DOWNLOAD Sony KLV-46W550A Service Manual ↓ Size: 4.85 MB | Pages: 45 in PDF or view online for FREE

– 4 –

1-5. Lead Free Information
The circuit boards used in these models have been processed
using Lead Free Solder. The boards are identified by the LF
logo located close to the board designation.

The servicing of these boards requires special precautions. It
is strongly recommended to use Lead Free Solder material in
order to guarantee optimal quality of new solder joints. Lead
Free Solder is available under the following part numbers:-

Due to high melting point of Lead Free Solder, the soldering
iron tip temperature needs to be set to 370 degrees
centigrade. This requires soldering equipment capable of
accurate temperature control coupled with a good heat
recovery characteristics.

For more information on the use of Lead Free Solder,
please refer to 

9

1

-

5

0

0

-

0

4

6

-

mm

m

m

m

m

m

m

m

3

.

0

Kg

5

2

.

0

0

2

-

5

0

0

-

0

4

6

-

7

m

4

.

0

Kg

0

5

.

0

1

2

-

5

0

0

-

0

4

6

-

7

m

5

.

0

Kg

0

5

.

0

2

2

-

5

0

0

-

0

4

6

-

7

m

6

.

0

Kg

5

2

.

0

3

2

-

5

0

0

-

0

4

6

-

7

m

8

.

0

Kg

0

0

.

1

4

2

-

5

0

0

-

0

4

6

-

7

m

0

.

1

Kg

0

0

.

1

5

2

-

5

0

0

-

0

4

6

-

7

m

2

.

1

Kg

0

0

.

1

6

2

-

5

0

0

-

0

4

6

-

7

m

6

.

1

Kg

0

0

.

1

7

  Figure 2:  LF logo

  Figure 3:  LF logo on circuit board

(1) Hold the center of a
     connector.

(2) Press the center of the 

 connector to insert it.

(3) Slide the slider to lock the
     connector. 

Lock

(1) Slide the slider to release      

the slider lock.

(2) Press the center lock tab
     to release the lock and pull
     the connector up. 

Unlock

– 5 –

PUSH

a. PHOTO SHOW THE POSITION
DURING REAR COVER OPENING
b. PUSH TOWARDS INNER SET
WHILE REMOVE REAR COVER
FROM SIDE CONTROL

Note:
Please refer to
Section 4 : Disassembly
for screws informations .

c. LIFT UP THE REAR
COVER FROM BOTTOM

PULL
UP

 

<TOP SIDE>

CLICK

<RIGHT SIDE>

Note:

1. Please refer to
  Section 4 : Disassembly
  for screws informations.

2. Please Make Sure Rear
  Cover Not Overlap with
  Bezel.

1

2

3

4

CLICKING POSITION (PUSH
FROM REAR COVER TO BEZEL)

1. FOR EASIER INSTALLATION AT TOP SIDE, CLICK
 

THE REAR COVER FROM SIDE TO CENTER

2. PUSH THE REAR COVER AT 4 POSITIONS
 

UNTIL CLICK SOUND COME OUT.

3. 3 POSITIONS AT TOP SIDE AND 1 POSITION AT
 

RIGHT SIDE (NEAR SIDE CONTROL)

PUSH POINT

– 6 –

Push and slant towards inner side of set.

Push this position to remove
Switch Unit more easily

– 7 –

2-4. LED Pattern
When safety shutdown occurs, Standby LED display reports the
cause by using the lightning patterns as indicated below.

Example:

The figure above shows LED display when
SHUTDOWN is caused by main power alert. It repeats
flashing for a specified number of times in 0.3sec/
cycle and has a 2 seconds interval of lighting off.
Please note that a 2 seconds interval of lighting off
is fixed regardless of abnormal state types.

2.0 sec

2.0 sec

0.3 sec

0.3 sec

 LED Typ e

       Description

Remark

Status

Display

Power LED

 

Remark

 POWER

  

Green: LED

    Green lights at power ON.

 STANDB

Picture Off/
Timer

Y

 

Red: One LED

 

Red lights during standby.

  Green/Amber
  : Two LEDs

   Green lights during Picture 
   OFF and amber lights 
   during Timer activation.

POWER ON

 

Green lights

OFF

in a normal state.

STANDBY

OF

OFF

F

Red lights

Red flashes

Microcomputer is

in a sleep state.

Failure

Classify the trouble
causes by the no.
of red blinking.

Standby LED

Microcomputer is

Light sensor
Remote control sensor

Picture Off/Timer

Standby

Power

Power

Volume

Home

Input select

PROG +/-/

/