DOWNLOAD Sony KV-AW21M50 (serv.man3) Service Manual ↓ Size: 10.33 MB | Pages: 84 in PDF or view online for FREE

– 7 –

The following adjustments should be made when a complete
realignment is required or a new picture tube is installed.

The controls and switch should be set as follows unless
otherwise noted:

Picture control ......................................................... NORMAL
Brightness control ................................................... NORMAL

Perform the adjustments in order as follows:
1. Beam Landing
2. Convergence
3. Focus
4. G2 (SCREEN)
5. White Balance

Note: Test Equipment Required
1. Pattern Generator
2. Degausser
3. DC Power Supply
4. Digital Multimeter

Preparation :
• Feed in the white pattern signal.

• Before starting, degauss the entire screen with the

degausser.

• In order to reduce the geomagnetism on the set's

picture tube, face it east or west.

1. Input a raster signal with the pattern generator.
2. Loosen the deflection yoke mounting screw, and set the

purity control to the center as shown below.

3. Set the raster signal of the pattern generator to green.
4. Move the deflection yoke (DY) backward and adjust the

purity control so that green is in the center and blue and
red are at the sides evenly.

5. Then move the DY forward and adjust so that the entire

screen becomes green.

6. Now switch over raster signal to red then blue and

confirm the condition.

...................................................................................................................................................................................................................... ...........

5. Oscilloscope
6. Landing Checker
7. XCV Adjuster

Purity control

Red

Blue

Green

7. When the position of the DY is determined, tighten it

with the DY mounting screw.

8. If the beam does not land correctly in all corners of the

screen, use magnet disc to correct it.

Preparation :
• Before starting, perform FOCUS adjustment.

• Picture mode STANDARD.

• Receive dot/cross hatch pattern.

a

b

b

c

c

d

d

a

Purity control
corrects this area.

Disc magnets or rotatable
disc magnets correct these
areas (a-d).

Deflection yoke positioning
corrects these areas.

4 pole magnet

RV705
H. STAT

RV1800
G2 (SCREEN) 

Center dot

R     G     B

G

R

B

– 8 –

1. (Moving vertically), adjust the 4 pole magnet to converge

red, green and blue dots in the center of the screen.

2. Tilt the 4 pole magnet and adjust static convergence to

open or close the 4 pole magnet.

3. When the 4 pole magnet is moved in the direction of

arrow A and B, the red, green and blue dots moves as
shown below:

If the blue dots does not converge with the red and green
dots, use the 6 pole magnet to adjust in the manner
described below.

R

R

G

G

B

B

A

B

B

A

R G

B

R

G

B

R

G B

R

B

R

G

G

G

B

R

B

6 Pole Magnet

4 pole Magnet

DY pocket

Purity

6 Pole

Magnet

4 Pole

Magnet

Preparation :
• Before starting this adjustment, adjust the horizontal

and vertical static convergence.

Input cross hatch pattern.
i)

TLH
Adjust the horizontal convergence of red and blue dots
by inserting TLH Correction Plate to the DY pocket (left
or right).

ii) YCH

Adjust YCH to balance Y axis.

iii) TLV

Adjust the vertical convergence of red and blue dots.

iv) XCV

Adjust XCV to balance X-axis.

Affix a Piece A (90), Convergence Correct/Permaloy Assy
Correction to the misconverged areas.

TLV

R B

YCH

R

B

XCV

B

R

TLH

B

R

(VR1)
TLV1 (no need to adjust)

DY pocket

DY pocket

TLH Plate

(VR3)

TLV2

(XCV)

(VR2)

YCH

ON DY:

b

a

c

d

a-d : screen-corner
        misconvergence

a1

b1

c1

d1

a1~d1: Piece A (90), Convergence Correct

or

Permaloy Assy Correction

B

R

G

G

R

B

– 9 –

FOCUS adjustment should be completed before W/B
adjustment.

1. Receive digital monoscope pattern.
2. Set Picture Mode to "DYNAMIC".
3. Adjust focus VR to obtain a just focus at the center of

the screen.

4. Change the receiving signal to white pattern and blue

back.

5. Confirm magenta ring is not noticeable. In case magenta

ring is obvious, then adjust FOCUS VR to balance
magenta ring and FOCUS.

1. Set the following condition:

– Picture and Brightness to "STANDARD".
– TV to Video mode.
– WHBL 016 "RGBB" to 01

2. Connect R, G, B of the C/CV board cathode to

oscilloscope.

3. Adjust Brightness to obtain the cathode value to the

value stated below.

4. Adjust SCREEN VR on the FBT until the scanning line

disappears.

5. Finally set WHBL 16 "RGBB" back to 00.

165 

± 2VDC

1. Set to Service Mode.
2. Input white raster signal using signal generator.
3. Set the following condition:

Picture "DYNAMIC", PICT 006 "WTS" to 00.

4. At Highlight condition, select WHBL 03 "GDRV" and 04

"BDRV" with 1 and 4 button of the remote
commander then adjust the data with 3 and 6 button.

5. At Cutoff, select WHBL 000 "BKOR" and 001 "BKOG"

and adjust the data.

6. Perform adjustment at Highlight and Cutoff condition

until it reaches its target.

7. Write data into memory by pressing [MUTING] t -.
8. Finally set PICT 006 "WTS" back to its original data.

VIVID : 45000K+SMPCD
Center data:

X : 0.2444
Y : 0.2446

– 10 –

Service adjustments to this model can be performed using the supplied remote commander RM-GA002.

With the unit on standby

This operation sequence puts the unit into service mode.
This screen display is:

Set the standby condition (Press [POWER] button on the commander), then press [POWER] button again, hereupon it becomes
TV mode.

1. Set to Service Mode.
2. Press 1 (UP) and 4 (DOWN), to select the adjustment item.
3. Change item by pressing 3, 6.
4. Press [MUTING] button to indicate WRITE on the screen.
5. Press - button to write into memory.

1. After adjustment, pull out the plug from AC outlet, and then plug into AC outlet again.
2. Turn the power switch ON and set to Service Mode.
3. Call the adjusted items again to confirm adjustments were made.

  t [DISPLAY] t 5 t [VOL $+% ] t [POWER]

item no.

service data

NVM

field

channel no./

category

in decimal

item name

in decimal

NG

service command

frequency

video input name

GEOM

006

HSIZ

031

x

SERVICE

60

S VIDEO 1

software

service data

reserved

power on time

release ID

version

in binary

for factory

color system

(decimal)

SUS01

0.69U

0001 1111

FF FF

NTSC3

65535

Status Byte

Status Byte

Flash DCXO

#1 SSD

#2 SSD

111 11 11 1 7 11

FG

xy 111

000000

000000

VDSP_C Flag

CO_LOCKED

VDSP

Detected Stereo Type (Direct Value from CZ_ Stereo_Mode)

S : for Sony
A : Aiwa

U S

: US/Latin/Taiwan

E U

: Europe

G A

: General Area

J P

: Japan

0 1 : serial no. of the M/P release

for each destination

111

Needed for Nicam DCXO aligment Purpose

xy

Value of x = 0 - Unknown, 1 - BTSC, 2 - A2, 3 - NICAM,
4 - KOREAN, 5 - Japan, 6 - AV Stereo
Value of y = 0 - Mono, 1 - Stereo, 2 - Bilingual, 4 - SAP/Single

1

, 4

Select the adjustment item.

r

3

, 6

Raise/lower the data value.

r

[MUTING]

Writes.

r

-

Executes the writing.