Sony KP-57WV600 (serv.man2) Service Manual ▷ View online
— 46 —
KP-57WV600
MODEL NVM DIFFERENCE
������������
������������
����
�������
����
�������
��������������������������������
�
�����������������������������������
�
���������������������������������
�
�����������������������������������
��
���������������������������������
�
�����������������������������������
�
���������������������������������
�
������������������������������������
�
����������������������������������
�
�����������������������������������
�
����������������������������������
�
�����������������������������������
��
������������������������������
�
�����������������������������������
�
������������������������������
��
������������������������������������
�
�������������������������������
�
�������������������������������������
�
�������������������������������
�
�������������������������������������
�
�������������������������������
�
������������������������������������
�
�������������������������������
��
������������������������������������
�
�������������������������������
�
�������������������������������������
�
��������������������������������
�
�������������������������������������
�
��������������������������������
�
���������������������������������
�
���������������������������������
�
���������������������������������
��
���������������������������������
��
��������������������������������
�
���������������������������������
�
������������������������
��
����������������������������������
�
����������������������
��
����������������������������������
�
�����������������������������
�
����������������������������������
�
�����������������������������
�
�������������������������������������
�
����������������
�
�������������������������������������
��
������������������������������
�
�������������������������������������
�
���������������
�
��������������������������������������
�
��������������
�
�������������������������������������
�
��������������������������������������
�
�������������������������������������
��
��������������������������������������
�
�������������������������������������
�
�����������������������������
�
��������������������������������������
�
���������������������������
�
��������������������������������������
�
����������������������������������
�
���������������������������������������
�
����������������������������������
�
���������������������������������������
�
�������������������������������������
�
��������������������������������������
�
�������������������������������������
�
��������������������������������������
�
���������������������������������
�
���������������������
�
���������������������
�
— 47 —
KP-57WV600
MODEL NVM DIFFERENCE
������������
������������
����
�������
����
�������
���������������������
�
�������������
���
���������������������
�
�������������
���
����������������������
�
���������������������
�
���������������������
�
���������������������
�
����������������������
�
����������������������
�
����������������������
�
����������������������
�
����������������������
�
�����������������������
�
�����������������������
�
����������������������
�
����������������������
�
�����������������������
�
�����������������������
�
����������������������
�
�����������������������
�
����������������������
�
�����������������������
�
����������������������
�
����������������������
�
����������������������
�
�����������������������
�
�����������������������
�
����������������������
�
�����������������������
�
�����������������������
�
— 48 —
KP-57WV600
2-12. REGISTRATION ADJUSTMENT
(PJE MODE ONLY)
Change the
wide screen
mode
wide screen
mode
* When the
NTSC Full mode
adjustment has finished,
copy its data to
the next
wide screen
mode the
first time only
and be sure to
adjust in the order given.
adjustment has finished,
copy its data to
the next
wide screen
mode the
first time only
and be sure to
adjust in the order given.
*ADJUSTING FLOW
START
Turn on the power and wait for 10 minutes.
Set to the NTSC Full mode
Check the deflection yokes, the centering magnets,
2 pole/4 pole magnets
Set to the service mode.
MAIN DEFLECTION ADJUSTMENT (Green)
Green coarse adjustment
Green fine adjustment
Red coarse adjustment
Red fine adjustment
Blue fine adjustment
Blue coarse adjustment
Memorize the FLASH FOCUS offset data
(Run flash focus in Service Mode)
End
Another wide screen mode?
DEFLECTION
SUB
ADJUSTMENT
ALLCOPY*
Yes
No
2-12-1.SETUP FOR ADJUSTMENT
MARKING
• At the 4 sides of the screen, locate the middle. Use a tape measure to
• At the 4 sides of the screen, locate the middle. Use a tape measure to
identify the middle.
: middle
DATA SETTING
1. Set NTSC Full mode.
2. Enter the service mode, and select “PJE”.
1. Set NTSC Full mode.
2. Enter the service mode, and select “PJE”.
2-12-2.MAIN DEFLECTION ADJUSTMENT
NOTE: Before this adjustment, refer to section 2-11 for PJE item #78-85
input data.
1. Cover the red and blue CRT lenses with lens caps to allow only green
to show (or use the method shown in the note below for turning off
the CRTs individually without using lens caps).
