Sony KV-28EW20B Service Manual ▷ View online
- 5 -
FE-2 SELF DIAGNOSTIC SOFTWARE
The identification of errors within the FE-2 chassis is triggered in one of two ways :- 1: Busy or 2: Device failure to respond to IIC. In the event
of one of these situations arising the software will first try to release the bus if busy (Failure to do so will report with a continuous flashing
LED) and then communicate with each device in turn to establish if a device is faulty. If a device is found to be faulty the relevant device number
will be displayed through the LED (Series of flashes which must be counted) See table 1., non fatal errors are reported using this method.
Each time the software detects an error it is stored within the NVM. See Table 2.
of one of these situations arising the software will first try to release the bus if busy (Failure to do so will report with a continuous flashing
LED) and then communicate with each device in turn to establish if a device is faulty. If a device is found to be faulty the relevant device number
will be displayed through the LED (Series of flashes which must be counted) See table 1., non fatal errors are reported using this method.
Each time the software detects an error it is stored within the NVM. See Table 2.
Flash Timing Example : e.g. error number 3
StBy LED
ON
ON
ON
OFF
OFF
Table 1
How to enter into Table 2
1.
Turn on the main power switch of the TV set and enter into
the ‘Stanby Mode’.
the ‘Stanby Mode’.
2.
Press the following sequence of buttons on the Remote
Commander.
Commander.
i+
5
-
(ON SCREEN (DIGIT 5) (VOLUME -) (TV)
DISPLAY)
DISPLAY)
3.
The following table will be displayed indicating the error
count.
count.
Table 2
Note: To clear the error count data press ‘80’ on the Remote
commander.
commander.
U
N
E
M
R
O
R
R
E
2
0
E
3
0
E
4
0
E
5
0
E
6
0
E
7
0
E
8
0
E
9
0
E
0
1
E
1
1
E
E
M
I
T
G
N
I
K
R
O
W
S
R
U
O
H
S
E
T
U
N
I
M
P
C
O
A
/
N
P
V
O
C
N
Y
S
V
R
K
I
C
I
I
M
V
N
E
L
G
N
U
J
R
E
N
U
T
P
D
N
U
O
S
V
8
)
5
5
2
,
0
(
)
5
5
2
,
0
(
)
5
5
2
,
0
(
)
5
5
2
,
0
(
)
5
5
2
,
0
(
)
5
5
2
,
0
(
)
5
5
2
,
0
(
)
5
5
2
,
0
(
)
5
5
2
,
0
(
)
5
5
2
,
0
(
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
2
1
1
e
g
a
s
s
e
M
r
o
r
r
E
D
E
L
e
d
o
C
r
o
r
r
e
o
N
0
0
d
e
v
r
e
s
e
R
1
0
)
n
o
i
t
c
e
t
o
r
P
t
n
e
r
r
u
C
r
e
v
O
(
P
C
O
2
0
d
e
s
U
t
o
N
3
0
c
n
y
S
l
a
c
i
t
r
e
V
o
N
4
0
n
o
r
e
w
o
p
t
a
r
o
r
r
E
R
K
I
5
0
n
o
r
e
w
o
p
t
a
w
o
l
s
e
n
il
a
t
a
d
r
o
/
d
n
a
k
c
o
l
c
s
u
b
C
I
I
6
0
n
o
r
e
w
o
p
t
a
e
g
d
e
l
w
o
n
k
c
a
s
u
b
C
I
I
o
n
M
V
N
7
0
d
e
s
U
t
o
N
8
0
n
o
r
e
w
o
p
t
a
e
g
d
e
l
w
o
n
k
c
a
o
n
r
e
n
u
T
9
0
r
o
r
r
E
r
o
s
s
e
c
o
r
P
d
n
u
o
S
0
1
r
o
r
r
e
s
t
l
o
v
8
r
e
ll
o
r
t
n
o
c
e
l
g
n
u
J
1
1
- 6 -
8
First Time Operation
Your TV is now ready for use
4
The Auto Tuning menu appears on the screen. Press the
OK button to select Yes.
