DOWNLOAD Sony KV-AR29M80A Service Manual ↓ Size: 9.93 MB | Pages: 94 in PDF or view online for FREE

– 5 –

Since the diagnostic results displayed on the screen are not automatically cleared, always check the self-diagnostic screen
during repairs. When you have completed the repairs, clear the result display to “0”.

Unless the result display is cleared to “0”, the self-diagnostic function will not be able to detect subsequent faults after
completion of the repairs.

[Clearing the result display]
To clear the result display to “0”, press buttons on the remote commander sequentially as shown below when the diagnostic
screen is being displayed.

Channel [8]

/ 0

[Quitting Self-diagnostic screen]
To quit the entire self-diagnostic screen, turn off the power switch on the remote commander or the main unit.

[+B overcurrent  OCP]

Occurs when an overcurrent on the +B(135) line is detected by Q604. If Q604 go to ON
and the voltage to pin 18 of IC301 should go down when V.SYNC is more than seven
verticals in a period, the unit will automatically turn off.

[Vertical deflection stopped]

Occurs when an absence of the vertical deflection pulse is detected by Q509 and IC001
shut down the power supply.

[Vertical deflection overcurrent]

Occurs when an overcurrent on V drive line is detected by Q507. Power supply will be
shut down when detect this by IC001.

[White balance failure]

If the RGB levels* do not balance or become low level within 5 seconds, this error will be
detected by IC301. TV will stay on, but there will be no picture.

* (Refers to the RGB levels of the AKB detection Ref pulse that detects IK.)

IC301

Y/CHROMA JUNGLE

FROM

CRT

[V] Q509/507

IC001

SYSTEM

IC003

MEMORY

IK-IN

MP/
PROTECT

O-LED

IO-8DAT

B-DAT

IO-SDAT

5

21

18

51

46

SDA 35

FROM
[+B] Q604 C6

45

– 6 –

Tweeter
Speaker
(Not used 
for this 
model)

1 Nine screws

(BVTP 4 

× 16)

2 Rear cover   

Tweeter
Speaker
(Not used 
for this model)

1 Two screws

(BVTP 4 

× 16)

2 Two screws

(Washer head)
(+P 4 

× 16)

1 Two screws

(BVTP 4 

× 16)

Tweeter Speaker
(Not used for this model)

Tweeter
Speaker
(Not used 
for this model)

3 J Board

4 Two screws
     (+BVTP 3 

× 12)

5 Terminal bracket

2 Two screws
     (+BVTP 3 

× 12)

1 One screw
     (+BVTP 4 

× 16)

6 Two Hooks

1 One Hook

2 D3 Board

– 7 –

• Please make sure the TV set is not in standing position before removing necessary CRT support located on bottom

right and left.

1) Place the TV set with the CRT face down on a cushion jig.
2) Removal the rear cover.
3) Removal the Speaker Block Assy.

5 Cover, H

6 H2 Board

4 Two hooks

2 Four hooks

3 H1 Board

1 One screw (Washer head)
     (+) BVTAP (3 x 12)

5 A Board

4 B9 Board

1 One screw

(Washer head)
(+) BVTAP (3 x 12)

2 One screw

(Washer head)
(+) BVTAP (3 x 12)

3 Two screws

(Washer head)
(+) BVTAP (3 x 12)

Tweeter Speaker
(Not used 
for this model) 

qs

 Earth Coating Assy

!∞ Block Center

4 Anode Cap Removal

!£ Band, DGC Removal

!§ Degaussing Coil

5 C6 Board Removal

9 Chassis Assy Removal

7 VM1 Board Removal

0 Support, CRT(2) Removal

qa

 Spring Tension(2) Removal

!¢ Holder, DGC(2) Removal

!¶ Nut, Special, CRT (4)

6 Loosen the Neck Assembly

fixing screw and removal

8 Loosen the Deflection Yoke

fixing screw and remove

– 8 –

• After removing the anode, short circuit the anode of the picture tube and the anode cap to the metal chassis, CRT

shield or carbon paint on the CRT.

• REMOVING PROCEDURES

1 Turn up one side of the rubber cap in the direction

a.

2 Using a thumb pull up the rubber cap firmly in the direc-

b.

3 When one side of the rubber cap is separated from the

c.

• HOW TO HANDLE AN ANODE-CAP

1 Do not damage the surface of anode-caps with

2 Do not press the rubber too hard so as not to

3 Do not turn the foot of rubber over too hard.

a

a

b

b

c

anode button