DOWNLOAD Sony KLV-S19A10 / KLV-S23A10 Service Manual ↓ Size: 12.1 MB | Pages: 124 in PDF or view online for FREE

US Model

Canadian Model

KLV-S19A10

KLV-S23A10

American TV standard

VHF: 2-13/UHF: 14-69/CATV: 1-125

75-ohm external terminal for VHF/UHF

KLV-S19A10: 19 inches
KLV-S23A10: 23 inches

LCD (Liquid Crystal Display) Panel

 ×

KLV-S19A10: 1,280 dots 

 ×

 768 lines

KLV-S23A10: 1,366 dots 

 ×

 768 lines

S VIDEO (4-pin mini DIN):

Y: 1.0 Vp-p, 75 ohms unbalanced, sync 

negative

C: 0.286 Vp-p (Burst signal), 75 ohms

VIDEO:

1 Vp-p, 75 ohms unbalanced, sync negative

AUDIO:

500 mVrms (100% modulation)
Impedance: 47 kilohms

YP

B

P

R

 (Component Video):

Y: 1.0 Vp-p, 75 ohms unbalanced, sync 

negative

P

B

:0.7 Vp-p, 75 ohms

P

R

:0.7 Vp-p, 75 ohms

Signal format: 480i, 480p, 720p, 1080i

AUDIO: 

500 mVrms (100% modulation)

500 mVrms (100% modulation)

500 mVrms (100% modulation)

Impedance: 47 kilohms

Impedance: 47 kilohms

HDMI:

Video:480i, 480p, 720p, 1080i
Audio:Two channel linear PCM 32, 44.1 

and 48 kHz, 16, 20 and 24 bits

AUDIO:

More than 1 Vrms at the maximum volume setting (Variable)
More than 500 mVrms (Fixed)

D-sub 15-pin, analog RGB, 0.7 Vp-p, 75 ohms, positive

Stereo mini jack, 0.5 Vrms, 1 kilohm

Stereo mini jack
Impedance:

16 ohms

KLV-S19A10/S23A10 (UC)     2

Full range: 

4

 × 10 

cm (15 

7

/

8

 

× 

39 

3

/

8

 inches) (2)

5 W + 5 W

KLV-S23A10: 120-240 V AC, 50/60 Hz
KLV-S19A10: 18 V DC, with AC power adaptor

Model name:

AC-FD008

Rating: 

Input AC 100 V-240 V

50/60 Hz, 128 W

Output DC 18 V 6.11 A

In use:

KLV-S19A10: 95 W

KLV-S19A10: Less than 1.3 W
KLV-S23A10: Less than 1 W

KLV-S23A10: 110 W

In standby:

Dimensions (W/H/D):
KLV-S19A10: (with stand) 468 

×

 402

×

 218 mm

(18 

1

/

2

×

 15 

7

/

8

×

 8 

5

/

8

 inches)

(18 

1

/

2

×

 14 

3

/

8

×

 3 

3

/

8

 inches)

(without stand) 468 

×

 364 

×

 84 mm

KLV-S23A10: (with stand) 566 

×

 448

×

 218 mm

(22 

3

/

8

×

 17 

3

/

4

×

 8 

5

/

8

 inches)

(22 

3

/

8

×

 16 

1

/

4

×

 3 

5

/

8

 inches)

(without stand) 566 

×

 411 

×

 89 mm

KLV-S19A10: (with stand) 9.9 kg (21 lb. 14 oz.)

(without stand) 6.3 kg (13 lb. 15 oz.)

KLV-S23A10: (with stand) 12.3 kg (27 lb. 2 oz.)

(without stand) 8.7 kg (19 lb. 3 oz.)

Remote control RM-YA001 (1) 
Size AA batteries (2)
75-ohm coaxial cable (1) 
AC power cord (1) 
AC power adaptor (1) (KLV-S19A10 only) 
HD15-HD15 cable (1)
Support belt (1), securing screw (1) and wood screw (1)
Operating Instructions (1)
Quick Setup Guide (1)
Leaflet (Installing the Wall-Mount Bracket to the TV) (1)
Warranty Card (1)

Headphones plug adaptor
Connecting cables
Wall-Mount Bracket SU-WL11 (KLV-S19A10)

SU-LW1 (KLV-S23A10)

Design and specifications are subject to change 
without notice.

KLV-S19A10/S23A10 (UC)     3

KLV-S19A10/S23A10 (UC)     4

After correcting the original service problem, perform the
following safety checks before releasing the set to the customer:
1. Check the area of your repair for unsoldered or poorly-sol-

dered connections. Check the entire board surface for solder
splashes and bridges.

2. Check the interboard wiring to ensure that no wires are

“pinched” or contact high-wattage resistors.

3. Check that all control knobs, shields, covers, ground straps,

and mounting hardware have been replaced. Be absolutely cer-
tain that you have replaced all the insulators.

4. Look for unauthorized replacement parts, particularly transis-

tors, that were installed during a previous repair. Point them
out to the customer and recommend their replacement.

5. Look for parts which, though functioning, show obvious signs

of deterioration. Point them out to the customer and recom-
mend their replacement.

6. Check the line cords for cracks and abrasion. Recommend the

replacement of any such line cord to the customer.

7. Check the antenna terminals, metal trim, “metallized” knobs,

screws, and all other exposed metal parts for AC Leakage.
Check leakage as described right.

The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microamperes).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA

WT-540A. Follow the manufacturers’ instructions to use these
instruments.

2. A battery-operated AC milliammeter. The Data Precision 245

digital multimeter is suitable for this job.

3. Measuring the voltage drop across a resistor by means of a

VOM or battery-operated AC voltmeter. The “limit” indica-
tion is 0.75 V, so analog meters must have an accurate low-
voltage scale. The Simpson 250 and Sanwa SH-63Trd are ex-
amples of a passive VOMs that are suitable. Nearly all battery
operated digital multimeters that have a 2 V AC range are suit-
able.  (See Fig. A)

Fig. A. Using an AC voltmeter to check AC leakage.

Ω

µ

!