OK button to select Yes.
5
The TV starts to automatically search and store all
available broadcast channels for you.
This procedure could take some minutes. Please be
patient and do not press any buttons, otherwise the
automatic tuning will not be completed.
If no channels were found during the auto tuning process
then a new menu appears automatically on the screen
asking you to connect the aerial. Please connect the aerial
(see page 6) and press OK. The auto tuning process will
start again.
then a new menu appears automatically on the screen
asking you to connect the aerial. Please connect the aerial
(see page 6) and press OK. The auto tuning process will
start again.
6
After all available channels are captured and stored,
the
Programme Sorting menu appears automatically
on the screen enabling you to change the order in
which the channels appear on the screen.
a)
If you wish to keep the broadcast channels in the
tuned order, go to step 7.
b)
If you wish to store the channels in a different order:
1 Press the
or
button to select the programme
number with the channel (TV Broadcast) you wish
to rearrange, then press the
button.
2 Press the
or
button to select the new
programme number position for your selected
channel (TV Broadcast), then press
.
3 Repeat steps b)1 and b)2 if you wish to change
the order of the other channels.
7
Press the MENU button to remove the menu from the
screen.
No channel found
Please connect aerial
Confirm
OK
Programme: 01
System: B/G
Channel: C21
Auto Tuning
Searching...
Programme Sorting
Select channel:
Exit:
Exit:
MENU
Programme:
01 TVE
02 TVE2
03 TV3
04 C33
05 C27
06 C58
01 TVE
02 TVE2
03 TV3
04 C33
05 C27
06 C58
OK
Programme Sorting
Select new position:
Exit:
Exit:
MENU
Programme:
01 TVE
02 TVE2
03 TV3
04 C33
05 C27
01 TVE
02 TVE2
03 TV3
04 C33
05 C27
06 C58
05 C27
OK
Do you want to start
automatic tuning?
Yes
No
OK
K
K
K
K
!
!
MENU
7
GB
Language
Select Language:
v
Svenska
Norsk
English
Nederlands
Français
Italiano
Norsk
English
Nederlands
Français
Italiano
i
V
OK
If picture slants, please
adjust picture rotation
Not necessary
Adjust now
OK
K
K
Switching On the TV and Automatically Tuning
The first time you switch on your TV, a sequence of menu screens appear on the TV enabling you
to: 1) choose the language of the menu screen, 2) adjust the picture slant 3) search and store all
available channels (TV Broadcast) and 4) change the order in which the channels (TV Broadcast)
appear on the screen.
However, if you need to change any of these settings at a later date, you can do that by selecting the
appropriate option in the
to: 1) choose the language of the menu screen, 2) adjust the picture slant 3) search and store all
available channels (TV Broadcast) and 4) change the order in which the channels (TV Broadcast)
appear on the screen.
However, if you need to change any of these settings at a later date, you can do that by selecting the
appropriate option in the
(Set Up menu) or by pressing the Auto Start Up Button
on the
TV set.
First Time Operation
continued...
1
Connect the TV plug to the mains socket (220-240V AC, 50Hz)
The first time the TV set is connected, it is usually turned on. If
the TV is off, press the
The first time the TV set is connected, it is usually turned on. If
the TV is off, press the
on/off button on the TV set to turn
on the TV.
The first time you switch on the TV, a Language menu displays
automatically on the TV screen.
The first time you switch on the TV, a Language menu displays
automatically on the TV screen.
2
Press the
or
button on the remote control to select the
language, then press the OK button to confirm your selection.
From now on all the menus will appear in the selected language.
From now on all the menus will appear in the selected language.
3
Because of the earth’s magnetism, the picture might slant. The
Picture Rotation menu allows you to correct the picture slants
if it is necessary.
if it is necessary.
a)
If it is not necessary, press
or
to select Not
necessary and press OK.
b)
If it is necessary, press
or
to select Adjust now, then
press OK and correct any slant of the picture between –5 and
+5 by pressing
+5 by pressing
or
. Finally press OK to store.
