Sony KP-41PX2 Service Manual ▷ View online
– 17 –
KP-41PX2
RM-938
3-6.
BEZNET BLOCK REMOVAL
2
1
1
3
Beznet assembly
Four screws
(Hexagon head)
Five screws
(+BVTP 4x16)
3-7.
TERMINAL BOARD REMOVAL
2
1
Terminal board
Six screws
(BVTP 4x16)
Six screws
(+BVTP 4x16)
– 18 –
KP-41PX2
RM-938
3-8.
AP AND D BOARD REMOVAL
3-9.
G BOARD REMOVAL
1
2
G board
Five claws
2
1
8
7
6
Three claws
Screw
(+BVTP 3x12)
Screw
(+BVTP 3x12)
Screw
(+BVTP 3x12)
Printed circuit
board support
6
4 AP board
Claw
3
D board
5
DS board
– 19 –
KP-41PX2
RM-938
3-10. A BOARD REMOVAL
1
3
A board
Screw
(+BVTP 3x12)
Two claws
2
4
3
1
2
3-12. PICTURE TUBE REMOVAL
6
Four screws
(+BTVP 4x16)
5
7
Removing the arrow-marked screw is strictly inhibited.
If removed, it may cause liquid spill.
Four screws
(+BTVP 4x16)
Lens
CR(CB, CG) board
Neck assembly
Deflection yolk
Picture tube
3-11. HIGH_VOLTAGE CABLE REMOVAL
AND INSTALLATION
4
M2 board
1
2
1
2
(1) Removal
(2) Installation
3
4
Rubber cap
Rubber cap
HV cable
turn 90
HV cable
Hook
Gutter
– 20 –
KP-41PX2
RM-938
Fig. 4-1
4-3. SCREEN (G2) ADJUSTMENT
1.
Turn on the power of the set.
2.
Select VIDEO1 mode without signals.
3.
Supply DC 175 ±0.5 V from external power supply to
TP7103 (KR), TP7203 (KG) or TP7303 (KB) of CR board,
CG board and CB board.
TP7103 (KR), TP7203 (KG) or TP7303 (KB) of CR board,
CG board and CB board.
4.
Adjust red, green and blue screen voltage, with SCREEN
VR on the focus pack until retrace line disappears .
VR on the focus pack until retrace line disappears .
4-4. DEFLECTION YOKE TILT ADJUSTMENT
1.
Receive the Monoscope signal.
2.
Place the caps on the red and blue lens so that only the
green color is shown.
green color is shown.
3.
Loosen the deflection yoke set screw and align the tilt of
the Deflection yoke so that the bars at the center of
the monoscope pattern are horizontal.
the Deflection yoke so that the bars at the center of
the monoscope pattern are horizontal.
4.
After aligning the deflection yoke, fasten it securely to
the funnel-shaped portion (neck) of the CRT.
the funnel-shaped portion (neck) of the CRT.
5.
The tilt of the deflection yoke for red and blue is aligned
the same as was done for green.
the same as was done for green.
Fig. 4-5
Neck Assy
Make sure deflection yoke is
touching CRT closely.
touching CRT closely.
2-pole magnet
4-pole magnet
Deflection yoke
Anode cap
R
G
SCREEN
B
R
G
FOCUS
Focus Pack
B
Fig. 4-4
Lens
Fig. 4-3
Fig. 4-2
Test signal
Minimize both A and B.
A
B
5.
Rotate the green lens and align to obtain the best lens
focus at the center area.
focus at the center area.
6.
Rotate the green focus VR on the focus pack and align to
obtain the best electrical focus at the centre area.
obtain the best electrical focus at the centre area.
7.
Perform the same alignment for red and blue lenses and
electric focus.
electric focus.
8.
Fix lens screw.
SECTION 4 SET-UP ADJUSTMENTS
4-1. SCREEN VOLTAGE ADJUSTMENT
(ROUGH ALIGNMENT)
1.
Receive the Monoscope signal.
2.
Set 50% BRIGHTNESS and minimum PICTURE.
3.
Turn the red VR on the focus pack all the way to the left
and then gradually turn it to the right until the point where
you can see the retrace line.
and then gradually turn it to the right until the point where
you can see the retrace line.
4.
Next gradually turn it to the left to the position where the
retrace line disappears.
retrace line disappears.
4-2. FOCUS ROUGH ADJUSTMENT
1.
Loose the lens screw.
2.
Program Remote Commander for operation in Service
mode (See Page 23).
mode (See Page 23).
3.
Place the caps on the red and blue lens so that only the
green color is shown.
green color is shown.
4.
Press “VIDEO” “VIDEO” “5” “6” on the remote
commander to enter 'Projector Engine'. Press “6” twice
on the Commander to display the test signal (crosshatch)
on the screen.
commander to enter 'Projector Engine'. Press “6” twice
on the Commander to display the test signal (crosshatch)
on the screen.
Click on the first or last page to see other KP-41PX2 service manuals if exist.