Sony KF-42E200A / KF-50E200A / KF-55E200A (serv.man2) Service Manual ▷ View online
– 5 –
KF-42E200A/50E200A/55E200A
RM-GA007 RM-GA007 RM-GA007
Projection Lamp
Your TV uses a projection lamp as its light source. As
with any lamp, it has lifespan and needs to be replaced
when the message, “Projection lamp is nearing end of
life. Please replace the lamp.” appears on the screen,
the lamp indicator flashes, or the screen becomes
darker.
with any lamp, it has lifespan and needs to be replaced
when the message, “Projection lamp is nearing end of
life. Please replace the lamp.” appears on the screen,
the lamp indicator flashes, or the screen becomes
darker.
Notes
• After turning on your TV, it may take a while (1 minute or
less) before the picture appears.
• When the projection lamp wears out, the screen goes dark.
Replace the lamp with a new Sony XL-2400 replacement
lamp (not supplied). How to replace the lamp, see page 46.
lamp (not supplied). How to replace the lamp, see page 46.
• After lamp is replaced, please set the “Lamp
Replacement” option in the Setup Settings (page 37).
Warning
The light emitted from the lamp is quite bright when your TV
is in use. To avoid eye discomfort or injury, do not look into
the light housing when the power is on.
is in use. To avoid eye discomfort or injury, do not look into
the light housing when the power is on.
– 6 –
KF-42E200A/50E200A/55E200A
RM-GA007 RM-GA007 RM-GA007
Replacing the lamp
The projection lamp, which illuminates the picture,
has a limited life.
If the screen becomes dark, the color looks unusual,
“Projection lamp is nearing end of life. Please replace
the lamp.” appears on the screen, or the LAMP
indicator on the front of the LCD projection TV
flashes, it is time to replace the lamp with a new one
(not supplied).
This television uses a replaceable lamp as its light
source. Over time, the screen will gradually grow
darker as the lamp ages. Although rare, the lamp may
make a small pop and will no longer light up. The
lamp should be replaced after about 8,000 hours,
which is the standard amount of time it takes for the
lamp brightness to be reduced by half. Because the
actual lamp life will vary depending on the operating
conditions and environment, 8,000 hours is an
estimate, not a guarantee.
has a limited life.
If the screen becomes dark, the color looks unusual,
“Projection lamp is nearing end of life. Please replace
the lamp.” appears on the screen, or the LAMP
indicator on the front of the LCD projection TV
flashes, it is time to replace the lamp with a new one
(not supplied).
This television uses a replaceable lamp as its light
source. Over time, the screen will gradually grow
darker as the lamp ages. Although rare, the lamp may
make a small pop and will no longer light up. The
lamp should be replaced after about 8,000 hours,
which is the standard amount of time it takes for the
lamp brightness to be reduced by half. Because the
actual lamp life will vary depending on the operating
conditions and environment, 8,000 hours is an
estimate, not a guarantee.
WARNING
Electric appliances can cause fire or high temperature,
resulting in injury or death. Be sure to follow the instructions
below.
resulting in injury or death. Be sure to follow the instructions
below.
• Use a Sony XL-2400 replacement lamp (not supplied) for
replacement. Use of any other lamp may damage the LCD
projection TV.
projection TV.
• Do not remove the lamp for any purpose other than
replacement. Doing so may cause injury or fire.
• Do not put flammable materials and metal objects inside
the lamp receptacle of the TV after removing the lamp.
Doing so may cause fire or electrical shock. Do not touch
the lamp receptacle once the lamp has been removed.
Doing so may cause fire or electrical shock. Do not touch
the lamp receptacle once the lamp has been removed.
• When the lamp eventually burns out, you may hear a
noticeable pop sound. This is normal and it is inherent to
this type of lamp.
this type of lamp.
• In rare instances, the bulb may pop inside the lamp unit,
but the lamp unit is designed to contain all of the broken
glass pieces inside the lamp unit.
glass pieces inside the lamp unit.
CAUTION
1
Turn off the power on the main unit. Wait
several minutes, then unplug the power
cord.
(The cooling fan will continue to blow for
about two minutes after turning the power
off.)
several minutes, then unplug the power
cord.
(The cooling fan will continue to blow for
about two minutes after turning the power
off.)
2
Wait at least 30 minutes after unplugging
the power cord to allow the lamp to cool
down before replacing it. To avoid being
burned, do not touch the lamp receptable
once the lamp has been removed.
the power cord to allow the lamp to cool
down before replacing it. To avoid being
burned, do not touch the lamp receptable
once the lamp has been removed.
3
Take the new lamp out of the box.
Do not touch the glass portion of the new
lamp.
Do not touch the glass portion of the new
lamp.
