Sony KP-44PS2 / KP-44PS2U / KP-51PS2 Service Manual ▷ View online
– 5 –
KP-44PS2/44PS2U/51PS2
RM-903
1-2. ERROR DETECTION MONITOR
Device acknowledge is used to check IIC errors. Device acknowledge is checked by sending an IIC start sequence during CRT power
on. Each device is checked three times, if there is no acknowledge after each attempt, it will be regarded as an error.
There are three steps to check for errors.
1. IIC line 0
If all devices except the NVM have errors, IIC line 0 error is displayed.
2. Board check
If all devices mounted on one board have errors, board error is displayed.
3. Each device check
if IIC line error and board error are not detected then the device with an error is displayed.
The detected errors can be displayed as follows:
1. Error Monitor Menu
2. Error Reader
1-2-1. Error Monitor Menu
The error monitor menu is displayed by selecting TT33. The following menu will be displayed:
Error Monitor
1
Operating Time :
Stored Errors :
1. A-Board
Current Error :
Start Error Sequence
2. B3-B CXA2100 MID
3. J-B CXA2123 Main Col Dec
4. Error Code Not Valid
5. Error Code Not Valid
3. J-B CXA2123 Main Col Dec
4. Error Code Not Valid
5. Error Code Not Valid
Ignore Errors
OFF
000021 h 40 min
ON
ON
– 6 –
KP-44PS2/44PS2U/51PS2
RM-903
1-2-2. Error Reader Display
The error reader display is connected to the service connector to read actual error codes. The part number for the error reader display
is S-188-900-10.
Once an error has been detected it will then be displayed on the two digit error reader. The errors displayed refer to the following table:
Send Data to Error Reader
Error Code
Data High
Data Low
Error Type
Function
00 00h
–
f0h
no device
Gen. IIC Error
00 01h
f0h
01h
IIC 0 line
00 02h
f0h
02h
IIC 1 line
not used
Board Error
01 00h
f1h
00h
A Board
04 00h
f4h
00h
B3 Board
06 00h
f6h
00h
E Board
07 00h
f7h
00h
J/S Board
08 00h
f8h
00h
M Board
Device Error
A Board
01 01h
f1h
01h
CXA1875
Port Expander
01 02h
f1h
02h
TU1301
Main Tuner
01 03h
f1h
03h
TU1302
Sub Tuner
B3 Board
04 01h
f4h
01h
CXD9509
MID
E Board
06 01h
f6h
01h
CXA2100
Backend
J Board
04 04h
f4h
04h
TDA9178
Picture Booster
07 01h
f7h
01h
CXA2057
Auto Wide
07 03h
f7h
03h
CXA2123
Sub Colour
07 04h
f7h
04h
CXA2123
Main Colour
07 0Ah
f7h
0Ah
CXA2149
AV SW
S Board
07 05h
f7h
05h
CXA1875
Sub Sound
07 08h
f7h
08h
MSP3410D
Sound Proc
M Board
08 01h
f8h
01h
ST24C32
NVM
–
7
–
–
SECTION 2
GENERAL
The operating instructions mentioned here are partial abstracts
from the Operating Instruction Manual. The page numbers of
the Operating Instruction Manual remain as in the manual.
from the Operating Instruction Manual. The page numbers of
the Operating Instruction Manual remain as in the manual.
5
GB
One Remote Control
(RM-903)
Overview of TV Buttons
Checking the Accessories Supplied
Overview
Two batteries (R6 type)
Overview
s
Programme up
or down buttons
(selects TV channels)
or down buttons
(selects TV channels)
On
/Off Switch
Selecting
input source
Auto
Convergence
button
Volume control
buttons
Press on the mark
, on the front
of the projection TV to reveal the front
buttons.
Standby indicator
S Video
Input jack
Video Input
jack
Audio Input
jacks
Headphone
jack
6
S
RM 903
PROGR
MENU
1
4
7
2
5
8
0
3
6
9
K
VIDEO
TV
VIDEO
TV
VTR 1 2 3 4 DVD
CH
Overview
Overview of Remote Control Buttons
Resetting to factory set levels
Press the to return the picture and sound
settings to factory set levels. This will also
return the set to the install condition, the
“Auto Tuning” menu will appear on the
screen, refer to the section “Switching on the
set and automatically Tuning” (step 4) of this
manual.