The operating instructions mentioned here are partial abstracts from the ‘Operating
Instruction Manual’. The page numbers of the ‘Operating Instruction Manual’ remain
as in the manual.
Instruction Manual’. The page numbers of the ‘Operating Instruction Manual’ remain
as in the manual.
SECTION 1
GENERAL
- 7 -
9
GB
Introducing and Using the Menu System
Your TV uses an on-screen menu system to guide you through the operations. Use the
following buttons on the Remote Control to operate the menu system:
following buttons on the Remote Control to operate the menu system:
1
Press the MENU button to switch the first level menu on.
Menu System
2
• To highlight the desired menu or option, press
or
.
• To enter to the selected menu or option, press
.
• To return to the last menu or option, press
.
• To alter settings of your selected option, press
/
/
or
.
• To confirm and store your selection, press OK.
3
Press the MENU button to remove the menu from the screen.
continued...
Menu Guide
PICTURE ADJUSTMENT
The “Picture Adjustment” menu allows you to alter
the picture adjustments.
The “Picture Adjustment” menu allows you to alter
the picture adjustments.
To do this: after selecting the item you want to alter
press
press
. then press repeatedly
/
/
or
to adjust it and finally press OK to store the new
adjustment.
This menu also allows you to customise the
picture mode based on the programme you are
watching:
adjustment.
This menu also allows you to customise the
picture mode based on the programme you are
watching:
Personal (for individual settings).
Live (for live broadcast programmes, DVD
Live (for live broadcast programmes, DVD
and Digital Set Top Box receivers).
Movie (for films).
Level 1
Level 2
Level 3 / Function
Picture Adjustment
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
Contrast
Brightness
Colour
Sharpness
Hue
Reset
OK
Picture Adjustment
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
Contrast
Brightness
Colour
Sharpness
Hue
Reset
OK
• Brightness, Colour and Sharpness can only be altered if “Personal” mode is selected.
• Hue is only available for NTSC colour signal (e.g: USA video tapes).
• Select Reset and press OK to reset the picture to the factory preset levels.
• Hue is only available for NTSC colour signal (e.g: USA video tapes).
• Select Reset and press OK to reset the picture to the factory preset levels.
K
MENU
MENU
12
Menu System
continued...
PROGRAMME SORTING
The “Programme Sorting” option in the “Set Up”
menu allows you to change the order in which the
channels (TV Broadcast) appear on the screen.
The “Programme Sorting” option in the “Set Up”
menu allows you to change the order in which the
channels (TV Broadcast) appear on the screen.
To do this: after selecting the option, press
and
then proceed in the same way as in step 6 b) of the
section “Switching On the TV and Automatically
Tuning”.
section “Switching On the TV and Automatically
Tuning”.
PROGRAMME LABELS
The “Programme Labels” option in the “Set Up”
menu allows you to name a broadcast channel using
up to five characters (letters or numbers).
The “Programme Labels” option in the “Set Up”
menu allows you to name a broadcast channel using
up to five characters (letters or numbers).
To do this:
1 After selecting the option, press
1 After selecting the option, press
, then
press
or
to select the programme number
with the channel you wish to name.
2 Press
. With the first element of the Label
column highlighted, press
or
to select a
letter or number (select “-“ for a blank), then
press
press
to confirm this character. Select the other
four characters in the same way. Finally press OK
to store.
to store.
AV PRESET
The “AV Preset” option in the “Set Up” menu allows
you to designate a name to the external equipment
you have connected to the sockets of this TV.
The “AV Preset” option in the “Set Up” menu allows
you to designate a name to the external equipment
you have connected to the sockets of this TV.
To do this:
1 After selecting the option, press
1 After selecting the option, press
, then press
or
to select the input source you wish to
name (AV1 and AV2 are for the rear Scarts and
AV3 for side connectors). Then press
AV3 for side connectors). Then press
.
