Sony KV-AR29M31 Service Manual ▷ View online
– 23 –
KV-AR29M31
RM-995
ITEM INFORMATION
No. OPB0 OP1
No. OPB0 OP1
Item
KV-AR29M31
M
1
D/K
1
I
1
B/G
1
AR34/29*
1
SECAM
1
XTAL 3.58
1
XTAL 4.43
1
AV Input
00 = no AV Input
01 = 1 AV Input
10 = 2 AV Input
11 = 3 AV Input
DVD Input
Effective only when "AV Input" is set to 3 AV Input
PIP 4
PIP 4
0 = disabled,
1 = enabled
No. OPB1 OP2
Item
KV-AR29M31
1
1
DVD Input
1
PIP 4
1
Thai Bil
0
HDEV
1
NICAM
1
AV Input
TOP
1
Initial Menu
Initial Menu Setup
0 = disabled,
1 = enabled
AP2
Auto Processor Selection
0 = AP, 1 = AP2.
Auto PIC
*3
Auto Picture Improvement
0 = off
PNC1/PNC2
1 = activate
PNC1/PNC2
A-TVsys
Auto TV System in Auto Program0 = disabled, 1 = enabled
US ST
*
USA Stereo
0 = disabled,
1 = enabled
DTE
DTE Model Selection
0 = Non DTE,
1 = DTE
Forced 50/60
Forced to 50/60 Hz during no signal condition 0=60Hz, 1=50Hz
Color SW
*2
Color Data Selection in Dynamic Mode
0 = 65 (No PIP), 1 = 57 (PIP)
Note:
*1
- For XA21/XH29 Models Only
*2
- For XA34/29/25 Models Only
*3
- For PNC3, the enables are from service item APG and APB.
No. OPB2 OP3
Item
KV-AR29M31
Colour SW*
2
1
Forced 50/60
0
DTE
1
US ST
0
A-TVsys
1
Auto PIC
1
AP2
1
Initial menu
1
APPLICABLE TO XS ONLY - Sub Language Selection (Bit 0 - Bit 2)
Korean Stereo*
Korean Stereo
0 = disabled,
1 = enabled
PNC2*
2
Enable switch of PNC2
0 = disable,
1 = enable
Video NTSC3.58*
Video Color System
0 = Multi System,
1 = Single System (NTSC3.58)
Wide
Enable wide mode
0 = disable,
1 = enable
Note : *APPLICABLE FOR NTSC MODELS ONLY
No. OPB3 *OP4
Item
KV-AR29M31
Thai/Korean
1
Arabic/C.Chinese
1
Chinese(multi mdl)
1
Video3
0
Vid NTSC3.58
0
Korean ST
0
PNC2
0
Wide
0
(APPLICABLE FOR XF-L(21" & 14") MODELS ONLY.
AR34/29*
SHG Offset in YCT
0 = AR29/25
1 = AR34
– 24 –
KV-AR29M31
RM-995
4-3. ADJUSTMENT FOR NON DIGITAL TEXTURE
ENHANCER (DTE) MODEL
(not used for this model)
SUB COLOR ADJUSTMENT
1. Select Video.
2. Input PAL Color Bar
3. Set to following condition PICTURE 100%, BRIGHTNESS
2. Input PAL Color Bar
3. Set to following condition PICTURE 100%, BRIGHTNESS
50%, Color 50%.
4. Connect an oscilloscope to pin
1 (BOUT) of CN305, A Board.
5. Set the service mode and select SAJ 3 ‘SCL’ with 1 and 4 of
the commander then adjust the VB2=VB3=VB4 3 and 6.
6. Press
[MUTING]
→ - of the commander to write the data.
7. Input NTSC Color Bar to set and repeat items (3 to 7).
8. Select "WIDE" mode, write the "SAME DATA- 3 STEPS" for
8. Select "WIDE" mode, write the "SAME DATA- 3 STEPS" for
both PAL and NTSC Color Bar input.
SUB COLOR ADJUSTMENT
1. Select Video.
2. Input PAL Color Bar
3. Set to following condition PICTURE 100%, BRIGHTNESS
2. Input PAL Color Bar
3. Set to following condition PICTURE 100%, BRIGHTNESS
50%, Color 50%.
4. Connect an oscilloscope to pin
1 (BOUT) of CN305, A Board.
