DOWNLOAD Sony KP-44DX2U Service Manual ↓ Size: 23.15 MB | Pages: 110 in PDF or view online for FREE

(1) Removal

(2) Installation

Rubber cap

1

HV cable

turn 90

2

Rubber cap

1

HV cable

2

Hook

3

Gutter

4

Screw

(+BVTP 3x12)

4

Six screws

(+BVTP 3x12)

2

Printed circuit

board support

1

Claw

7

AP board

6

Screw

(+BVTP 3x12)

4

D board

3

Three claws

5

Five screws

(hexagon head)

3

Four screws

(Hexagon head)

4

Beznet block

2

Eleven screws

(+BVTP 4x16)

1

Five claws

1

G board

2

Six screws

(BVTP 4x16)

2

Terminal board

1

Picture tube

6

Deflection yolk

5

Neck assembly

4

CR board

3

Four screws

(+BVTP 4x16)

7

Four screws

(Hexagon head)

1

Lens

2

Removing the arrow-marked screw is strictly inhibited.
If removed, it may cause liquid spill

Screw

(Hexagon head)

3

Two screws

(Hexagon head)

1

Three screws

(Hexagon head)

2

Chassis block

4

Screw

(Hexagon head)

3

Two claws

3

screw

(+BVTP 3x12)

1

A board

2

1.

Turn on the power of the set.

2.

Select VIDEO1 mode without signals.

3.

Supply DC 175 ±0.5 V from external power supply to
TP7103 (KR), TP7203 (KG) or TP7303 (KB) of CR board,
CG board and CB board.

4.

Adjust red, green and blue screen voltage, with SCREEN
VR on the focus pack until retrace line disappears .

1.

Receive the Monoscope signal.

2.

Place the caps on the red and blue lens so that only the
green color is shown.

3.

Loosen the deflection yoke set screw and align the tilt of
the Deflection yoke so that the bars at the center of
the monoscope pattern are horizontal.

4.

After aligning the deflection yoke, fasten it securely to
the funnel-shaped portion (neck) of the CRT.

5.

The tilt of the deflection yoke for red and blue is aligned
the same as was done for green.

Neck Assy

Make sure deflection yoke is 
touching CRT closely.

2-pole magnet

4-pole magnet

Deflection yoke

Anode cap

R

G

SCREEN

B

R

G

FOCUS

Focus Pack

B

Minimize both A and B.

A

B

5.

Rotate the green lens and align to obtain the best lens
focus at the center area.

6.

Rotate the green focus VR on the focus pack and align to
obtain the best electrical focus at the centre area.

7.

Perform the same alignment for red and blue lenses and
electric focus.

8.

Fix lens screw.

1.

Receive the Monoscope signal.

2.

Set 50% BRIGHTNESS and minimum PICTURE.

3.

Turn the red VR on the focus pack all the way to the left
and then gradually turn it to the right until the point where
you can see the retrace line.

4.

Next gradually turn it to the left to the position where the
retrace line disappears.

1.

Loose the lens screw.

2.

Program Remote Commander for operation in Service
mode (See Page 23).

3.

Place the caps on the red and blue lens so that only the
green color is shown.

4.

Press “VIDEO” “VIDEO” “5” “6” on the remote
commander to enter 'Projector Engine'. Press “6” twice
on the Commander to display the test signal (crosshatch)
on the screen.