Press the to return the picture and sound
settings to factory set levels. This will also
return the set to the install condition, the
“Auto Tuning” menu will appear on the
screen, refer to the section “Switching on the
set and automatically Tuning” (step 4) of this
manual.
VCR on/off
Press to switch your VCR on or off.
Press to switch your VCR on or off.
Muting the Sound
Press to mute TV sound.
Press again to restore the sound.
Press to mute TV sound.
Press again to restore the sound.
Selecting TV mode
Press to switch off Teletext or video input.
Press to switch off Teletext or video input.
PAP (Picture And Picture)
For more details, please refer to the section
"Using PAP (Picture And Picture)".
For more details, please refer to the section
"Using PAP (Picture And Picture)".
Selecting Teletext
Press to switch on Teletext.
Press to switch on Teletext.
Displaying EPG
Press to display the Electronic Programme
Guide (EPG). Press again to switch off EPG.
Press to display the Electronic Programme
Guide (EPG). Press again to switch off EPG.
Freezing the picture
Press to freeze the picture. Press again to
return to the normal picture.
Press to freeze the picture. Press again to
return to the normal picture.
Selecting channels
Press to select channels.
Press to select channels.
For double-digit programme numbers, e.g.
23, press -/-- first, then the buttons 2 and 3.
If you enter an incorrect first digit, this
should be corrected by entering another digit
(0-9) and then selecting -/-- button again to
enter the programme number of your choice.
23, press -/-- first, then the buttons 2 and 3.
If you enter an incorrect first digit, this
should be corrected by entering another digit
(0-9) and then selecting -/-- button again to
enter the programme number of your choice.
Selecting Sound mode
Press repeatedly to change the sound mode.
Press repeatedly to change the sound mode.
Selecting Picture mode
Press repeatedly to change the picture mode.
Press repeatedly to change the picture mode.
Adjusting TV Volume
Press to adjust the volume of the TV.
Press to adjust the volume of the TV.
Displaying the time
Press to switch the time on or off
(available only when teletext is
broadcast).
Press to switch the time on or off
(available only when teletext is
broadcast).
VCR operation
For more details, please refer to the
section "Remote Control of other
Sony Equipment".
For more details, please refer to the
section "Remote Control of other
Sony Equipment".
Besides TV functions, all coloured buttons as well as green
symbols are also used for Teletext operation. For more details,
please refer to the "Teletext" section of this instruction manual.
symbols are also used for Teletext operation. For more details,
please refer to the "Teletext" section of this instruction manual.
Overview
To Temporarily Switch Off
Press to temporarily switch off TV (the standby
indicator
Press to temporarily switch off TV (the standby
indicator
on the set lights up in red). Press
again to switch on TV from standby mode.
After 15-30 minutes without a signal and
without any button being pressed, the set
switches automatically into standby mode.
switches automatically into standby mode.
Displaying On Screen Information
Press to display all on-screen indications.
Press again to cancel.
Press to display all on-screen indications.
Press again to cancel.
Selecting Input source
Press repeatedly until the desired input symbol of
the source appears on the screen.
Press repeatedly until the desired input symbol of
the source appears on the screen.
Back to the channel last watched
Press to watch the last channel selected (watched for
at least 5 seconds).
Press to watch the last channel selected (watched for
at least 5 seconds).
Selecting Screen format
Press repeteadly to change the format of the screen
(for more details, please refer to the section
“Changing the Screen format”).
Press repeteadly to change the format of the screen
(for more details, please refer to the section
“Changing the Screen format”).
Displaying Multi PIP (Picture In Picture)
Press to display Multi PIP mode. Press again to
cancel.
Press to display Multi PIP mode. Press again to
cancel.
Joystick for menu selection
• When MENU is switched on:
• When MENU is switched on:
4
Scroll Up
$
Scroll Down
Z
Previous menu or selection
z
Next menu or selection
OK Confirms your selection
• When MENU is switched off:
Z
Return to the last menu screen.
OK Shows a channel overview
Selecting channels
Press to select the next or previous channel.
Press to select the next or previous channel.
Displaying the menu system
Press to display the menu on the screen. Press again
to remove the menu display from the screen.
Press to display the menu on the screen. Press again
to remove the menu display from the screen.
