DOWNLOAD Sony KV-AR253M50 Service Manual ↓ Size: 5.14 MB | Pages: 67 in PDF or view online for FREE

– 29 –

GA US

(US Model Destination)

0 = US/CANADA/Latin
1 = Taiwan/Korea/Philippine
      (Wake-up timer enable)
      (GA Surround Spec:OFF,
      SIMULATED, SRS)

3D OSD

(BX1L Full version GA Multi

0 = Normal with 3D Intelligent picture OSD

Destination ONLY)

1 = Disable 3D Intelligent picture OSD

Feature 2

(Temporary for BX1L)

0 = Comb Not available
1 = Comb available

Feature 1

(Temporary for BX1L)

0 = PiP Not Available
1 = PiP available

OSD Language Selection

US (GA NTSC)

1x1x = Complicated Chinese
1xx1 = Korean (note: for BX1L, combination
            of C.Chinese & Korean not available)

GA

1xxx = Simplified Chinese
x1xx = Arabic
xx1x = Thai
xxx1 = Vietnamese

GA US

3D OSD

Feature 2

Feature 1

OSD Language Selection

DIC

0

0

0

0

0

0

0

1

1

– 30 –

1. Select Video.
2. Input PAL 100% Color Bar.
3. Set to following condition:

PICTURE 100%,COLOR 50%, BRIGHTNESS 50%, HUE
Center, SHP 50%.

4. Set the PICT 006 WTS to 00h.
5. Connect an oscilloscope to pin 2 (B OUTPUT) of CN004

A Board.

6. Set the service mode and select  SADJ 004 "SCOL" with

1

 and 

4

 of the commander then adjust to

VB2=VB3=VB4 with 

3

 and 

6

 (For PAL), write the data

as below :
Add 2 steps to SCOL (PAL) - 25" and 29".
Add 6 steps to SCOL (PAL) - 34".

7. Copy "SCOL 50 PAL(Video)"data to "SCOL 50

SECAM(Video)"

8. Copy "SCOL 50 PAL(Video)" and "SCOL 50 SECAM

(Video)" data to "SCOL 50 PAL(TV)" and "SCOL 50
SECAM(TV)" table.

9. Input NTSC 75% Color Bar to TV set and repeat item

3-5.

10. Set the service mode and select SADJ 004 "SCOL" with

1

 and 

4

 of the commander then adjust to

VB1 = VB4. Write the data as below :
Add 5 steps to SCOL (NTSC) - 25"
Add 3 steps to SCOL (NTSC) - 29".
Add 6 steps to SCOL (NTSC) - 34".

11. Copy "SCOL 60 NTSC(Video)"data to "SCOL 60

NTSC(TV)"

12. Copy "SCOL 50 PAL"data to "SCOL 50 YUV" table and

"SCOL 60 NTSC" data to "SCOL 60 YUV".

13. Set WTS back to original data.

VB2 = VB3 = VB4(For PAL sub color adjustment)
VB1 = VB4(For NTSC sub color adjustment)

(Difference is within 70mV)

VB1

VB2

VB3

VB4

1. Select YUV input.
2. Input NTSC 3.58 Color Bar into YUV mode.
3. Connect an oscilloscope to pin 2 (B output) of CN004.

Set the service mode and select YC 013 "TINT" with 

1

and 

4

 of the commander then adjust to

VB1=VB2=VB3=VB4 with 

3

 and 

6

.

5. Then press [MUTING] 

t 

-

 to write the data.

The highest level of VB1, VB2, VB3, VB4 must be aligned at
the same line.
The ideal difference between VB2 and VB3 is within ± 80mV.

Picture Mode: Personal
1. Select Video mode.
2. i)Input PAL Color Bar toTV set. (Other)

ii)Input NTSC 75% Color Bar (NTSC model).

3. Set the following condition:

PICTURE 100%, COLOR 0%,BRIGHTNESS 50%

4. Connect oscilloscope to pin 4 (R Output) of CN004.
5. Set to Service Mode "PWL" PICT 003 to 00h and WHBL

017 "BLBG" to 01h.

6. Select SADJ 000 "PMAX" with 

1

 and 

4

 of the

commander then adjust VR within spec with 

3

 and 

6

.

VB1

VB2

VB3

VB4

VB1 = VB2 = VB3 = VB4

80mV

VR

NTSC

1.85±0.03Vpp

1.57±0.03Vpp

1.85±0.03Vpp

34"

29"

25"

PAL

2.15±

0.03Vpp

2.15±

0.03Vpp

2.15±

0.03Vpp

VR

Black

– 31 –

(V-Compression Adjustment)
1. Input SPCB signal(For NTSC models select Video mode)
2. Adjust condition to WIDE MODE : ON.
3. Copy (item from NORMAL MODE (50Hz) adjusted data

for the following items:
Service Item

GEOM: 003

VLIN

VERTICAL LINEARITY

010

VSLP

VERTICAL SLOPE (VS)

011

VSIZ

VERTICAL AMPLITUDE

012

SCOR

S-CORRECTION (SC)

4. Raise/lower data using the 

3

 and 

6

 buttons, select and

adjust the following item to obtain optimum image.
Service Item

GEOM:

000

HPOS

HORIZONTAL SHIFT (HS)

001

HPAR

HORIZONTAL
PARALLELOGRAM

002

HBOW

HORIZONTAL BOW

005

HSIZ

EW WIDTH (EW)

006

EWPW

EW PARABOLA/WIDTH (PW)

007

UCOP

EW UPPER CORNER
PARABOLA

008

LCOP

EW LOWER CORNER
PARABOLA

009

EWTZ

EW TRAPEZIUM

013

VPOS

VERTICAL SHIFT (VSH)

5. For Korea models only:

a) Copy adjusted 60Hz data to 50Hz
b) Add 6 steps to 50Hz "HPS" item and save data.