2 In the label column automatically appears a label:
a) If you want to use one of the 6 predefined labels
(CABLE, GAME, CAM, DVD, VIDEO or
SAT), press
SAT), press
or
to select the desired
label and finally press OK to store.
b) If you want to set a different label, select Edit
and press
. Then with the first element
highlighted, press
or
to select a letter,
number or “-“ for a blank, then press
to
confirm this character. Select the other four
characters in the same way and finally press
OK to store.
characters in the same way and finally press
OK to store.
Level 1
Level 2
Level 3 / Function
Picture Adjustment
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
Contrast
Brightness
Colour
Sharpness
Hue
Reset
OK
Set Up
Language/Country
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
OK
Set Up
Language/Country
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
OK
Picture Adjustment
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
Contrast
Brightness
Colour
Sharpness
Hue
Reset
OK
Set Up
Language/Country
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
OK
Set Up
Language/Country
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
OK
Picture Adjustment
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
Contrast
Brightness
Colour
Sharpness
Hue
Reset
OK
Set Up
Language/Country
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
OK
Set Up
Language/Country
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
OK
- 8 -
13
GB
Menu System
continued...
MANUAL PROGRAMME PRESET
The “Manual Programme Preset” option in the “Set
Up” menu allows you to:
The “Manual Programme Preset” option in the “Set
Up” menu allows you to:
a)
Preset channels or a video input source one
by one to the programme order of your
choice. To do this:
choice. To do this:
1 After selecting the ”Manual Programme Preset”
option, press
then with Programme option
highlighted press
.
Press
or
to select on which programme
number you want to preset the channel (for VCR,
select programme number “0”). Then press
select programme number “0”). Then press
.
2 After selecting the Channel option, press
.
Then press the number buttons to enter directly
the channel number of the TV Broadcast or the
channel of the VCR signal. If you do not know the
channel number, press
channel of the VCR signal. If you do not know the
channel number, press
or
to search for it.
When you tune the desired channel, press OK
twice to store.
twice to store.
Repeat all the above steps to tune and store more
channels.
channels.
b)
Label a channel using up to five characters.
To do this: Highlighting the Programme
option, press the PROG +/- button to select the
programme number with the channel you wish to
name. When the programme you want to name
appears on the screen, select the Label option and
press
option, press the PROG +/- button to select the
programme number with the channel you wish to
name. When the programme you want to name
appears on the screen, select the Label option and
press
. Next press
o
r
to select a letter,
number or “-“ for a blank. Press
to confirm
this character. Select the other four characters in
the same way. After selecting all the characters,
press OK twice to store.
the same way. After selecting all the characters,
press OK twice to store.
Level 1
Level 2
Level 3 / Function
Picture Adjustment
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
Contrast
Brightness
Colour
Sharpness
Hue
Reset
OK
Set Up
Language/Country
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
OK
Set Up
Language/Country
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
OK
14
Menu System
continued...
c)
Normally the automatic fine tuning (AFT) is
operating, however you can manually fine tune
the TV to obtain a better picture
if the picture is distorted.
operating, however you can manually fine tune
the TV to obtain a better picture
if the picture is distorted.
To do this: while watching the channel (TV
Broadcast) you wish to fine tune, select the AFT
option and press
Broadcast) you wish to fine tune, select the AFT
option and press
. Next press
or
to
adjust the fine tuning between -15 and +15.
Finally press OK twice to store.
Finally press OK twice to store.
d)
Skip any unwanted programme numbers when
they are selected with the PROG +/- buttons.
To do this: Highlighting the Programme
option, press the PROG +/- button to select the
programme number you want to skip. When the
programme you want to skip
appears on the screen, select the Skip option and
press
programme you want to skip
appears on the screen, select the Skip option and
press
. Next press
or
to select Yes.
Finally press OK twice to confirm and store.
To cancel this function afterwards, select “No”
instead of “Yes” in the step above.
instead of “Yes” in the step above.
Level 1
Level 2
Level 3 / Function
Picture Adjustment
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
Contrast
Brightness
Colour
Sharpness
Hue
Reset
OK
Set Up
Language/Country
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
OK
Set Up
Language/Country
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
OK
Click on the first or last page to see other KV-28EW20B service manuals if exist.