–
8
–
–
8
First Time Operation
The first time you switch on your TV, a sequence of menu screens appear on the TV enabling you to 1) choose the language
of the menu screen, 2) choose the country in which you wish to operate the set, 3) search and store all available channels
of the menu screen, 2) choose the country in which you wish to operate the set, 3) search and store all available channels
(TV Broadcast) and 4) change the order in which the channels (TV Broadcast) appear on the screen.
However, if you need to change the language menu, change the country, change or repeat the tuning (e.g. when you move
However, if you need to change the language menu, change the country, change or repeat the tuning (e.g. when you move
house) or rearrange the order of the channels, you can do that by selecting the appropriate menu in the
(Set Up)
.
Switching on the set and Automatically Tuning
1
Connect the set plug to the mains socket (220-240V AC, 50 Hz). Press
the
on
/off button on your set to switch on. The first time you press
this button the Language/Country menu displays automatically on
the screen.
the screen.
2
Push the joystick on the remote control
$ or 4 to select the language,
then press OK to confirm your selection. From now on all the menus
will appear in the selected language.
will appear in the selected language.
3
Push the joystick
$ or 4 to select the country in which you will
operate the set, then press OK to confirm your selection.
If the country in which you want to use the TV set does not
appear in the list, select “-” instead of a country.
appear in the list, select “-” instead of a country.
If you are operating the projection TV in the UK, we
reccommend you not to select "Off". Otherwise the On Screen
reccommend you not to select "Off". Otherwise the On Screen
clock will not show the correct UK time.
4
The Auto Tuning menu appears on the screen in the selected
language, then press the OK button on the remote control to select
Yes
Yes
.
5
A new menu appears automatically on the screen asking you to
check that the aerial is connected. Confirm that the aerial is connected
check that the aerial is connected. Confirm that the aerial is connected
and then press the OK button to start the automatic tuning.
• The TV starts to automatically search and store all available
channels (TV Broadcast) for you.
• If you have selected the “Off” option in the Country menu and
you activate autotuning again, the TV Broadcasts will be
stored from the programme number selected at that time.
stored from the programme number selected at that time.
This procedure could take some minutes. Please, be patient and
do not press any button. Otherwise the automatic tuning will
not be completed.
do not press any button. Otherwise the automatic tuning will
not be completed.
continued...
First Time Operation
Language/Country
Language
Country
Select Language:
Confirm: OK
4
Italiano
Français
Español
English
Deutsch
Dansk
Č
e
š
tina
Language/Country
Language
Country
Select Language:
Confirm: OK
4
Italiano
Français
Español
Français
Español
English
Deutsch
Dansk
Č
e
š
tina
Language/Country
Language
Country
Select Language:
Confirm: OK
4
Italiano
Français
Español
English
Deutsch
Dansk
Č
e
š
tina
Language/Country
Language
Country
Select Country:
Confirm: OK
4
Finland
Denmark
Czech Rep.
Bulgaria
Belgium
Belgium
Austria
Off
Do you want to start
automatic tuning?
automatic tuning?
Yes: OK No:
Please confirm that
aerial is connected!
aerial is connected!
Yes: OK No:
1
2
3
4
5
2
3
4
5
CO2
CO3
CO4
CO7
CO8
CO3
CO4
CO7
CO8
Searching...
S
RM 903
PROGR
MENU
1
4
7
2
5
8
0
3
6
9
TV
VIDEO
7
GB
Installation
Make sure you insert the batteries using the correct
polarities.
polarities.
Always remember to dispose of used batteries in an
environmental friendly way.
environmental friendly way.
Inserting Batteries into the Remote Control
Connecting cables are not supplied.
Connecting the Aerial and VCR
or
VCR
The Scart lead is optional.
If you use this optional connection it can improve picture and sound quality when using a VCR.
If you use this optional connection it can improve picture and sound quality when using a VCR.
If you do not use a SCART lead, after automatically tuning the projection TV refer to the "Manually Tuning the TV"
section of this instruction manual, to tune in the set to the output of your VCR. Also refer to your VCR instruction manual
to find out how to find the output channel of your VCR.
section of this instruction manual, to tune in the set to the output of your VCR. Also refer to your VCR instruction manual
to find out how to find the output channel of your VCR.
OUT
IN
Installation
Click on the first or last page to see other KP-44PS2 / KP-44PS2U / KP-51PS2 service manuals if exist.