Sony KP-HR432K90 / KP-HR532K90 / KP-HR532N90 / KP-HW572K90 Service Manual ▷ View online
– 29 –
KP-HR432K90/HR532K90/HR532N90/HW572K90
RM-Y909K
RM-Y908
RM-Y909K
RM-Y909K
3-11-4. PJE Adjustment
(Sub Deflection Adjustment)
Push the joystick
to
to
v
Push the joystick
to
to
V
Push the joystick
to
to
B
Push the joystick
to
to
b
• GRN CENT (horizontally/vertically)
<Adjustment for NTSC Full Mode>
• The adjustment should be done in the numerical order
given.
1. Green Adjustment
1) Place the caps on the red and blue lenses so that only the
green color is displayed.
2) Enter the monoscope signal to set.
3) Select the PJE mode.
4) Press “6” button on the commander to display internal test
signal (crosshatch).
5) Select “GRN CENT”, and adjust so that the picture coincide
in the center of screen.
Adjustment Type
Adjustment Item
GRN
RED
BLU
H / V
H / V
H / V
CENT
a
/
a
a
/
a
a
/
a
SKEW
a
/
a
a
/
a
a
/
a
SIZE
a
/
a
a
/
a
a
/
a
LIN
a
/
a
a
/
a
a
/
a
KEY
– /
a
– /
a
– /
a
PIN
a
/
a
a
/
a
a
/
a
MLIN
a
/ –
a
/ –
a
/ –
MSIZ
a
/ –
a
/ –
a
/ –
Adjustment
a : Yes
– : No
3. Operation Method for Fine Adjustment
1) Select the PJE mode.
2) Select FDIS so that the data at each position can be displayed
in the fine adjustment mode, and set the data to “01”.
3) Press “9” button on the commander, and the fine adjust-
ment mode will be active where a green marker appears in
the center of screen (in the case of GRN mode).
4) Press joystick, and the marker color will be switched be-
tween green (GRN mode) and white alternately.
5) Use “1” or “4” button on the commander, or the joystick
to move the marker to the position to be adjusted, where fine
adjustment can be made.
• When marker color is white.
(in this case, fine adjustment is disabled)
Operating the joystick can move the marker
up, down, or to the left or right freely.
• When marker color is green. (GRN mode)
1
: moves the marker clockwise from center to outside.
4
: moves the marker counterclockwise from outside to center.
• Fine adjustment can be made on the basis of marker
position using v, V, b, B directiom of the joystick.
6) Press “9” button on the commander to return to the coarse
adjustment mode.
CROSSHATCH
Move joystick
v
direction
Move joystick
B
direction
CROSSHATCH
Note: If the value of over the limit value, adjust these in the fine
adjustment .
adjustment .
Coarse Data Limit Valune.
Cent H 35
Cent H 35
±
170 V 20
±
170, Size H-75max, Lin H Blu
-425min, H Red 425max.
– 30 –
KP-HR432K90/HR532K90/HR532N90/HW572K90
RM-Y909K
RM-Y908
RM-Y909K
RM-Y909K
• GRN MLIN (horizontally)
11) Select “GRN MLIN”, and correct the sizes of the horizontal
line at the center of the screen are symmetrical left and right.
10) Select “GRN MSIZ”, and correct the space intervals for the
horizontal section of the screen are equal.
• GRN MSIZ (horizontally)
Push the joystick
to
to
B
Push the joystick
to
to
b
Push the joystick
to
to
B
Push the joystick
to
to
b
7) Select “GRN SKEW”, and correct the tilt of horizontal lines
and vertical lines.
8) Select “GRN SIZE”, and adjust so that each distance from
center to left end and to right end is equal. Adjust so that
each distance from center to top and to bottom is equal.
• GRN SIZE (horizontally/vertically)
9) Select “GRN LIN”, and adjust so that each space at the right
end and at the left end of screen is equal. Adjust so that each
space at the top and at the bottom of screen is equal.
• GRN LIN (horizontally/vertically)
Push the joystick
to
to
v
Push the joystick
to
to
V
Push the joystick
to
to
B
Push the joystick
to
to
b
Push the joystick
to
to
v
Push the joystick
to
to
V
Push the joystick
to
to
B
Push the joystick
to
to
b
Push the joystick
to
to
B
Push the joystick
to
to
b
Push the joystick
to
to
v
Push the joystick
to
to
V
Note: The SIZE and LIN, MSIZ and MLIN adjustments are
affected each other.
