DOWNLOAD Sony KP-57XBR10W / KP-65XBR10W Service Manual ↓ Size: 20.33 MB | Pages: 127 in PDF or view online for FREE

– 53 –

Adjustment

O : Yes

– : No

1. Select GRN CENT or GRN SIZE with the 1and 4 keys on

the remote commander.

2. Adjust the center of crosshatch line goes the middle vertically

and horizontally (GRN CENT) and set the size correctly (GRN

SIZE) with the joystick on the remote commander.

1. Select GRN SKEW with the 1 and 4 keys on the remote

commander.

2. Adjust the crosshatch line goes straight vertically and horizon-

tally with the joystick on the remote commander.

1. Select GRN PIN with the 1 and 4 keys on the remote

commander.

2. Adjust the crosshatch line goes straight horizontally with the

joystick on the remote commander.

Note : These are required when either severe miss-adjustment or

data loss occurred.

1. Press 9 key on the remote commander to shift to the fine

adjustment mode.

The green cursor (in the GRN mode) appears on the center of

the screen.

2. Use the 1and 4 keys or the joystick on the remote com-

mander, move the cursor (see below) everywhere you want to

adjust and adjust with the joystic keys on the remote com-

mander.

Marker movement by the 1 and 4 keys:

Press once the joystick the cursor turns green to white.

Then you can move the cursor up and down left and right every

where you want.

GRN
CENT

000

: Middle

000

GRN
SKEW

000

000

GRN
PIN

XXXX

000

Adjustment type

Display

Adjustment item

G

R

B

H/V

H/V

H/V

CENT

CENT

O/O

O/O

O/O

SKEW

SKEW

O/O

O/O

O/O

SIZE

SIZE

O/O

O/O

O/O

LIN

LIN

–/–

O/–

O/–

KEY

KEY

–/–

–/O

–/O

PIN

PIN

–/O

–/O

–/O

– 54 –

Press once again the joystick the cursor stops and returns

green, you can adjust around the cursor.

3. Press 9 key on the remote commander to shift to the coarse

adjustment mode.

1. Cover the blue picture lens with the lens cap to show the green

and red colors.

2. Press 3 key on the remote commander to shift the GRN

mode to the RED mode.

3. Select RED CENT or RED SKEW with the 1 and 4 keys

on the remote commander and adjust while tracking each other

alternately.

4. Adjust the red crosshatch lines go straight vertically and

horizontally and overlaps the green lines with the joystick on

the remote commander.

1. Select RED SIZE (vertically and horizontally) or RED LIN

(vertically) with the 1 and 4 keys on the remote com-

mander and adjust while tracking each other alternately.

2. Adjust the red crosshatch lines go straight vertically and

horizontally and overlaps the green lines with the joystick on

the remote commander.

1. Select RED KEY or PINCUSHION with the 1 and 4 keys

on the remote commander and adjust while tracking each other

alternately.

2. Adjust the red crosshatch lines go straight horizontally and

overlaps the green lines

with the joystick on the remote commander.

1. Press 9 key on the remote commander to shift to the fine

adjustment mode.

The red cursor (in the RED mode) appears on the center of the

screen.

2. Use the 1 and 4 keys or the joystick on the remote com-

mander, move the cursor everywhere you want to adjust and

adjust with the joystick on the remote commander.

1. Remove the lens cap from the blue picture lens to show full

color.

2. Press 3 key on the remote commander to shift the RED mode

to the BLU mode.

3. Adjust BLU CENT, BLU SKEW, BLU SIZE, BLU LIN, BLU

KEY and BLU PIN in the same procedure of the red registra-

tion adjustment.

1. Store the new adjustment (offset) value on the remote control

by pressing [MUTING] and [ENTER].

2. Press the FLASH FOCUS button on the front panel.

(The Offset value is now automatically stored.)

3. Check that no error message appears.

If an error message appears, recheck.

Note : In case of replacing CRTs, adjust the set-up adjustments

(items 3-1 to 3-8) and the registration adjustment (item 3-10).

In case of replacing two or three CRTs at the same time,

replace and adjust one by one.

– 55 –

*  In case of multiple error, last error is displayed.

*  Error code will be displayed on center of screen for 3 seconds.

E 11 B

E 11 B

R. G. B

SENSOR NUMBER

ERROR CODE 10

ERROR

3

0

6

4

7

5

1

2

SCREEN

0 : UPPER SENSOR

1 : LEFT SENSOR

2 : RIGHT SENSOR

3 : LOWER SENSOR

4 : UL SENSOR

5 : UR SENSOR

6 : LL SENSOR

7 : LR SENSOR

00

No Error

10

Sensor Output Level Low

* Check wiring, beam position, sensor.

