DOWNLOAD Sony KP-FWS57M31 / KP-FWS57M91 Service Manual ↓ Size: 14.21 MB | Pages: 127 in PDF or view online for FREE

– 17 –

1. Receive 1080i/50Hz dot signal from HD/DVD 1 terminal.
2. Set  “Hi Fine” and PICTURE 100%, other 50% and white

balance “COOL” (VM OFF).

3. Blue 4 pole : make round in the center of screen.
4. Confirm that center dot focus is adjusted in focus (Fig.3-12a).
5. Adjust blue electrical focus to make the left side spot nearly

round by minimizing width and height (Slight overfocus is
OK) (Fig.3-12b).

6. Confirm that the green to blue spot size is within spec.

Blue center dot height shall be 

≤1.2 times the green dot heght.

7. Return making condition data to orignal data.

1. Input a cross hatch signal into VIDEO 1 (composite video

input).

2. Place a lens cover over red and blue lenses and project only

green.

3. Rotate the green lens and adjust to obtain the best lens focus at

the center area.

4. Fix lens screw.
5. Repeat above process for red and blue.

1. Input a cross-hatch signal into VIDEO 1.
2. Project only Green.
3. Rotate the green focus volume on the focus pack and adjust to

obtain the best focus at the center screen.

4. Repeat above process for red.

1. Receive the Dot signal (1080i/50Hz) from HD/DVD 1 termi-

nal.

2. Place the caps on the red and blue lens so that only the green

color is shown.

3. Turn the green focus volume of focus pack counter-clock-

wise, so that diameter of the dot become large.

4. Adjust the 2-pole magnet,  counter-clockwise and clockwise

center of the dot doesn't move (Use focus volume).

5. Center position is changed by 2-pole magnet adjustment.

So, center magnet adjustment and 2-pole magnet adjustment
are needed tracking adjustment.

6. Repeat same adjustment method for red and blue.

1. Turn Grenn focus volume of focus pack clockwise.
2. By using 4 pole magnets make the spot size round.
3. Repeat for red and blue.
4. Turn focus pack counter-clockwise and “Just Focus” red,

green and blue.

1. Turn blue focus volume of focus pack counter-clockwise, so

that diameter of the dot becomes large, and can see bright
core position.

2. Pay attentio to left side dot of the screen (Fig.3-10).
3. Adjustment 2 pole magnet, so that bright core position of dot

become center position of dot (Fig.3-11).

Use the center dot

NG

OK

Left-end dot
   (BLUE)

Right-end dot
   (BLUE)

Blue 2 Defocus

Adjustment Position

OK

Adjust Point center 

Adjust Point 

OK

NG

NG

Use the center dot

Bright Core 

Blue 2 Pole magnet

Adjustment Position

– 18 –

50 Hz

: Enter the PAL signal.

60 Hz

: Enter the NTSC signal.

WIDE 60 Hz : Enter the NTSC signal MENU WIDE ON.
WIDE 50 Hz : Enter the PAL signal MENU WIDE ON.

2. Selection of DRC Mode
1) Press  “DRC-MF (blue)” button on the commander, repeat-

edly until displays the mode that you want to select on the
screen.

→ DRC1250  →  DRC100  →  PROGRESSIV

Note : The DRC-MF mode is not selectable when using the

“PROGRAM INDEX” or “TWIN” mode is turned “ON”.

1) Press “MENU” button on the commander and move “

” up

or down to enter the “FEATURE” b “WIDE MODE”.

2) Move “

” up or down to select “ON” or “OFF”, and push

“

 (ENTER)” button.

3) Press “MENU” button to return to normal screen.

1) Press “

 (TWIN)” button on the commander.

2) Press “

 (TWIN)” button again to return to normal screen.

5. Selection of INDEX mode
1) Press “PROGR INDEX” button on the commander.
2) Press  “PROGR INDEX” button again to return to normal

screen.

1. Turn on the main power switch to place this set in standby

mode (LED will light in red.).

2. Press the buttons on the commander as follows, and enter ser-

vice mode.

3. After entering service mode, reset current aadjustment data.

Then turn off the power switch.

4. Turn on the main power switch and enter mode again as step 2

above.

TV

1

2

3

4

5

6

7

8

0

9

PROG

OPTION

RESET

Copy PAL data
to NTSC

blue

Adjustment item
up

Adjustment item
down
User control goes 
to the standard state

Write data to NVM

Read data from
NVM     

Change 
the PICTUER MODE

Initialize data
(Not stored)

Data down

Data up

Copy data to all
mode

Up : Category up
Down : Category down
Push : Enter

Enter the

“Service mode”

5

(DIGIT 5)

(VOLUME +)

ON SCREEN

DISPLAY

(         )

TV 

STANDBY

(       )

Enter the

“Reset”

8

(DIGIT 8)

(ENTER)

Service adjustment to this model can performed with the supplied

remote commander RM-1007.

