DOWNLOAD Sony KP-48V80 / KP-53V80 / KP-61V80 Service Manual ↓ Size: 10.79 MB | Pages: 105 in PDF or view online for FREE

– 37 –

1

 Nineteen screws(KP-53V80) 

     Twenty three screws 
     (KP-61V80)
     Twenty four screws (KP-48V80)
     (Screw(4x20), tapping

2

 Mirror cover

1

 Five screws (KP-53V80/61V80)

     Three screws (KP-48V80)
    (Screws(4x20), tapping)

2

 Fourteen screws (KP-61V80)

     Fifteen screws (KP-53V80)
     Twelbe screws (KP-48V80)
     (Screws(4x20), tapping)

3

 Beznet assy

3

 HC board

2

 L screen holder

6

 Clows

7

 S board

Sensor 
bracket (B)

4

 Two screws

    (+BVTP 4x12)

1

 Two screws

    (+BVTP 4x12)

5

 Two screws

    (+BVTP 4x12)

Sensor 
bracket (A)

2

 Seven screws

    (+BVTP 3x12)

3

 Terminal board

4

 U board

1

 Two screws

    (Screws (4x20), tapping)

– 38 –

4

 Two screws

    (+BVTP 3x12)

1

 Eight screws

    (+BVTP 3x12)

3

 G board

6

 A board

5

 Claw

2

 Claws

Main bracket

4

 Four screws

     (Screw(4x20), tapping)

!º

 Four screws

    (+BVTP 4x12)

!¡

 Picture tube

Picture tube

8

 Diflection yoke

9

 Tension

     spring

2

 Four screws

    (Screw(4x20), tapping)

3

1

 Four screws

    (Screw(4x20), tapping)

7

 Neck assy

6

 CR board

5

 Lens

Lens

CAUTION: Removing the arrow-marked

screws is strictly prohibited.
If removed, it may cause liquid spill.

(1) Remover

1

 Rubber cap

2

 HV cable

   turn 90

°

1

 HV cable

Gutter

Hook

(2) Installation

– 39 –

1. Receive the Monoscope signal.

2. Set 50% BRIGHTNESS and minimum PICTURE.

3. Turn the red VR on the FOCUS block all the way to the left

and then gradually turn it to the right until the point where you

can see the retrace line.

4. Next gradually turn it to the left to the position where the

retrace line disappears.

10. Set VPNT 28 RON to “000”, 29 GON to “000” and 30 BON

to “001” to show only the blue color.

11. Adjust blue CRT lens just the same as green.

*

: Every time you press 6, the test signal changes to

“crosshatch+video signal” - “dots+video signal” -
“crosshach(black)” - “dots(black)” - off.

1. Select VIDEO1 mode without signals.

2. Connect an oscilloscope to the TP701(KR), TP732(KG) and

TP761(KB) of CR board, CG board and CB board.

3. Adjust  R, G and B screen voltage to 170 – 173V with screen

VR on the Focus block.

1. Set to the service mode.

2. Change TV mode to the video input mode.

3. Set to PJE, and press 6 to display the test signal (crosshatch)

on the screen.

4. Set VPNT 28 RON to “000”, 29 GON to “001” and 30 BON

to “000” to show only the green color.

5. Turn the green VR on the focus block to adjust to the optimum

focus point with the test signal.

6. Set VPNT 28 RON to “001”, 29 GON to “000” and 30 BON

to “000” to show the red color.

7. Turn the red VR on the focus block to adjust to the optimum

focus point with the test signal.

8. Set VPNT 28 RON to “000”, 29 GON to “000” and 30 BON

to “001” to show the blue color.

9. Turn the blue VR on the focus block to adjust to the optimum

focus point with the test signal.

R

G

B

SCREEN

R

G

B

FOCUS

FOCUS block

170 – 173V

GND

pedestal level

In this adjustment, use the remote commander in the
service mode.
For details of the usage of the service mode and the remote
commander, please refer the item 3-9. ELECTRICAL
ADJUSTMENT BY REMOTE COMMANDER.

1. Loosen the lens screw.

2. Set to the service mode.

3. Change TV mode to the video input mode.

4. Set to PJE, and press 6 to display the test signal (crosshatch)“

on the screen.

5. Set VPNT 28 RON to “000”, 29 GON to “001” and 30 BON

to “000” to show only the green color.

6. Turn the green lens to adjust to the optimum focus point with

the test signal.

7. Tighten the lens screw.

8. Set VPNT 28 RON to “001”, 29 GON to “000” and 30 BON

to “000” to show only the red color.

9. Adjust red CRT lens just the same as green.

A

B

Lens

Minimize both A and B.

Center of crosshatch

Scanning line visible.

Test signal

– 40 –

1. Receive the Monoscope signal.

2. Set in service mode.

3. Set VPNT 29 GON to “001” 28 RON to “000” and 30 BON to

“000” to show only the green color.

4. Loosen the deflection yoke set screw and align the tilt of the

Deflection Yoke so that the bars at the center of the

monoscope pattern are horizontal.

5. After aligning the deflection yoke, fasten it securely to the

funnel-shaped portion (neck) of the CRT.

6. The tilt of the deflection yoke for red is aligned  in the mode

VPNT 28 RON “001”,  29 GON “000”, 30 BON “000” on the

service mode menu, and the tilt of the deflection yoke for biue

is aligned with in the mode VPNT 28 RON “000”,  29 GON

“000”, 30 BON “001” on the service menu, is aligned the

same as was done for green.

1. Receive the Dot signal.

2. Set in service mode.

3. Set VPNT 29 GON to “001” 28 RON to “000” and 30 BON to

“000” to show only the green color.

4. Turn the green VR on the focus block to the left and set to

underfocus to enlarge the spot.

5. Now align the 4-Pole Magnet so that the enlarged spot

becomes a perfect circle for green and red.

6. Perform the same alignment for blue.

1. Select the video menu and set the mode to “Vivid” mode.

2. Set to the service mode.

3. Change TV mode to the video input mode.

4. Set to PJE, and press 6 to display the test signal (dots) on the

screen.

5. Turn the blue VR on the focus block to adjust to the diameter

of the dots as shown in the figure below.

2-pole magnet

4-pole magnet

Deflection yoke

Anode cap

1. Receive the Dot signal.

2. Set in service mode.

3. Set VPNT 29 GON to “001” 28 RON to “000” and 30 BON to

“000” to show only the green color.

4. Turn the green VR on the focus block to the right and set to

overfocus to enlarge the spot.

5. Now align the 2-Pole Magnet so that the enlarged spot is in the

center of the Just Focus spot.

6. Align the green focus VR and set for just (precise) focus.

7. Perform the same alignment for red.

Use the center dot

/

x

y

x : y = 1:1.5 (BIue)
x : y = 1:1 (Green, Red)

Use the center dot

Lmm Max

Inch

L

48"

7

53"

8

61"

9