DOWNLOAD Sony KLV-40V410A / KLV-40W410A / KLV-46V410A / KLV-46W410A (serv.man2) Service Manual ↓ Size: 11.89 MB | Pages: 88 in PDF or view online for FREE

NTSC PAL-M/PAL-N

VHF: 2-13
UHF: 14-69
CATV: 1-125

75-ohm external terminal for RF inputs

LCD (Liquid Crystal Display) Panel

1,920 dots x 1,080 lines

KLV-40V410A/40W410A ~ 102 cm (40 inches)
KLV-46V410A/46W410A ~ 117 cm (46 inches)

Remote Commander RM-YD023
Two Size AA (R6) Batteries
AC Power Cord
Cable Holder (1 attached to the TV)
Operating Instructions
Quick Setup Guide
Warranty Card
Attaching the Table-Top Stand

Connecting Cables
Suport Belt Kit
DMX-DT1

220W

230W

260W

275W

All measurements are approximations.

300 x 300 mm

M6 x 12 - 18

Less than 0.1W

10W+10W

58 x 126 mm

986 x 684 x 279 mm

986 x 646 x 110 mm

1120 x 742 x 115 mm 

1120 x 782 x 307 mm

23 kg

20 kg

30 kg

26 kg

65 X 150 mm

These servicing instructions are for use by qualifi ed service personnel only. To reduce the risk of electric shock, do not perform any servicing other 
than that contained in the operating instructions unless you are qualifi ed to do so.

Be sure to follow these guidelines to protect your 
property and avoid causing serious injury.

• Before carrying the TV, disconnect all cables.
• Carrying the large size TV requires two or more 

people.

• When carrying the TV, place your hand as 

illustrated and hold it securely. Do not subject the 
TV to shocks, vibration, or excessive force.

• Lift the TV by placing your palm directly 

underneath the panel but do not:

• squeeze the speaker grill area
• place your fingers in the groove above the 

speaker grill area

• put stress on the LCD panel. 

• Do not lift the TV from the bottom center.

An isolation transformer should be used during any service to avoid possible shock hazard, because of live chassis. The chassis of this receiver is 
directly connected to the ac power line.

!

 SAFETY-RELATED COMPONENT WARNING!!

Components identifi ed by shading and ! mark on the schematic diagrams, exploded views, and in the parts list are critical for safe operation. Replace 
these components with Sony parts whose part numbers appear as shown in this manual or in supplements published by Sony. Circuit adjustments that 
are critical for safe operation are identifi ed in this manual. Follow these procedures whenever critical components are replaced or improper operation is 
suspected. 

There are critical components used in LCD color TVs that are important for safety. These components are identifi ed with shading and 

mark on the schematic diagrams and the electrical parts list. It is essential that these critical parts be replaced only with the part number 
specifi ed in the electrical parts list to prevent electric shock, fi re, or other hazard. 

NOTE: Do not modify the original design without obtaining written permission from the manufacturer or you will void the original parts and 
            labor guarantee. 

When installing the LCD panel on a wall, the LCD panel must be secured using the 4 mounting holes on the rear cover. 

 do not press on the panel or frame edge to avoid the risk of electric shock.

  do not scratch or press on the panel with any sharp objects.

  do not leave the module in high temperatures or in areas of high humidity for an extended period of time.

  do not expose the LCD panel to direct sunlight.

  avoid contact with water. It may cause a short circuit within the module. 

  disconnect the AC adapter when replacing the backlight (CCFL) or inverter circuit. 

(High voltage occurs at the inverter circuit at 650Vrms.) 

  always clean the LCD panel with a soft cloth material.

  use care when handling the wires or connectors of the inverter circuit. Damaging the wires may cause a short. 

  protect the panel from ESD to avoid damaging the electronic circuit (C-MOS). 

The circuit boards used in these models have been processed using
Lead Free Solder. The boards are identified by the LF logo located
close to the board designation e.g. H1 etc [ see example ]. The
servicing of these boards requires special precautions to be taken as
outlined below.

It is strongly recommended to use Lead Free Solder material in order to guarantee optimal quality of new solder joints. 
Lead Free Solder is available under the following part numbers :

Due to the higher melting point of Lead Free Solder the soldering iron tip temperature needs to be set to 370 degrees centigrade. 
This requires soldering equipment capable of accurate temperature control coupled with a good heat recovery characteristics.

For more information on the use of Lead Free Solder, please refer to  http://www.sony-training.com

9

1

-

5

0

0

-

0

4

6

-

7

m

m

3

.

0

g

K

5

2

.

0

0

2

-

5

0

0

-

0

4

6

-

7

m

m

4

.

0

g

K

0

5

.

0

1

2

-

5

0

0

-

0

4

6

-

7

m

m

5

.

0

g

K

0

5

.

0

2

2

-

5

0

0

-

0

4

6

-

7

m

m

6

.

0

g

K

5

2

.

0

3

2

-

5

0

0

-

0

4

6

-

7

m

m

8

.

0

g

K

0

0

.

1

4

2

-

5

0

0

-

0

4

6

-

7

m

m

0

.

1

g

K

0

0

.

1

5

2

-

5

0

0

-

0

4

6

-

7

m

m

2

.

1

g

K

0

0

.

1

6

2

-

5

0

0

-

0

4

6

-

7

m

m

6

.

1

g

K

0

0

.

1