DOWNLOAD Sony KP-51WS500 / KP-57WS500 / KP-65WS500 Service Manual ↓ Size: 9.74 MB | Pages: 127 in PDF or view online for FREE

Change the
display mode

* When the 

NTSC Full mode
adjustment has finished,
copy its data to 
the next 
display mode the 
first time only 
and be sure to 
adjust in the order given.

*ADJUSTING FLOW

START

Turn on the power and wait for 10 minutes.

Set to the NTSC Full mode

Check the deflection yokes, the centering magnets,

2-pole/4-pole magnets

Set to the service mode.

MAIN DEFLECTION ADJUSTMENT (Green)

Green coarse adjustment

Green fine adjustment

Red coarse adjustment

Red fine adjustment

Blue fine adjustment

Blue coarse adjustment

Memorize the FLASH FOCUS offset data

End

Another display mode?

DEFLECTION

SUB 

ADJUSTMENT

ALLCOPY*

Yes

No

•  At the 4 sides of the screen, use a tape measure to locate the middle. 

: middle

DATA SETTING
1. Set NTSC Full mode.
2. Enter the service mode, and select “PJE”.

NOTE: Before this adjustment, refer to section 2-11 for PJE input data 
items #78-85.

1.  Cover the red and blue CRT lenses with lens caps to allow only green 

to show (or use the method shown in the note below for turning off the 
CRTs individually without using lens caps).

2.  Enter the monoscope signal and set to NTSC Full mode.
3.  Enter the service mode, and select “2150D-1”.
4.  Adjust “0 VPOS” and “1 VSIZ” so that the picture is displayed in the 

center of the screen.

5.  Adjust “2VSZ0” for 1080i vertical size adjustment.

0 VPOS

1 V-Size

6.  Select “2150D-2” and adjust “2 H-Size” so that the picture size is 

within the specifi cation.

2 H-Size

SPEC

Overscan Spec. = 9%

Input Signal

H SIZE

V SIZE

Monoscope

15.6 ± 0.2 sq.

11.5 ± 0.2 sq.

7.  Copy the data of the NTSC Full mode to the other display mode and, 

if necessary, adjust in the other mode.

MUTING

Category up
Adjustment 
item up

Adjustment 
item down

ENTER

Mode Select 
(Course Adjustment 
Fine Adjustment)

Internal Test signal

Color Select GRN 
to BLU to RED

DISPLAY

POWER

VOLUME +

Initialize data
(Not stored)

Category 
down

MENU
Data Up/
Down

RM-Y909

1   Changes adjustment item. (Item # moves up)

    

Marker moves clockwise from center to outside. 

  

(In Fine Adjustment mode) 

4   Changes adjustment item. (Item # moves down)

    

Marker moves counter clockwise from outside to center. 

  

(In Fine Adjustment mode) 

2   Changes adjustment category. 

  

(Category # moves up)

5   Changes adjustment category. 

  

(Category  #  moves  down)

Joystick  Changes data value. (Up or down)
    

Marker moves clockwise from center 

  

(up, down, right, and then left) to outside. 

  

(In Fine Adjustment mode) 

3   Changes adjustment color.

  

GRN  ÆBLU ÆRED 

6   Displays or changes internal test signals.

  

 

crosshatch 

+ 

external 

signal 

Æ

 

  

crosshatch  +  borderline  Æ 

  

crosshatch  only  Æ 

  

dot  only  Æ off

9   Switches adjustment mode.

  

Coarse adjustment model Æ 

  

Fine adjustment mode 

Switches marker moving method.

Joystick  (In Fine Adjustment mode) 
 Joystick 

5 6 3 4

keys Æ 1 and 4 buttons

Buttons

Mode

Description

0 + ENTER

READ

Reads data to NVM.

MUTING+ENTER WRITE

Writes data from NVM.

7 + ENTER

PJE

Service data initialization. 
Not stored.

INITIAL

(Be sure not to use usually)

1.  Enter the service mode and select “PJE”.
2.  Press the “1” or “4” button on the remote commander to select the 

item, and then use the joystick to change the data.

PJE

00

00

FDIS

Adjustment Item

Item No.

Data

direction:Data up

direction:Data down

Joystick

54
63

3.  Select “GRN CENT”. When BLU or RED is displayed, press the “3” 

button on the remote commander to change the adjustment color 
in the order of GRN ÆBLU ÆRED.

4.  In GRN, BLU, or RED mode, move the joystick 

5 or 6to change 

the data in vertical direction, or 

3 or 4 to change the data in a 

horizontal direction.

