Sony KV-2199M5J Service Manual ▷ View online
– 6 –
Operations
8
-EN
Watching the TV
Turning off the TV
To turn off the TV temporarily
Press
Press
u
on the remote commander. The
u
indicator
on the TV lights up.
To turn off the TV completely
Press
Press
U
on the TV.
If the power on the TV is turned off in standby mode, the
u
indicator on the TV may remain alight for a while.
Watching the video input
Press
…
.
To watch TV
Press
Press
;
.
Muting the sound
Press
¤
.
1
Press
U
to turn on the TV.
When the TV is turned on in standby mode, press
u
on the remote commander.
2
Select the TV program you want to watch.
To select a program position directly
Press the number button.
To select a two-digit program position, press
“-/--” before the number buttons.
For example: to select program position 25, press
“-/--,” and then “2” and “5.”
“-/--” before the number buttons.
For example: to select program position 25, press
“-/--,” and then “2” and “5.”
To scan through program positions
Press PROGR +/– until the program position you
want appears.
want appears.
3
Press
.
+/– to adjust the volume.
1
2
3
4
6
7
8
9
÷
0
5
PROGR
Operations
.
¤
MUTING
VIDEO
1
;
2
5
9
Operations
-EN
1
AUTO B/G
DYNAMIC
After 10 minutes
No wake up timer
After 12 hours
WAKE UP TIMER:10M
WAKE UP TIMER:OFF
WAKE UP TIMER:12H00M
+/–
SELECT
Displaying on-screen information
Press
.
The program position, local system, and TV settings are
displayed on the screen.
displayed on the screen.
0
Setting the Sleep Timer
You can set the TV automatically turned off as you
program.
program.
Press .
To cancel the Sleep Timer, press
repeatedly until
“SLEEP TIMER: OFF” appears, or turn off the TV.
Changing the on-screen display
language
language
You can use buttons on the remote commander or the
TV to change the on-screen display language.
TV to change the on-screen display language.
1
Press SELECT until the screen appears as
follows:
follows:
2
Press +/– to select “ ”.
Note
•
You can also use SELECT and
.
+/– on the TV to select the
on-screen display language.
•
If no buttons or controls are pressed for more than two hours
after the TV is turned on using the Wake Up Timer, the TV
automatically turns into standby mode. If you want to
continue watching the TV, press any button or control on the
TV or remote commander.
after the TV is turned on using the Wake Up Timer, the TV
automatically turns into standby mode. If you want to
continue watching the TV, press any button or control on the
TV or remote commander.
Setting the Wake Up Timer
You can set the TV automatically turned on as you
program.
program.
1
Press
©
repeatedly to set the timer.
The on-screen display appears and the indicator
on the TV lights up.
on the TV lights up.
2
If you want a particular TV program or video
input to be displayed using the Wake Up Timer,
select the TV program or video input.
input to be displayed using the Wake Up Timer,
select the TV program or video input.
3
Press
u
on the remote commander or set
the Sleep Timer to turn off the TV in
standby mode.
standby mode.
To cancel the Wake Up Timer, press
©
repeatedly
until “WAKE UP TIMER: OFF” appears, or turn off the
main power of the TV.
main power of the TV.
Notes
•
The Wake Up Timer starts immediately after the on-screen
display disappears.
display disappears.
•
The last TV program position or video input just before the TV
turns into standby mode will appear when the TV is turned on
using the Wake Up Timer.
turns into standby mode will appear when the TV is turned on
using the Wake Up Timer.
After 30 minutes
After 60 minutes
After 90 minutes
No sleep timer
-EN
SLEEP TIMER:30M
SLEEP TIMER:60M
SLEEP TIMER:OFF
SLEEP TIMER:90M
LANGUAGE / : ENGLISH
SELECT
: LANGUAGE /
– 7 –
Operations
10
-EN
Adjusting the
picture
picture
Each time you press SELECT, the screen changes as
follows:
follows:
2
Press +/– to adjust the item.
3
To adjust other items, repeat steps 1 and 2.
Note
•
You can also use SELECT and
.
+/– on the TV to adjust the
picture setting.
If the picture color is abnormal when receiving
programs through the
programs through the
(antenna) terminal
Change the “TV SYSTEM” (for KV-J21MF2J/J14M1J) or
“COLOR SYSTEM” setting or adjust the “COLOR”
level in the on-screen display until the color becomes
normal.
“COLOR SYSTEM” setting or adjust the “COLOR”
level in the on-screen display until the color becomes
normal.
If the picture is abnormal when receiving
programs through the
programs through the
…
(video input) jack
Change the “COLOR SYSTEM” setting or adjust the
“COLOR” level in the on-screen display until the color
becomes normal.
“COLOR” level in the on-screen display until the color
becomes normal.
Note
•
Normally set “COLOR SYSTEM” to “AUTO”.
If the sound is distorted or noisy when
receiving programs through the
receiving programs through the
(antenna)
terminal
Change the “TV SYSTEM” setting (for KV-J21MF2J/
J14M1J) in the on-screen display until the sound
becomes clear.
Change the “TV SYSTEM” setting (for KV-J21MF2J/
J14M1J) in the on-screen display until the sound
becomes clear.
Note on the SOUND MODE button
•
The sound mode feature is unavailable for your TV. Thus, the
SOUND MODE button on the remote commander is not used
for your TV.
SOUND MODE button on the remote commander is not used
for your TV.
Selecting the picture mode
Press PIC MODE until the mode you want
appears.
appears.
Each time you press PIC MODE, the screen changes as
follows:
follows:
Note
•
If you change the picture mode after the following
adjustments, the adjustment changes in accordance with the
picture mode.
adjustments, the adjustment changes in accordance with the
picture mode.
