

E U

: Europe

G A

: General Area

J P

: Japan

0 1 : serial no. of the M/P release

for each destination

111

Needed for Nicam DCXO aligment Purpose

xy

Value of x = 0 - Unknown, 1 - BTSC, 2 - A2, 3 - NICAM,
4 - KOREAN, 5 - Japan, 6 - AV Stereo
Value of y = 0 - Mono, 1 - Stereo, 2 - Bilingual, 4 - SAP/Single

1, 4

Select the adjustment item.

r

3, 6

Raise/lower the data value.

r

[MUTING]

Writes.

r

-

Executes the writing.