DOWNLOAD Sony KV-2199M5J Service Manual ↓ Size: 3.8 MB | Pages: 36 in PDF or view online for FREE

– 7 –

Each time you press SELECT, the screen changes as
follows:

•

You can also use SELECT and 

.

 

+/– on the TV to adjust the

picture setting.

Change the “TV SYSTEM” (for KV-J21MF2J/J14M1J) or
“COLOR SYSTEM” setting or adjust the “COLOR”
level in the on-screen display until the color becomes
normal.

…

Change the “COLOR SYSTEM” setting or adjust the
“COLOR” level in the on-screen display until the color
becomes normal.

•

Normally set “COLOR SYSTEM” to “AUTO”.

terminal
Change the “TV SYSTEM” setting (for KV-J21MF2J/
J14M1J) in the on-screen display until the sound
becomes clear.

•

The sound mode feature is unavailable for your TV. Thus, the
SOUND MODE button on the remote commander is not used
for your TV.

Each time you press PIC MODE, the screen changes as
follows:

•

If you change the picture mode after the following
adjustments, the adjustment changes in accordance with the
picture mode.

÷

0

PIC MODE

SELECT

SELECT

PROGR

If you have any problems, read this manual again and
check the countermeasure for each of the symptoms
listed below.
If the problem persists after trying the methods below,
contact your nearest authorized service center or dealer.

/Check the antenna.
/Check the antenna connection on the TV

and on the wall.

/Check the TV SYSTEM setting (for

KV-J21MF2J/J14M1J).

/ This may be caused by local interference

(e.g. cars, neon signs and hair dryers).
Adjust the antenna for minimum interference.

/ This may be caused by reflections from

nearby mountains or buildings. A highly
directional antenna may improve the
picture.

/Check the TV SYSTEM setting (for

KV-J21MF2J/J14M1J).

/ Press 

U

 or 

u

.

/ Check the antenna connection.
/ Check the VCR connections.
/ Check the power cord connection.
/ Check the standby mode.

/ Press 

.

 +.

/ Press 

¤

.

/ Adjust the COLOR level in the on-screen

display.

/ Check the COLOR SYSTEM setting.

/ Even if the picture or the sound is normal,

changes in the room temperature
sometimes make the TV cabinet expand or
contract, making a noise. This does not
indicate a malfunction.

•

The supplied remote commander is used on several models of
the TV.  If you do not find instructions for some controls that
are on the remote commander, that means your TV does not
employ the features of those controls, e.g. 

 and SOUND

MODE.

•

When you turn on the TV, you may hear the “boon” sound
that is caused by the demagnetization of the TV. This does not
indicate a malfunction.

•

The picture color may become abnormal if you change the
direction of your TV. To obtain the normal picture color, press

U

 on the TV to turn off the TV for five minutes and then turn

it on again.

•

Design and specifications are subject to change without notice.

•

All contents in the instruction manual are subject to change
without notice.

WARNING
Do not install the appliance in a confined space, such as
a bookcase or built-in cabinet.

– 8 –

For replacement of the Multi Button and Light Guide, cut the welded portions from them, exchange with the new parts, and fix them with

screws (+BVTP) respectively.

2

 Remove the rear cover.

1

 Five screws (BVTP4

×

16)

Lever

Lever

A board

A board

Cut

Multi button

Two screws

(BVTP 3x12)

– 9 –

1

a

2

b

1

2

3

•

3

c

•

NOTE : Short circuit the anode of the picture tube and the anode cap to the metal chassis, CRT shield or carbon paint on the

CRT, after removing the anode.

•

a

b

b

c

a

Anode button

2

 A board

3

 C board

5

 Deflection yoke

Cushion

6

 Four screws

     (Tapping screws)

1

 Anode cap

9

 Picture tube

4

 VM board

 

8

 Spring

7

 Demagnetization

              coil

– 10 –

•

The following adjustments should be made when a complete

realignment is required or a new picture tube is installed.

•

These adjustments should be performed with rated power

supply voltage unless otherwise noted.

Controls and switch should be set as follows unless otherwise noted:

PICTURE control ...........................................................  normal

BRIGHTNESS control ...................................................  normal

•

In order to reduce the influence of geomagnetism on the set's

picture tube, face it east or west.

•

Switch on the set's power and degauss with the degausser.

1. Input the white raster signal with the pattern generator.

Contrast

Brightness

2. Set the pattern generator raster signal to green.

3. Move the deflection yoke to the rear and adjust with the  purity

control so that the green is at the center and the blue and the red

take up equally sized areas on each side.

(See Figures 3-1 through 3-3.)

4. Move the deflection yoke forward and adjust so that the entire

screen is green. (See Figure 3-1.)

5. Switch the raster signal to blue, then to red and verify the

condition.

6. When the position of the deflection yoke has been decided,

fasten the deflection yoke with the screws.

7. If the beam does not land correctly in all the corners, use a

magnet to adjust it.

(See Figure 3-4.)

Perform the adjustments in order as follows :

1. Beam Landing

2. Convergence

3. Focus

4. White Balance

Note :  Test Equipment Required.

1. Color-bar/Pattern Generator

2. Degausser

3. Oscilloscope

}

normal

.................................................................................................................................................................................................................................

Purity control

GREEN

BLUE      RED

Deflection yoke positioning

corrects these areas.

Purity control corrects

this area.

Disk magnets or rotatable
disk magnets correct
these areas (a-d).

b  

c

a

d