5

4

3

6

GRN

000

000

CENT

Adjustment Item

Data (H)

Data (V)

Color

: Data (H) up

: Data (H) down

: Data (V) up

: Data (V) down

5.  Before returning to the service mode, press the “MUTING” + 

“ENTER” buttons on the remote commander to write the data. 
(You must complete step 5 to write the data. If you omit step 5 the 
set data is returned to the data prior to the adjustment.)

1.  Enter the service mode and select “PJE”.
2.  Select FDIS and set the data to “01” so that the data at each 

position can be displayed in fi ne adjustment mode.

3.  Press the “9” button on the remote commander and fi ne 

adjustment mode will be active where a green marker appears in 
the center of the screen. (In the case of GRN mode)

4.  Press down on the joystick, and the marker color will be alternately 

switched between green (GRN mode) and white.

5.  Press the “1” or “4” button on the remote commander, or use the 

joystick to move the marker to the position to be adjusted, where 
fi ne adjustment can be made.

*  When the marker color is white: 

(in this case, fi ne adjustment is disabled)

Use the joystick to move the marker up, down, left, or right.

*  When the marker color is green: 

(GRN mode)

1   : Moves the marker clockwise from the center to the outside.
4   : Moves the marker counter clockwise from the outside

  to the center.

*  Fine adjustment can be made on the basis of a marker position 

using the joystick to move 

5 6 3 

or

4

.

CROSSHATCH

Move joystick 5 direction

Move joystick

 4 direction

CROSSHATCH

6.  Press the “9” button on the remote commander to return to coarse 

adjustment mode.

  

Adjustment 

type

Adjustment item 

G 

R 

B

   H/V* 

H/V* 

H/V*

CENT  

O/O  O/O  O/O

SKEW  

O/O  O/O  O/O

SIZE  

O/O O/O O/O

LIN  

O/O 

O/O 

O/O

KEY  

-/O -/O -/O

PIN  

 

O/O 

O/O 

O/O

MLIN  

O/-  O/-  O/-

MSIZ 

 

O/- 

O/- 

O/   

* H = Horizontal  V = Vertical    O = Yes       = No

Note: If the value is over the limit value, adjust these in the fi ne 
adjustment mode.
        Coarse Data Limit Value:

CENT H   

 

35 ± 170V

CENT V 

 

 

20 ± 170V

SIZE H 

 

 

-75 MAX

BLUE H LIN 

 

-425 MIN

RED H LIN 

 

 425 MAX

•  The adjustment should be done in the numerical order given.

1.  Cover the red and blue CRT lenses with lens caps to allow only green 

to show (or use the method shown in the note below for turning off the 
CRTs individually without using lens caps).

Note: If lens caps are unavailable, you can cut off the unnecessary color 
beams by controlling the service mode 2150P-2 1 RGBS.

2.  Enter the monoscope signal to set. 
3.  Select the PJE mode.
4.  Press the “6” button on the remote commander to display the internal 

test signal (crosshatch).

5.  Select “GRN CENT”, and adjust so that the pictures coincide in the 

center of screen.

Push the joystick 

to

Push the joystick 

to

Push the joystick 

to

Push the joystick 

to

7.  Select “GRN SKEW”, and correct the tilt of horizontal lines and 

vertical lines.

Push the joystick 

to

Push the joystick 

to

Push the joystick 

to

Push the joystick 

to

8.  Select “GRN SIZE”, and adjust so that each distance from center to 

left end and to right end is equal. Adjust so that each distance from 
center to top and to bottom is equal.

Push the joystick 

to

Push the joystick 

to

Push the joystick 

to

Push the joystick 

to

9.  Select “GRN LIN”, and adjust so that each space at the right end and 

at the left end of screen is equal. Adjust so that each space at the top 
and at the bottom of screen is equal.

Push the joystick 

to

Push the joystick 

to

Push the joystick 

to

Push the joystick 

to

10. Select “GRN MSIZ”, and correct the space intervals for the horizontal 

section so the screen is equal. 

Push the joystick 

to

Push the joystick 

to

11. Select “GRN MLIN”, and correct the sizes of the horizontal line so the 

center of the screen is symmetrical left and right.

Push the joystick 

to

Push the joystick 

to

Note: The SIZE and LIN, MSIZ and MLIN adjustments 

      affect each other. If necessary, adjust these mutually.

12. Select “GRN PIN”, and adjust so that right and left vertical lines on 

the screen become straight. Adjust so that upper and lower horizontal 
lines on the screen become straight.

Push the joystick 

to

Push the joystick 

to

Push the joystick 

to

Push the joystick 

to

13. Select “GRN KEY”, and adjust so that upper and lower horizontal 

lines on the screen become parallel.

Push the joystick 

to

Push the joystick 

to

Note: The VPIN and KEY adjustments affect each other.

      If necessary, adjust these mutually.

14. Press the “9” button on the remote commander to enter fi ne 

adjustment mode.