So adjust these mutually if necessary.
affected each other.
So adjust these mutually if necessary.
Push the joystick
to
to
v
Push the joystick
to
to
B
Push the joystick
to
to
b
Push the joystick
to
to
V
12) Select “GRN PIN”, and adjust so that right and left vertical
lines on the screen become straight. Adjust so that upper and
lower horizontal lines on the screen become straight.
• GRN PIN (horizontally/vertically)
13) Select “GRN KEY”, and adjust so that upper and lower hori-
zontal lines on the screen become parallel.
• GRN KEY (vertically)
Push the joystick
to
to
v
Push the joystick
to
to
V
Note: The VPINand KEY adjustments are affected each other.
So adjust these mutually if necessary.
So adjust these mutually if necessary.
• GRN SKEW (horizontally/vertically)
– 31 –
KP-HR432K90/HR532K90/HR532N90/HW572K90
RM-Y909K
RM-Y908
RM-Y909K
RM-Y909K
<Copy All Registration Data to Other modes>
1. Make sure that the adjustment for NTSC Full mode finished
and the data have already been written.
2. Select the PJE mode.
3. Select ALCP and set the data to “01”, and press
“MUTING”+“ENTER” buttons on the commander.
4. The data of NTSC Full mode are copied to all other modes.
5. Check in the other mode and adjust as the occasion demands.
Be sure to write data in each mode.
2. Red Adjustment
1) Place a cap on the blue lens so that green and red colors are
displayed.
2) Press “3” button on the commander to select RED mode.
3) Adjust the following items so that red lines overlap with
green lines.
• RED CENT (horizontally/vertically)
• RED SKEW (horizontally/vertically)
• RED SIZE (horizontally/vertically)
• RED LIN (horizontally/vertically)
• RED MSIZ (horizontally)
• RED MLIN (horizontally)
• RED PIN (horizontally/vertically)
• RED KEY (vertically)
4) Press “9” button on the commander to enter the fine adjust-
ment mode.
5) Make fine adjustment so that horizontal lines and vertical
lines overlap with green lines.
6) Press “9” button on the commander to return to the coarse
adjustment mode.
3. Blue Adjustment
1) All colors are displayed.
2) Press “3” button on the commander to select BLU mode.
3) Hereinafter, use same manner as that of red adjustment to
adjust so that the blue lines overlap with green and red lines.
4. Registration Data Writing
1) After each adjustment of green, blue, and red for the NTSC
Full mode finished, press “MUTING”+ “ENTER” buttons
on the commander to write registration data to the NVM.
14) Press “9” button on the commander to enter the fine adjust-
ment mode.
15) Make fine adjustment so that horizontal lines and vertical
lines become straight.
16) Press “9” button on the commander to return to the coarse
adjustment mode.
NTSC
VCOMP
NTSC
Full
HD
(1080i Full)
Copy Registration Data.
3-12. AUTO CONVERGENCE OFFSET
This adjustment must be performed after the registration adjust-
ment was made or after readjustment was made by any reason.
1. Darken the periphery of this set.
2. Enter the monoscope signal to set the NTSC Full mode.
3. Select the PJE mode.
4. Press “FLASH FOCUS” button on the front panel of the set.
(The offset value is now automatically stored)
5. Select “ ERR” of PJE mode.
Confirm ERR is “00”. If ERR is not “00”, recheck. (Refer to 3-
12.)
6. Exit the service mode.
3-13. AUTO REGISTRATION ERROR CODE LIST
If an error code is displayed after the set has been fully adjusted, cor-
rectly, plese check the following items : position, tilt and sizing. If
either of these adjustments are off, even slightli, the auto registration
pattern will not hit the four sensors properly. This occurs when the
internal generator patterns is being flashed on the screen for the sen-
sor to read. Therefore, auto registration (called auto convergence)
cannot operate properly causing an error code to be displayed. In or-
der for this function to operate properly, correct position, tilt and size
must be adjusted properly.
– 32 –
KP-HR432K90/HR532K90/HR532N90/HW572K90
RM-Y909K
RM-Y908
RM-Y909K
RM-Y909K
ERROR CODE LIST
ERROR
DESCRIPTION
REMEDY
CODE
00
No Error
10
Sensor 0 low output
Check sensor 0, connection/wiring, circuit, and pattern position
(Is pattern over sensor ?) Adjust “64 VUP” if necessary.
(Is pattern over sensor ?) Adjust “64 VUP” if necessary.