0 : Upper Center

4 : Upper Left

1 : Middle Left

5 : Upper Right

2 : Middle Right

6 : Lower Left

3 : Lower Center

7 : Lower Right

20

Sensor Output Level High

* Check OP-amp circuit.

0 : Upper Center

4 : Upper Left

1 : Middle Left

5 : Upper Right

2 : Middle Right

6 : Lower Left

3 : Lower Center

7 : Lower Right

30

Adjustment Loop Counter Overflow

* Check the registring information on the convergence board.

40

Regi Data Overflow

* Check the convergence yoke driver ICs.

50

Regi Data Overflow

60

Offset Overflow

* Convergence patterns displayed are out of normal range.

70

Offset Overflow

ERROR

DISCRIPTION

NOTE

CODE

If an error code is displayed after the set has been fully adjusted, correctly, please check the following items: position, tilt and sizing.  If

either of these adjustments are off, even slightly, the auto-registration pattern will not hit the four sensors properly. This occurs when the

internal generator patterns is being flashed on the screen for the sensors to read.  Therefore, auto registration (called auto-focus) cannot

operate properly causing an error code to be displayed. In order for this function to operate properly, correct position, tilt and size must be

adjusted properly.

PJE            2 9             1 4 0
ERR            

ITEM NUMBER-29

ERROR CODE 40

SENSOR NUMBER
(ONLY "10"or "20")

R.G.B

G-0 (Blank)
R-1
B-2

– 56 –

When replacing the following components marked with 

 on

the schematic diagram always check HV regulation, and if nec-
essary re-adjust.

: R8196, R8232
: C8018,C8064, C8066, C8074, C8082

D8042
IC8002, IC8007, IC8008
Q8022
R8093, R8095, R8096, R8105, R8108
R8112, R8113, R8114, R8128, R8136,
R8138, R8139, R8154, R8157, R8168,
R8173, R8174, R8177, R8178, R8195,
R8196, R8232
T8002 (LOT), T8003 (FBT)
HV BLOCK, D BOARD

When replacing the following components marked with 

 on

the schematic diagram always check hold-down voltage and if
necessary re-adjust.

: R8194, R8231
: C8018, D8026, D8032, D8035, D8050

IC8006, IC8009, IC8010
Q8021, Q8031
R8092, R8094, R8097, R8109,R8110,R8115,
R8117,R8118, R8121, R8123, R8125, R8129,
R8135, R8140, R8155, R8190, R8191, R8192,
R8193, R8194, R8198, R8231
T8002 (LOT), T8003(FBT)
HV BLOCK, D BOARD

Remove the cap off from
the unused terminal and
connect a static voltmeter
there.

1. Connect a HV static voltmeter to the unconnected plug of

the high-voltage block.

2. Power on the set.
3. Receive dot signal patterm.
4. Check that the HV static voltmeter is readind 34.0 

±

 0.5kV

dc.

1. Repart step 1 as above.
2. Connect 33k

Ω

 variable resistor, set to maximum value, to

CN8007.

3. Power on the set.
4. Receive dot signal pattern.
5. Gradually lower the value of the variable resistor until the

static voltmeter is reading 34.0 

±

 0.5 kVdc.

6. Switch off the set.
7. Remove the VR connected across CN8007, and measure its

value.

8. Solder a resistor value, nearest to the measured value, across

CN8007.

9. Reconfirm operation check.

1. Connect a HV static voltmeter to the unconnected plug of

the high-voltage block.

2. Connect a 33k

Ω

 variable resistor, set to maximum value,

across CN8008.

3. Power on the set.
4. Receive dot signal pattern.
5. Gradually lower the value of the variable resistor and check

that the hold-down circuit operates at a static voltmeter read-
ing of 31.0 

±

 0.5kV dc when the raster disappears.

1. REPART STEPS 1 ~ 5 as above.
2. Just at the point hold-down circuit begins to operate switch

off the set.

3. Remove the VR connected across CN8008, and measure it’s

resistance.

4. Solder a resistor value, nearest to the measured value, across

CN8008.

5. Reconfirm operation check.

The following adjustments should always be performed
when replacing IC6101.
1. Supply 120.0 

±

 2.0VAC  to variable autotransformer.

2. Receive dot signal pattern and set the PICTURE and

BRIGHTNESS settings to their minimum.

3. Confirm the voltage of TP  +B 135V is less than 137.0Vdc.
4. If step 4 not satisfied , replace IC6101 and repeat above steps.

1. Connect a voltmeter to TP. OVP and ground.
2. Supply 120VAC to variable autotransformer.
3. Power on the Set.
4. Supply 150VDC to TP. OVP.
5. Check the OVP is activated.