DOWNLOAD Sony KLV-32S310A / KLV-37S310A Service Manual ↓ Size: 4.7 MB | Pages: 65 in PDF or view online for FREE

– 24 –

Make sure LVDS cable dress correct.

Sheet (Core)C

LVDS cable

Shield Tape

Connector Assy 13P

Connector Assy 6P

Clamp Edge(M)

Connector Assy 20P

Connector Assy 14P

Sheet (Core)C

Put LVDS cable straight

Tape(LCD)

Connector Assy 20P

IC4900 (DDR)

Need a gap

LVDS cable

IC4900 (DDR)

LVDS cable

Wire can not overlap this IC

1) Dress Connector Assy 14P, 13P, 6P & 20P with Clamp Edge(M).

 

2) Dress LVDS cable with Sheet(Core)C(2X) & Shield Tape and put under 

 

  Connector assy 6P, 14P & 13P.

 

3) Dress Connector Assy, 20P with Tape(LCD).

– 25 –

Middle of shield tape as
reference line

Tape(LCD)

Connector assy 20P
(H1 wire)

Speaker wire

Screw boss

Caution : Pull away from
screw boss

Tape(LCD)

1) Dress Connector Assy 20P(H1 wire) with Tape(LCD)(2X).

 

2) Dress speaker wire with clamp.

Dress SP Connector assy 4P  with slide clamp(1X) & LCD(Tape).

– 26 –

SP Connector Assy 4P

Caution : Pull away from
screw boss

Screw boss

Sheet(Core) C

Sheet(Core) C

Connector Assy 20P
(H4 wire)

Tape(LCD)

SP Connector Assy 4P

Tape(LCD)

Tape (LCD)

AC inlet wire

Connector Assy 20P

Connector Assy 1P

1) Dress Connector Assy 20P (H4 wire) & SP Connector Assy 4P with G5 bracket's hook(3X), 

 

  LCD tape(1X) and Slide clamp(1X).

 

2) Dress Connector assy 20P and SP Connector Assy 4P underneath AC filter inlet & ground wire.

 

3) Apply Sheet(Core)C(2X) on LCD panel.

 

4) Dress Connector Assy 20P (H4 wire) with Tape(LCD)(2X).

 

5) Dress Connector assy 20P and spk wire with LCD tape. (Make sure this is last step) 

1) Dress AC inlet wire with G5 bracket's hook.

 

2) Dress Connector Assy 20P with Side Jack bracket's hook.

 

3) Screw Connector Assy 1P to the direction.

– 27 –

1. Please protect caution items.

Parts that considered as caution or critical item when
servicing are shown by critical label or seal on cabinet,
chasis, parts etc.
Please make sure to protect these caution notes and
Intruction Manual.

2. Beware with electric shock

Live chassis can caused electric shock because its
connected to the ac power line. Therefore, please use
isolation transformer and gloves when changing parts or
remove plug. Please remember that there is high voltage
during servicing.

3. Use specification parts.

Some parts has its characteristic such as fire retardancy
and voltage value specification. Therefore, please use the
same specification to replace parts. Parts identified by
shading and critical mark on the schematic diagrams,
exploded views, and in the part list are critical for safe
operation. Replace these parts with Sony parts whose part
numbers appear as shown in this manual or in supplements
published by Sony. Circuit adjustments that are critical for
safe operation are identified in this manual. Follow these
procedures whenever critical parts are replaced or improper
operation is suspected.

1

  Press the middle

 

part of the connector

 

to insert till it locks.

2

  Press the right

 

side to confirm it is

 

locked.

3

  Press the left

 

side to confirm it is

 

locked.

The connector might not be properly locked when only pressed from the middle.
Be sure to press both sides to confirm it is property locked/

4. On a safety as before, attaching parts and leading wiring

by using insulated material such as tube and tape, there
are also parts that taken from printed wiring boards.
Therefore when doing the internal wiring by leading or using
clamper, make sure wires are kept away from sharp edges,
heat sink and high temperature or high pressure parts.

5. Safety after sevicing

For safety, please check whether removed screws, parts
and wires are same as before. And check there is no
deterioration of seviced parts. Please make an insulation
checking between plug and external metal parts.

6. Do not fix internal of power supply board/inverter.

For safety, please do not perform service at the power
supply board or inverter.