5. Set the service mode and select SAJ 3 ‘SCL’ with 1 and 4 of
the commander then adjust the VB2=VB3=VB4 3 and 6.
6. Press
[MUTING]
→ - of the commander to write the data.
7. Add 6 steps and save the data.
8. Input NTSC Color Bar to TV set and repeat items 3 to 7.
9. Select "WIDE" mode, write the "SAME DATA- 3 STEPS" for
8. Input NTSC Color Bar to TV set and repeat items 3 to 7.
9. Select "WIDE" mode, write the "SAME DATA- 3 STEPS" for
both PAL and NTSC Color Bar input.
SUB HUE ADJUSTMENT
1. Select Video 1.
2. Input a NTSC 3.58 color-bar, video into Video 1.
3. Set the following condition:
2. Input a NTSC 3.58 color-bar, video into Video 1.
3. Set the following condition:
PICTURE 100%, BRIGHTNESS 50%, COLOR 50%
4. Connect an oscilloscope to pin
1 (B OUT) of CN305, A board.
5. Select SAJ 1 "SHU" with 1 and 4 of the commander by
setting to Service Mode and adjust to VB1=VB2=VB3=VB4
with 3 and 6.
with 3 and 6.
6. Press
[MUTING]
→ - of the commander to write the data.
7. Adjust SAJ 1 "SHU" as step 3 to 6 when receiving TV mode.
VB1
VB2
VB3
VB4
VB1 = VB2 = VB3 = VB4
The highest level of VB1,VB2,VB3,VB4 must be aligned at
the same line. Ideal difference level between VB2 and VB3
should be within ± 110mV.
the same line. Ideal difference level between VB2 and VB3
should be within ± 110mV.
VB1
VB2
VB3
VB4
VB2 = VB3 = VB4
VB2 = VB3 = VB4 (Difference is within 70mV)
± 110mV
4-4. ADJUSTMENT FOR DIGITAL TEXTURE
ENHANCER (DTE) MODEL
Y LEVEL ADJUSTMENT
1. Select Video.
2. Input PAL Color Bar to TV set (white reference 100%).
3. Set the following condition:
2. Input PAL Color Bar to TV set (white reference 100%).
3. Set the following condition:
DTE
: ON
Picture Mode : Dynamic
4. Connect an oscilloscope to pin
1 (CV/Y in) of CN106, A
Board.
5. Set to Service Mode and YCT 08 ‘YOL’ with 1 and 4 of the
commander then adjust to VY within spec with 3 and 6.
6. Then press
[MUTING]
→ - to write the data.
7. Select RF.
8. Repeat item 2 to 4.
9. Set to Service Mode and YCT 04 ‘SCT’ with 1 and 4 of the
8. Repeat item 2 to 4.
9. Set to Service Mode and YCT 04 ‘SCT’ with 1 and 4 of the
commander then adjust to VY within spec with 3 to 6.
10. Copy SCT data to NTSC (RF).
SUB COLOR (YCT) ADJUSTMENT
1. Select Video.
2. Input NTSC Color Bar.
3. Set the following condition:
2. Input NTSC Color Bar.
3. Set the following condition:
DTE
: ON
Picture Mode : Dynamic
NTSC 75% Color Bar
NTSC 75% Color Bar
4. Connect an oscilloscope to pin
2 (B-Y in) of CN303, A Board.
5. Set to Service Mode and YCT 0A ‘COL’ with 1 and 4 of the
commander then adjust to VB within spec with 3 and 6.
6. Then press
[MUTING]
→ - to write the data.
7. Select RF.
8. Repeat item no 2 to 4.
9. Set to Service Mode and YCT 03 ‘COL’ with 1 and 4 of the
8. Repeat item no 2 to 4.
9. Set to Service Mode and YCT 03 ‘COL’ with 1 and 4 of the
commander then adjust the waveform within spec with 3 and
6.
6.
10. Then press
[MUTING]
→ - to write the data.
11. Input PAL Color Bar (75%) and repeat item no 8 to 10.
SCT Setting (Video Mode) : 07h (NTSC & PAL)
SPEC: VY : 1.2 Vpp ± 0.05m Vpp
SPEC
:
VIDEO
: VB = 0.931 Vpp ± 50 mVpp
RF
: VB = 0.931 Vpp ± 50 mVpp
VY
VB
Click on the first or last page to see other KV-AR29M31 service manuals if exist.