1. Input 525/60Hz signal.
2. Using the 

1

 and 

4

 buttons select category GEOM

(Service Mode.)

3. Raise/ lower data using the 

3

 and 

6

 buttons to obtain

optimum image

7. Copy PMAX data to TV models.
8. Select "WIDE" mode for TV & Video mode. Write the

PMAX Data – 6 steps" (for model with V-Compression
features only).

9. Set the PWL & BLBG back to (PWL: 01h and

BLBG: 00h)

1. Receive cross hatch/dot signal.
2. Adjust RV1801 on C-Board to make H-Trapezoid

distortion best.

1. Set to Service Mode.
2. Input SPCB Signal (For NTSC models select Video mode)
3. Using the 

1

 and 

4

 buttons select, category GEOM

(service mode) Raise/lower data using the 

3

 and 

6

buttons to adjust the following items:-
Service Item

GEOM: 000

HPOS

HORIZONTAL SHIFT (HS)

001

HPAR

HORIZONTAL
PARALLELOGRAM

002

HBOW

HORIZONTAL BOW

003

VLIN

VERTICAL LINEARITY

005

HSIZ

EW WIDTH (EW)

006

EWPW

EW PARABOLA/WIDTH
(PW)

007

UCOP

EW UPPER CORNER
PARABOLA

008

LCOP

EW LOWER CORNER
PARABOLA

009

EWTZ

EW TRAPEZIUM

010

VSLP

VERTICAL SLOPE (VS)

011

VSIZ

VERTICAL AMPLITUDE

012

SCOR

S-CORRECTION (SC)

013

VPOS

VERTICAL SHIFT (VSH)

4. For Korea models only:

a) For GEOM items, copy adjusted 60Hz to 50Hz
b) Add 6 steps to 50Hz "HPOS" item and save data.
c) Add 3 steps to 50Hz "HSIZ" item and save data.

– 32 –

(

)

GEOM: 000

HPOS HORIZONTAL SHIFT (HS)

001

HPAR

HORIZONTAL
PARALLELOGRAM

002

HBOW

HORIZONTAL BOW

003

VLIN

VERTICAL LINEARITY

005

HSIZ

EW WIDTH (EW)

006

EWPW

EW PARABOLA/WIDTH
(PW)

007

UCOP

EW UPPER CORNER
PARABOLA

008

LCOP

EW LOWER CORNER
PARABOLA

009

EWTZ

EW TRAPEZIUM

010

VSLP

VERTICAL SLOPE (VS)

011

VSIZ

VERTICAL AMPLITUDE

012

SCOR

S-CORRECTION (SC)

013

VPOS

VERTICAL SHIFT (VSH)

(V-Compression Adjustment)
1. Input Monoscope signal
2. Adjust condition to WIDE MODE : ON.
3. Copy (item from NORMAL MODE 60Hz) adjusted data for

the following items:

Service Item

GEOM: 003

VLIN

VERTICAL LINEARITY

010

VSLP

VERTICAL SLOPE (VS)

011

VSIZ

VERTICAL AMPLITUDE

012

SCOR

S-CORRECTION (SC)

4. Raise/lower data using 

3

 and 

6

 buttons, select and

adjust the following item to obtain optimum image.

   Service Item

GEOM: 000

HPOS HORIZONTAL SHIFT (HS)

001

HPAR

HORIZONTAL
PARALLELOGRAM

002

HBOW

HORIZONTAL BOW

005

HSIZ

EW WIDTH (EW)

006

EWPW

EW PARABOLA/
WIDTH (PW)

007

UCOP

EW UPPER CORNER
PARABOLA

008

LCOP

EW LOWER CORNER
PARABOLA

009

EWTZ

EW TRAPAZIUM

013

VPOS

VERTICAL SHIFT (VSH)

1. Input Monoscope signal.
2. Activate the Service Mode.
3. Select the HPOS item with 

1

 and 

4

.

4. Adjust the value of HPOS with 

3

 and 

6

 for the best

horizontal center.

5. Press [MUTING] then 

-

 to save into the memory.

1. Input Monoscope signal.
2. Activate the Service Mode.
3. Select HSIZ with 

1

 and 

4

.

4. Adjust with 

3

 and 

6

 for the best horizontal size.

5. Press [MUTING] then 

-

 to save into the memory.

Service Item

GEOM 1

HSZ ( H SIZE)