Sony KLV-40ZX1 Service Manual ▷ View online
KLV-40ZX1 (CH) 1-7
Radiation sheet (BC)
Chassis sheet B
Chassis sheet A
Radiation
sheet (BC)
sheet (BC)
Chassis sheet C
1
Main chassis
2
Lower cabinet assy
1-2-13. MAIN CHASSIS AND LOWER CABINET RE-
MOVAL
Gasket
(TN)
(TN)
Gasket
(20x20)
(20x20)
Radiation sheet
(TUNER)
(TUNER)
2
Three screws
(+BVST 3X8)
1
Two screws
(+BVTP 3X8)
1
Two screws
(+BVTP 3X8)
2
Three screws
(+BVST 3X8)
3
BC board
1-2-12. BC BOARD REMOVAL
1)
Remove the four screws (+BVTP 3X8) and the six screws
(+BVST 3X8).
(+BVST 3X8).
2)
Remove the BC board from the main chassis.
Note: please note that when replacing the BC board, the
gasket (TN/20X20) and the radiation sheet (TUNER) is not
included in the BC board.
Note: please note that when replacing the BC board, the
gasket (TN/20X20) and the radiation sheet (TUNER) is not
included in the BC board.
KLV-40ZX1 (CH) 1-8E
1-3. STAND
1-3-1. BASE STAND REMOVAL
1-3-2. ARM STAND REMOVAL
5
One screw
(BVTP2 4X20)
2
One screw
(+PSW M4X12)
4
Arm stand assy
3
Four screws
(+PSW M5X12)
5
Two screws
(BVTP2 4X20)
8
Two screws
(+BVTP2 4X16)
6
Two screws
(+BVTP2 4X16)
1
Stand arm cover (U)
9
Stand case (U) assy
0
Speaker box assy
qa
Stand case (L)
7
Base stand assy
1
Two screws
(+BVTP 3X10)
6
One screw
(+BVTP 3X10)
3
Stand arm cover (L)
2
EH spring
5
HS cover
4
Stand protect
7
MJX connector
KLV-40ZX1 (CH) 2-1
SECTION 2
TROUBLESHOOTING
2-1. MONITOR (LDM-Z401A)
2-1-1. FLOW CHART
YES
NO
YES
START
Does the power led
stay on when the TV is
switched on ?
Is the picture and
sound OK ?
END
Do the buttons
on the TV & remote
commander work
properly?
Is the standby led
blink ?
See
2-1-3. Standby Led Blink
2-1-3. Standby Led Blink
See
2-1-2. No Power
2-1-2. No Power
See
2-1-4. No Picture
2-1-5. No Sound
2-1-4. No Picture
2-1-5. No Sound
See
2-1-6. TV/commander
button malfunction
2-1-6. TV/commander
button malfunction
NO
YES
NO
YES
NO
KLV-40ZX1 (CH) 2-2
OK
NG
GS1 Board
2 times Blinkings
B Board
Check REG12V at
pins 5/6 of CN6156
on the GS1 Board
OK
NG
GS1 Board
3 times Blinkings
B Board
Check REG12V at
pins 5/6 of CN6156
on the GS1 Board
2-1-2. NO POWER
2-1-3. STANDBY LED BLINK
1) 2 times Blinkings
2) 3 times Blinkings
OK
NG
GS1 Board
NO POWER
Check STBY 3.3V
at C6250 plus (+) terminal
on the GS1 Board
or
Check AC_OFF_DET voltage
at 2 pin of CN6157
on the GS1 Board
B Board
Click on the first or last page to see other KLV-40ZX1 service manuals if exist.