DOWNLOAD Sony KLV-40W300A / KLV-46W300A (serv.man2) Service Manual ↓ Size: 14.27 MB | Pages: 82 in PDF or view online for FREE

– 7 –

The units in this manual contain a self-diagnostic function. If an error occurs, the STANDBY LED will automatically begin to flash.
The number of times the LED flashes translates to a probable source of the problem.
A definition of the STANDBY LED flash indicators is listed in the instruction manual for the user’s knowledge and reference.
If an error symptom cannot be reproduced, the remote commander can be used to review the failure occurrence data stored in memory to
reveal past problems and how often these problems occur.

When an error occurs, the STANDBY LED will flash a set number of times to indicate the possible cause of the problem.
If there is more than one error, the LED will identify the first of the problem areas.
Result for all of the following diagnostic items are displayed on screen.
If the screen displays a “0”, no error has occurred .

Number of times STANDBY LED

Monitoring Items

Diagnostic Item Description

(Red) flashes

(Screen Display)

2 times

POW OVP

Main Power Over Voltage Protection

3 times

POW ERR1

Power Error

5 times

T_CON

T_CON Error

6 times

BACKLITE

Back Light Error (Panel Inverter)

7 times

TEMP ERR

Temperature Abnormal Detection

8 times

AUD PROT

Audio Abnormal Detection

9 times

FAN_ERR

FAN Error (Not Detected. Display Only)

10 times

DTT ERR

DTAU Power

13 times

BALANCER

Panel Balancer Error

Turn off the power switch on the TV main unit or unplug the power cord from the outlet to stop the STANDBY lamp from flashing.

2 times

4 times

5 times

LED ON  0.3 sec.

LED OFF 0.3 sec.

LED OFF

3 sec. 

[ FLASH COUNT ]

Note: One flash counts is not self-diagnostic.

STANDBY 
INDICATOR

– 8 –

For errors with symptoms such as “power sometimes shuts off” or “screen sometimes goes out” that cannot be confirmed, it is possible to
bring up past occurrences of failure for confirmation on the screen.

In standby mode, press buttons on the remote commander sequentially in rapid succession as shown below:

Since the diagnostic results displayed on the screen are not automatically cleared, always check the self-diagnostic screen
After you have completed the repairs, clear the result display to “0”.

To quit the entire self-diagnostic screen, turn off the power switch on the remote commander or the main unit.

5

* : Note that this differs from entering the service mode (volume +)

( Number button )

* 

( Volume )

( TV standby )

( Info )

SELF CHECK

002
003
005

006
007
008
009

010
013

POW OVP
POW ERR1
T_CON

BACKLITE
TEMP ERR
AUD PROT
FAN_ERR

DTT ERR
BALANCER

0000000000
0000000000
0000000000

0000000000
0000000000
0000000000
0000000000

0000000000
0000000000

0000000000
0000000000
0000000000

0000000000
0000000000
0000000000
0000000000

0000000000
0000000000

0000000000
0000000000
0000000000

0000000000
0000000000
0000000000
0000000000

0000000000
0000000000

00
00
00

00
00
00
00

00
00

Monitoring Items

For details, refer to "1-1. DIAGNOSTIC TEST INDICATORS"

[ SELF-DIAGNOSTIC SCREEN DISPLAY ]

Number of times STANDBY Indicator flashes

– 9 –

3

 Two screws

  (+BVTP 3X12)

4

 Rear cover assy (40)

1

 Three screws

  (+BVTP2 4X16)

1

 Three screws

 

(+BVTP2 4X16)

1

 Two screws

  (+BVTP2 4X16)

1

 Five screws

 

(+BVTP2 4X16)

1

 One screw

 

(+BVTP2 4X16)

2

 Two screws

 

(+PSW M5X12)

qa

 One screw

 

(+BVST 4X8)

qs

 Stand holder

2

 Stand (ML) assy

q;

 Stand holder

3

 One screw

 

(+BVST 3X8)

9

 One screw

 

(+BVST 4X8)

1

 Two screws

 

(+PSW M5X12)

4

 Two screws

  (+PSW M5X8)

7

 Two screws

 

(+PSW M5X8)

5

 ARM L assy

8

 ARM R assy

6

 One screw

 

(+BVST 3X8)

1

 Two screws

 

(+PSW M5X12)

– 10 –

2

 Multi button assy

1

 Connector assy

CN7001

3

 HW1 board

1

 Connector assy

5

 Side terminal bracket

6

 CARD bracket

4

 One screw

 

(+PSW M3X5)

4

 Two screws

 

(+PSW M3X5)

3

 HW2 board

CN7022

2

 Two screws

 

(+BVTP 3X12)