50 Hz

60 Hz

WIDE 60 Hz WIDE 50 Hz

(PAL)

(NTSC)

(NTSC)

(PAL)

DRC1250

a

a

a

a

DRC100

a

a

a

a

TWIN

a

a

X

X

INDEX

a

a

X

X

– 19 –

PIC

SOU

DRCV

LUMA

YCTM

YCTS

YCTC

MCP

MID1

VSW

MID3

MID2

PFOP

* : When it moves from PJE to other categrys, 

repeat 1 or 4 button and press it. 

PFID

AP

GRN

PJE*

DDEV

COLR

CLTY

DEF1

DEF2

CRNR

RNR

MSMO

3CM

POWR

GUID

MIDE

CCPM

COMB

DEF3

DEF4

DEF5

BNR

SNNR

AWID

OSDP

ASEL

VSEL

OPM

OPB

SRV

OSD

MSP

TEXT

1. Set in the service mode.

2. Press “1” or “1” button on the commander, select the ad-

justment item, and press “3” or “6” button to change the

data.

3. Press “

 (MUTE)” button on the commander and it will indi-

cate “WRITE” on the screen.

4. Press “-” button on the commander to write into memory (The

“WRITE” display will be changed to red color while

executing, and back to “SERVICE”.).

Note : Before changing to other modes, press “

 (MUTE)” +

“-” buttons on the commander to write the data.

(Omission of this operation causes the data to be returned

to the data before adjustment.)

: Confirm the adjustment mode before writing data for data

values because to vary in each adjustment mode.

: The adjustment item that there are no relations in the ad-

justment is not to change data values because all items are

written in each adjustment mode.

1. After adjustment, turn off the AC main power switch off.

2. Turn the power switch ON and set in service mode.

3. Call the adjustment items again to confirm adjustments were

made.

1. Set the standby mode (Press “

 (TV STANDBY)” button on

the commander), then press “

 (TV STANDBY)” button

again, hereupon it becomes TV mode.

1. Set in the service mode, the following screen will appear.

2. Press “1” or “4” button on the commander to select the ad-

justment item.

3. Press “3” or “6” button on the commander to change the

adjustment data.

4. Move “

” up or down to select the adjustment category.

When move “

” up (category up), service mode changes in

the order as shown below.

OSD 0 OSV

32

SERVICE       60 480IL

000Q 3.1M 0010 0000 20 00 00 0000

Category Name Item Name

Mode

Item No.

Suffix No.

Total Power On time
(Hours)

Software

Version

Data

50 : PAL, SECAM
60 : NTSC

Button

Mode

Description

 + -

WRITE

Writes data to NVM.

7

 + -

READ

Reads data from NVM.

8

 + -

NORMAL

All user control goes to the standard.

5

 + -

INITIAL

Service data initialization. Not stored.

(Be sure not to use usually)

2

 + -

COPY

Do not operate with a remote

commander.

 + -

WRT5060 (The data vary with among mode.)

–

 20 

–

Category

Item

Function

Standard Data

Device Name

No.

Name

(Slave Address)

OSD

0

OSV

OSD V Position

32

CXP961F064(60H)

1

OSH

OSD H Position

13

2

FW1

OSD ODD/EVEN Field Window Setup #1

7

3

FW2

OSD ODD/EVEN Field Window Setup #2

20

4

VOF

OSD V Position (Offset)

*1

Item

Standard Data

No.

Name

OSD V OFFSET

INDEX60

FAVORITE50

FAVORITE60

TWIN50

TWIN60

HD50

HD60

MS

VCOMP

VCOMP60

VCOMP100

VCOMP120

4

VOF

32

32

32

32

32

32

32

32

32

32

32

32

Item

Standard Data

No.

Name

OSD V OFFSET

FULL51

FULL61

FULL101

FULL120

WDZM50

WDZM60

WDZM100

WDZM120

ZOOM50

ZOOM60

ZOOM100

ZOOM120

INDEX50

4

VOF

32

32

16

16

32

32

16

16

32

32

16

16

32

•

  : The data value of each mode. Other are set up by each mode.

•

  : Shaded items are fixed data.

•

  : Though data value is indicated on the screen, it is not used.

• Standard data listed on the Adjustment Item Table are reference valies, therefore it may be different for each model and each mode.

• Note for Different Data :

Those are the standard data values written on the microprocessor. Therefore , the data values of the modes and stored respectively in the memory.

In case of a device replacement, adjustment by rewriting the data value is necessary for some items.