DOWNLOAD Sony KV-AR25M86 Service Manual ↓ Size: 7.11 MB | Pages: 122 in PDF or view online for FREE

30

Additional Information

x

Connecting to the video input terminal ( t )

Connecting to the monitor output terminal ( T )

1

2

3

R

L

Y

C

B

C

R

3

L(MONO)

R

1

2

3

R

L

Y

C

B

C

R

31

Additional Information

1 Using an audio cable, connect R and L under 

 (component video input) on your

TV to the LINE OUT, AUDIO R and L output connectors on your DVD player.

2 Using a component video cable, connect Y, C

B

, and C

R 

under

 (component video input) on your TV to the COMPONENT VIDEO OUT Y, C

B

,

and C

R

 output connectors on your DVD player.

3 Press DVD on the remote to watch the 

 (component video input) and “DVD”

will appear on your screen.

Notes
• If your DVD player can ouput interlace and progressive mode signals, select the interlace

output when connecting to 

 (component video input) on your TV. Your TV can receive

either 525i/60Hz or 625i/50Hz interlace signals.

• Some DVD player terminals may be labeled differently:

• When both 

 (S video) and 

 (video) for t 1 or t 3 are connected at the same time,

(S video) is automatically selected.  To view 

 (video), disconnect the S video cable.

• If you select “DVD” on your TV screen, the signal from the T (monitor output) jacks will not

be output properly. This does not indicate a malfunction.

Y (green)

Y

C

B

 (blue)

C

B

, P

B

, C

b

 or B-Y

C

R

 (red)

C

R

, P

R

, C

r

 or R-Y

VIDEO 

R-AUDIO-L

LINE  OUT

Y 

COMPONENT VIDEO OUT

S VIDEO OUT

C

B

 

C

R

 

32

Additional Information

• Check the antenna cable and connection

on the TV, VCR and at the wall.

• Check the antenna setup.

Contact a Sony dealer for advice.

• Display the “CH PRESET” menu and

select “MANUAL PROGRAM” to preset
the channel again.

• Try using a booster.

• Display the “CH PRESET” menu and

select “MANUAL PROGRAM”.
Then, select “

 SENS: LOW”.

• Turn off or disconnect the booster if it is in

use.

• Display the “CH PRESET” menu and

select the appropriate TV system
(“TV SYS”).

• Press SOUND or  

.

• The connection is loose

or the cable is
damaged.

• The antenna setup is

inappropriate.

• Channel presetting is

inappropriate or
incomplete.

• Signal transmission is

low.

• Broadcast signals are

too strong.

• The TV system setting

is inappropriate.

• PIP sound is selected

when PIP is displayed.

x

If you have any problem while viewing your TV, you can either use the Reset
function or check the Troubleshooting guide below. If the problem persists,
contact your Sony dealer.

Press the RESET button on your remote control.
Your TV will go blank for about half a second
then the picture will reappear with “RESET”
displayed on your TV screen for about 10 seconds.

Pressing RESET will set your TV to the factory
setting, but certain problems may be solved.

30

–

28

–

29

–

28

13

33

Additional Information

• The power cord,

antenna or VCR is not
connected.

• The TV is not turned

on.

• The volume level is too

low.

• The sound is muted.

• PIP sound is selected

when PIP is displayed.

• There is local

interference from cars,
neon signs, hair dryers,
power generators, etc.

• Broadcast signals are

reflected by nearby
mountains or
buildings.

• The antenna setup is

inappropriate.

• Use of a booster is

inappropriate.

• The color level setting

is too low.

• The color system

setting is
inappropriate.

• The antenna setup is

inappropriate.

• Check the power cord, antenna and VCR

connections.

• Press 

 ?/1

 (power).

• Press ! (main power) on the TV to turn

off the TV for about five seconds, then
turn it on again.

• Press 2 + to increase the volume level.

• Press % to cancel the muting.

• Press SOUND or  

.

• Do not use a hair dryer or other

equipment near the TV.

• Check the antenna setup. Contact a Sony

dealer for advice.

• Use a highly directional antenna.

• Use the fine tuning (“FINE”) function.

• Check the antenna setup. Contact a Sony

dealer for advice.

• Turn off or disconnect the booster if it is in

use.

• Display the “PICTURE” menu and select

“ADJUST” of “PICTURE MODE”, then
adjust the “COLOR” level.

• Display the “SETUP” menu and check the

color system (“COLOR SYS”) setting
(usually set this to “AUTO”).

• Check the antenna setup. Contact a Sony

dealer for advice.

30

9

8

9

9

13

–

–

–

29

–

–

21

25

–