Adjusting the picture setting
1
Press SELECT until the item you want to
adjust appears.
adjust appears.
÷
0
SOUND
MODE
SELECT
PIC MODE
PIC MODE
PIC MODE
High contrast
picture
picture
Soft picture
(good for video
games)
(good for video
games)
DYNAMIC
STANDARD
SOFT
+/–
SELECT
Normal
picture
picture
Front of TV
(Operative for
NTSC signal
only)
NTSC signal
only)
SELECT
PROGR
Additional Information
11
-EN
Troubleshooting
If you have any problems, read this manual again and
check the countermeasure for each of the symptoms
listed below.
If the problem persists after trying the methods below,
contact your nearest authorized service center or dealer.
check the countermeasure for each of the symptoms
listed below.
If the problem persists after trying the methods below,
contact your nearest authorized service center or dealer.
Snowy picture
Noisy sound
Noisy sound
/Check the antenna.
/Check the antenna connection on the TV
/Check the antenna connection on the TV
and on the wall.
/Check the TV SYSTEM setting (for
KV-J21MF2J/J14M1J).
Dotted lines or stripes
/ This may be caused by local interference
(e.g. cars, neon signs and hair dryers).
Adjust the antenna for minimum interference.
Adjust the antenna for minimum interference.
Double images or “ghosts”
/ This may be caused by reflections from
nearby mountains or buildings. A highly
directional antenna may improve the
picture.
directional antenna may improve the
picture.
Good picture
Noisy sound
Noisy sound
/Check the TV SYSTEM setting (for
KV-J21MF2J/J14M1J).
Additional Information
No picture
No sound
No sound
/ Press
U
or
u
.
/ Check the antenna connection.
/ Check the VCR connections.
/ Check the power cord connection.
/ Check the standby mode.
/ Check the VCR connections.
/ Check the power cord connection.
/ Check the standby mode.
Good picture
No sound
No sound
/ Press
.
+.
/ Press
¤
.
No color
/ Adjust the COLOR level in the on-screen
display.
/ Check the COLOR SYSTEM setting.
TV cabinet creaks
/ Even if the picture or the sound is normal,
changes in the room temperature
sometimes make the TV cabinet expand or
contract, making a noise. This does not
indicate a malfunction.
sometimes make the TV cabinet expand or
contract, making a noise. This does not
indicate a malfunction.
Note on the remote commander
•
The supplied remote commander is used on several models of
the TV. If you do not find instructions for some controls that
are on the remote commander, that means your TV does not
employ the features of those controls, e.g.
the TV. If you do not find instructions for some controls that
are on the remote commander, that means your TV does not
employ the features of those controls, e.g.
and SOUND
MODE.
Notes
•
When you turn on the TV, you may hear the “boon” sound
that is caused by the demagnetization of the TV. This does not
indicate a malfunction.
that is caused by the demagnetization of the TV. This does not
indicate a malfunction.
•
The picture color may become abnormal if you change the
direction of your TV. To obtain the normal picture color, press
direction of your TV. To obtain the normal picture color, press
U
on the TV to turn off the TV for five minutes and then turn
it on again.
•
Design and specifications are subject to change without notice.
•
All contents in the instruction manual are subject to change
without notice.
without notice.
WARNING
Do not install the appliance in a confined space, such as
a bookcase or built-in cabinet.
Do not install the appliance in a confined space, such as
a bookcase or built-in cabinet.
– 8 –
SECTION 2
DISASSEMBLY
2-1. REAR COVER REMOVAL
2-2. A BOARD REMOVAL
2-3. SERVICE POSITION
2-4. REPLACEMENT OF PARTS
For replacement of the Multi Button and Light Guide, cut the welded portions from them, exchange with the new parts, and fix them with
screws (+BVTP) respectively.
2-4-1. REPLACEMENT OF MULTI BUTTON
2
Remove the rear cover.
1
Five screws (BVTP4
×
16)
Lever
Lever
A board
A board
Cut
Multi button
Two screws
(BVTP 3x12)
– 9 –
1
Turn up one side of the rubber cap in
the direction indicated by the arrow
the direction indicated by the arrow
a
.
2
Using a thumb, pull up the rubber
cap firmly in the direction indicated
by the arrow
cap firmly in the direction indicated
by the arrow
b
.
1
Don’t hurt the surface of anode-caps with
sharp shaped objects!
sharp shaped objects!
2
Don’t press the rubber too hard so as not to
damage the inside of anode-caps!
A material fitting called the shatter-hook
terminal is built into the rubber.
damage the inside of anode-caps!
A material fitting called the shatter-hook
terminal is built into the rubber.
3
Don’t turn the foot of rubber over too hard!
The shatter-hook terminal will stick out or
damage the rubber.
The shatter-hook terminal will stick out or
damage the rubber.
•
HOW TO HANDLE AN ANODE-CAP
3
When one side of the rubber cap is
separated from the anode button,
the anode-cap can be removed by
turning up the rubber cap and
pulling it up in the direction of the
arrow
separated from the anode button,
the anode-cap can be removed by
turning up the rubber cap and
pulling it up in the direction of the
arrow
c
.
•
REMOVAL OF ANODE-CAP
NOTE : Short circuit the anode of the picture tube and the anode cap to the metal chassis, CRT shield or carbon paint on the
CRT, after removing the anode.
•
REMOVING PROCEDURES
2-5. DEMAGNETIZATION COIL AND PICTURE TUBE REMOVAL
a
b
b
c
a
Anode button
2
A board
3
C board
5
Deflection yoke
Cushion
6
Four screws
(Tapping screws)
1
Anode cap
9
Picture tube
4
VM board
8
Spring
7
Demagnetization
coil
Click on the first or last page to see other KV-2199M5J service manuals if exist.