Sony KLV-20G400A Service Manual ▷ View online
9
KLV-20G400A
KLV-20G400A
SELF-DIAGNOSTIC FUNCTION
IMPORTANT:
The unit in this manual DOES NOT contain a self-diagnostic function. If an error occurs, the TV will not stay on. It is our recommendation that if a
repair is required for this set, the technician should bring both the A Board and the G Board to the customer location.
The unit in this manual DOES NOT contain a self-diagnostic function. If an error occurs, the TV will not stay on. It is our recommendation that if a
repair is required for this set, the technician should bring both the A Board and the G Board to the customer location.
Control Buttons
PIC OFF/TIMER
POWER
Description of LED Indictors
The unit in this manual DOES NOT contain a self-diagnostic function.
10
KLV-20G400A
KLV-20G400A
1-1. REAR COVER REMOVAL
SECTION 1: DISASSEMBLY
1 Remove 2 screws from top of Rear Cover, +BVTP 3X10
2 Remove 2 screws, +PSW M4X12
3 Remove 4 screws from Terminal area, +BVTP 3X10
4 Remove 2 screws, +PSW M4X12
5 Remove 2 screws, +PSW M4X12
6 Remove 8 screws from both sides of Rear Cover, -BVTP 4X12
2 Remove 2 screws, +PSW M4X12
3 Remove 4 screws from Terminal area, +BVTP 3X10
4 Remove 2 screws, +PSW M4X12
5 Remove 2 screws, +PSW M4X12
6 Remove 8 screws from both sides of Rear Cover, -BVTP 4X12
NOTE: The Vesa Brackets are not included in the Rear Cover Assembly. If you are replacing the
Rear Cover you must proceed to step 7.
Rear Cover you must proceed to step 7.
7 Remove 4 screws to detach the 2 Vesa Brackets from the Rear Cover. Save the screws and the brackets
and put them into the replacement Rear Cover.
1-2. FUNCTION
KEY
REMOVAL
1 Remove from Bezel
2 Release hooks
3 Disconnect one connector from the H1 Board.
2 Release hooks
3 Disconnect one connector from the H1 Board.
6
5
4
2
3
1
Rear Cover
Bezel
1
2
3
Key Cover
Function Key
H1 Board
Bezel
7
Rear Cover
Vesa Breacket
11
KLV-20G400A
KLV-20G400A
1-3. H3 BOARD REMOVAL
1-4. H2 BOARD, IR LENS, AND LED LENS REMOVAL
1 Remove 1 screw from the H3 Board.
2 Disconnect one connector
2 Remove 1 screw +PSW M3X6 and release the ground wire
2 Disconnect one connector
2 Remove 1 screw +PSW M3X6 and release the ground wire
1 Remove 3 screws, +BVTP 3X10 from H2 Board
2 Disconnect one connector
2 Disconnect one connector
2
1
H3 Board
Bezel
3
1
2
LED Lens
H2 Board
Bezel
IR Lens
12
KLV-20G400A
KLV-20G400A
1-5. A BOARD AND G BOARD REMOVAL
1 Remove 2 screws and release ground wire, +PSW M3X6
2 Remove 2 screws from bottom of Main Shield, +FH 3X4
3 Remove 4 screws, +PSW M3X6
4 Remove 1 screw (+FH 3X4) and a Hex Nut from Tuner
5 Remove 7 screws, +PSW M3X6
6 Disconnect 6 connectors
7 Remove 5 screws, +PSW M3X6
8 Disconnect 8 connectors
9 Release 1 PWB Holder
2 Remove 2 screws from bottom of Main Shield, +FH 3X4
3 Remove 4 screws, +PSW M3X6
4 Remove 1 screw (+FH 3X4) and a Hex Nut from Tuner
5 Remove 7 screws, +PSW M3X6
6 Disconnect 6 connectors
7 Remove 5 screws, +PSW M3X6
8 Disconnect 8 connectors
9 Release 1 PWB Holder
10 Slide out AC inlet with the G Board from the Main Bracket.
5
6
8
9
10
A Board
Main Bracket
B Board
Main Shield
7
4
2
1
3
Click on the first or last page to see other KLV-20G400A service manuals if exist.