11
Sensor 1 low output
Check sensor 1, connection/wiring, circuit, and pattern position
(Is pattern over sensor ?) Adjust “69 HLB” if necessary.
(Is pattern over sensor ?) Adjust “69 HLB” if necessary.
12
Sensor 2 low output
Check sensor 2, connection/wiring, circuit, and pattern position
(Is pattern over sensor ?) Adjust “73 HRIV” if necessary.
(Is pattern over sensor ?) Adjust “73 HRIV” if necessary.
13
Sensor 3 low output
Check sensor 3, connection/wiring, circuit, and pattern position
(Is pattern over sensor ?) Adjust “68 VLOW” if necessary.
(Is pattern over sensor ?) Adjust “68 VLOW” if necessary.
20
Sensor 0 high output
Check sensor 0 and circuit.
21
Sensor 1 high output
Check sensor 1 and circuit.
22
Sensor 2 high output
Check sensor 2 and circuit.
23
Sensor 3 high output
Check sensor 3 and circuit.
30
V CENT or SKEW adjustment
Check “66 VMID” data and check registration condition.
loop overflow
31
H CENT or SKEW adjustment
Check “71 HMID” data and check registration condition.
loop overflow
32
H LIN or SIZE adjustment
Check “71 HMID” data and check registration condition.
loop overflow
40
V CENT regi data overflow
Check “66 VMID” data and confirm V CENT data (all mode) is not near 511.
41
H CENT regi data overflow
Check “71 HMID” data and confirm H CENT data (all mode) is not near 511.
42
V SKEW regi data overflow
Check “66 VMID” data and confirm V SKEW data (all mode) is not near 511.
43
H SKEW regi data overflow
Check “71 HMID” data and confirm H SKEW data (all mode) is not near 511.
44
H LIN regi data overflow
Check “71 HMID” data and confirm H CENT data (all mode) is not near 511.
45
H SIZE regi data overflow
Check “71 HMID” data and confirm H CENT data (all mode) is not near 511.
50
V CENT regi data overdrow
Check “66 VMID” data and confirm V CENT data (all mode) is not near –512.
51
H CENT regi data overdrow
Check “71 HMID” data and confirm H CENT data (all mode) is not near –512.
52
V SKEW regi data overdrow
Check “66 VMID” data and confirm V SKEW data (all mode) is not near –512.
53
H SKEW regi data overdrow
Check “71 HMID” data and confirm H SKEW data (all mode) is not near –512.
54
H LIN regi data overdrow
Check “71 HMID” data and confirm H CENT data (all mode) is not near –512.
55
H SIZE regi data overdrow
Check “71 HMID” data and confirm H CENT data (all mode) is not near –512.
60
H or V CENT offset overflow
Check “71 HMID” data and check “66 VMID” data.
61
H or V SKEW offset overflow
Check SKEW adjustment.
62
H SIZE or LIN offset overflow
Check “71 HMID” data, check “66 VMID” data and check SIZE and LIN adjustment.
70
H or V CENT offset overdrow
Check “71 HMID” data and check “66 VMID” data.
71
H or V SKEW offset overdrow
Check SKEW adjustment.
72
H SIZE or LIN offset overdrow
Check “69 HLB” data, check “73 HRIV” data and check SIZE and LIN adjustment.
80
SIZE limit error
Check that H SIZE is negative and not near zero.
0 : UPPER SENSOR
1 : LEFT SENSOR
2 : RIGHT SENSOR
3 : LOWER SENSOR
1 : LEFT SENSOR
2 : RIGHT SENSOR
3 : LOWER SENSOR
SCREEN
0
3
1
2
[SENSOR POSITION]
PJE 62 213
ERR
ERR
Color:
0=Green
1=Red
2=Blue
0=Green
1=Red
2=Blue
0-Green
1-Red
2-Blue
1-Red
2-Blue
Example: Blue low Level Sensor 3
ERROR EXAMPLE
AUTO REGI ERROR CODE FORMAT
Error Code:
(See Error List)
(See Error List)
Error codes in normal (customer) mode are not
displayed. You must enter PJED service mode to
see to the error code.
ERROR G
LO LEVEL S3
LO LEVEL S3
SENSOR POSITIONS
1
2
0
3
When executing flash focus in service mode, the
error will be displayed in text format (see below).
Click on the first or last page to see other KP-HR432K90 / KP-HR532K90 / KP-HR532N90 / KP-HW572K90 service manuals if exist.