2. Enter the monoscope signal and set to NTSC Full mode.
3. Enter the service mode, and select “2170D-1”.
4. Adjust “0 VPOS” and “1 VSIZ” so that the picture is displayed in the
3. Enter the service mode, and select “2170D-1”.
4. Adjust “0 VPOS” and “1 VSIZ” so that the picture is displayed in the
center of the screen.
5. Adjust “2VSZ0” for 1080i vertical size adjustment.
0 VPOS
1 V-Size
6. Select “2170D-2” and adjust “2 H-Size” so that the picture size is
within the specification.
2 H-Size
SPEC
Overscan Spec. = 9%
Input Signal
H SIZE
V SIZE
Monoscope
15.6 ± 0.2 sq.
11.5 ± 0.2 sq.
7. Copy the data of the NTSC Full mode to the other wide screen mode
and, if necessary, adjust in the other mode.
— 49 —
KP-57WV600
2-12-3.OPERATION METHOD FOR
PROJECTOR ENGINE MODE
MUTING
Category up
Category up
Adjustment
item up
Adjustment
Adjustment
item down
ENTER
Mode Select
(Course Adjustment
Fine Adjustment)
Test signal select
crosshatch + video
signal dots + video signal
crosshatch + black dots
and black off
Color Select GRN
to BLU to RED
DISPLAY
POWER
Test Reset
Initialize data
(Not stored)
Category
down
MENU
RM-Y188
1. FUNCTION OF KEYS ON COMMANDER
1
1
Changes adjustment item. (Item # moves up)
Marker moves clockwise from center to outside.
(In Fine Adjustment mode)
4
Changes adjustment item. (Item # moves down)
Marker moves counter clockwise from outside to center.
(In Fine Adjustment mode)
2
Changes adjustment category.
(Category # moves up)
5
Changes adjustment category.
(Category # moves down)
Joystick
Changes data value. (Up or down)
Marker moves clockwise from center
(up, down, right, and then left) to outside.
(In Fine Adjustment mode)
3
Changes adjustment color.
GRN àBLU àRED
6
Displays or changes internal test signals.
crosshatch + external signal à
crosshatch + borderline à
crosshatch only à
dot only à off
9
Switches adjustment mode.
Coarse adjustment model à
Fine adjustment mode
Press Switches marker moving method.
Joystick
Joystick
(In Fine Adjustment mode)
Pressing down on the joystick in Fine Adjustment mode switches
between selecting and un-selecting a point.
When a point is selected, the cursor changes to that color to indicate
the point is selected and can be adjusted. If a point is not selected the
cursor is white.
Joystick
5 6 3 4
keys à
1 and 4 buttons
Commander Function
Buttons
Mode
Description
0 + ENTER
READ
Reads data to NVM.
MUTING+ENTER WRITE
Writes data from NVM.
7 + ENTER
PJE
Service data initialization.
Not stored.
Not stored.
INITIAL
(Be sure not to use usually)
2. OPERATION METHOD FOR COARSE ADJUSTMENT
1. Enter the service mode and select “PJE”.
2. Press the “1” or “4” button on the remote commander to select the
2. Press the “1” or “4” button on the remote commander to select the
item, and then use the joystick to change the data.
PJE
00
00
FDIS
Adjustment Item
Item No.
Data
direction:Data up
direction:Data down
Joystick
54
63
3. Select “GRN CENT”. When BLU or RED is displayed, press the “3”
button on the remote commander to change the adjustment color
in the order of GRN àBLU àRED.
4. In the GRN, BLU, or RED mode, move the joystick 5 or 6to
change the data in vertical direction, or 3 or 4 to change the data
in a horizontal direction.
5
4
3
6
GRN
000
000
CENT
Adjustment Item
Data (H)
Data (V)
Color
: Data (H) up
: Data (H) down
: Data (V) up
: Data (V) down
: Data (V) up
: Data (V) down
5. Before returning to the service mode, press the “MUTING” +
“ENTER” buttons on the remote commander to write the data.
(You must complete step 5 to write the data. If you omit step 5 the
set data is returned to the data prior to the adjustment.)
Click on the first or last page to see other KP-57WV600 (serv.man2) service manuals if exist.