Notes
• Do not shake the lamp. Vibration can damage the
lamp or shorten its life.
• Avoid touching the front glass of a new lamp or the
glass of the lamp receptacle. This may reduce picture
quality or lamp life.
quality or lamp life.
4
Remove the outside lamp cover.
5
Remove the lamp door.
Turn the knob counterclockwise to OPEN and pull
out the cover.
out the cover.
Disposing of the lamp
This product contains mercury. For disposal or
recycling information, please contact your local
authorities.
Handling of the lamp
This product contains mercury. For disposal or
recycling information, please contact your local
authorities.
Handling of the lamp
•
Do not leave the used lamp near flammable
materials or within the reach of children.
materials or within the reach of children.
•
Do not pour water onto the used lamp or put any
object inside the lamp. Doing so may cause the
lamp to burst.
object inside the lamp. Doing so may cause the
lamp to burst.
Lamp door
– 7 –
KF-42E200A/50E200A/55E200A
RM-GA007 RM-GA007 RM-GA007
6
Pull out the lamp.
Hook a finger through the loop of the lamp handle
and pull the handle upwards. Then pull the lamp
straight out.
and pull the handle upwards. Then pull the lamp
straight out.
Notes
• The lamp is very hot immediately after use. Never
touch the glass portion of the lamp or the surrounding
parts.
parts.
• After the used lamp has cooled, place it into the empty
box of the replacement lamp. Never put the used lamp
into a plastic bag.
into a plastic bag.
7
Put the new lamp into its place.
Mount the new lamp securely. Failure to do so
may cause a fire or the screen to go dark.
may cause a fire or the screen to go dark.
Note
If the lamp is not securely reattached, the self-diagnostic
function may be triggered and the 1 indicator flashes
three times (page 9).
function may be triggered and the 1 indicator flashes
three times (page 9).
8
Reattach the lamp door.
Turn the knob back to CLOSE and secure the
cover.
cover.
9
Put the outside lamp cover back in its
place.
place.
Notes
• Consult your Sony dealer for a Sony XL-2400
replacement lamp.
• Take great care when replacing the lamp or plugging
in/unplugging the connecting cords. Rough handling
may cause the TV to fall, damaging the TV, the TV
stand and the floor.
may cause the TV to fall, damaging the TV, the TV
stand and the floor.
10
Turn on the TV and set the Lamp
Replacement in the Setup menu
(page 37).
Replacement in the Setup menu
(page 37).
– 8 –
KF-42E200A/50E200A/55E200A
RM-GA007 RM-GA007 RM-GA007
CAUTION
These servicing instructions are for use by qualified service per-
sonnel only.
To reduce the risk of electric shock, do not perform any servicing
other than that contained in the operating instructions unless you
are qualified to do so.
sonnel only.
To reduce the risk of electric shock, do not perform any servicing
other than that contained in the operating instructions unless you
are qualified to do so.
WARNING!!
AN ISOLATION TRANSFORMER SHOULD BE USED DURING
ANY SERVICE TO AVOID POSSIBLE SHOCK HAZARD, BE-
CAUSE OF LIVE CHASSIS.
THE CHASSIS OF THIS RECElVER IS DIRECTLY CONNECTED
TO THE AC POWER LINE.
ANY SERVICE TO AVOID POSSIBLE SHOCK HAZARD, BE-
CAUSE OF LIVE CHASSIS.
THE CHASSIS OF THIS RECElVER IS DIRECTLY CONNECTED
TO THE AC POWER LINE.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY SHADING AND MARK
! ON THE
SCHEMATIC DIAGRAMS, EXPLODED VIEWS AND IN THE
PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE
THESE COMPONENTS WITH SONY PARTS WHOSE PART NUM-
BERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLE-
MENTS PUBLISHED BY SONY. CIRCUIT ADJUSTMENTS THAT
ARE CRITICAL TO SAFE OPERATION ARE IDENTIFIED IN THIS
MANUAL. FOLLOW THESE PROCEDURES WHENEVER CRITI-
CAL COMPONENTS ARE REPLACED OR IMPROPER OPERA-
TION IS SUSPECTED.
PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE
THESE COMPONENTS WITH SONY PARTS WHOSE PART NUM-
BERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLE-
MENTS PUBLISHED BY SONY. CIRCUIT ADJUSTMENTS THAT
ARE CRITICAL TO SAFE OPERATION ARE IDENTIFIED IN THIS
MANUAL. FOLLOW THESE PROCEDURES WHENEVER CRITI-
CAL COMPONENTS ARE REPLACED OR IMPROPER OPERA-
TION IS SUSPECTED.
Click on the first or last page to see other KF-42E200A / KF-50E200A / KF-55E200A (serv.man2) service manuals if exist.