Sony KDS-50A2020 / KDS-55A2020 / KDS-60A2020 Service Manual ▷ View online
– 12 –
KDS-50A2020/55A2020/60A2020
K
RM-YD010 RM-YD010 RM-YD010
3. Blinking count display of POWER/STANDBY indicator
- One blink is not used for self-diagnosis.
- Example
Diagnosis item
Diagnosis item
LED blinks
Lamp cover
3 times
Fan
4 times
LED ON : 0.3sec
LED OFF : 0.3sec
LED OFF : 0.3sec
- Release of POWER/STANDBY indicator blinking
The POWER/STANDBY indicator blinking display is released by removing the plug from
the power or leaving for 2 minutes.
the power or leaving for 2 minutes.
4. Self-diagnosis screen displays
- In cases of malfunctions where it is not possible to determine the symptom such as when
the power goes off occasionally or when the screen disappears occasionally, there is a
screen display on whether the malfunction occurred or not in the past (and whether the
detection circuit operated or not) in order to allow confirmation.
screen display on whether the malfunction occurred or not in the past (and whether the
detection circuit operated or not) in order to allow confirmation.
<Screen Display Method>
- Quickly press the remote command button in the following order from the standby state.
Channel
Vol
Be aware that this differs from the method of entering the
service mode (Vol +).
LED OFF
3.0sec
DISPLAY
5
-
POWER
002 : TEMP
001
003 : L_COVER
000
004 : FAN
003
005 : L_DRIVER
000
006 : POWER
000
007 : AUDIO
000
008 : P_OVP
000
009 : DEVICE
000
101 : DTT_WDT
000
102 : TVM_WDT
002
103 : WEM_WDT
000
104 : DEM_WDT
000
12345-67890
SELF CHECK
* The boot count is increased at all power on timing.
(AC Off ->Power On, Main SW Off -> Power On, Standby -> Power On)
* The total power on time is written to NVM at 1 time per a hour.
(AC Off ->Power On, Main SW Off -> Power On, Standby -> Power On)
* The total power on time is written to NVM at 1 time per a hour.
Error information
002
: LED blink times
TEMP : Panel Temp Error
001
001
: Error count (Max 255)
Reboot counter
102
: Error number
TVM_WDT : Reboot micro
002
002
: WDT count (Max 255)
Boot count and total power on time
Display rule
12345-67890 : alternately display
(ex.)
12345-67890 : alternately display
(ex.)
Boot Count
13579 times
Total power on time
24680 hours
Each max is 99999
POWER
POWER indicator
LAMP indicator
TIMER
LAMP
POWER
OPEN
POWER
TIMER
LAMP
POWER
– 13 –
KDS-50A2020/55A2020/60A2020
K
RM-YD010 RM-YD010 RM-YD010
- The results display is not automatically cleared. In case of repairs and after repairs, check
the self-diagnosis screen and be sure to return the results display to "0".
- If the results display is not returned to "0" it will not be possible to judge a new malfunction
after completing repairs.
<Method of Clearing Results Display>
1. Power off (Set to the standby mode)
2.
Channel
Vol
3. Channel
<Method of Ending Self-Diagnosis Screen>
- When ending the self-diagnosis screen completely, turn the power switch OFF on the
remote commander or the main unit.
5. Self-Diagnosis function operation
8
ENTER
DISPLAY
5
-
POWER
2
:
Temp over
When the inside temperature sensed with IC3150, IC3200 and IC2000
mounted on S1 board, S2 board and C board respectively exceed
the threshold, DEM (Display Engine u-com) detects it and makes
turn off the lamp.
mounted on S1 board, S2 board and C board respectively exceed
the threshold, DEM (Display Engine u-com) detects it and makes
turn off the lamp.
3
:
Lamp cover
When the lamp cover is opened or harness from T board is off, DEM detects it
and makes turn off the lamp
4
:
FAN error
When any FAN is stopping or harness is not connected correctly,
DEM detects it and makes turn off the lamp
DEM detects it and makes turn off the lamp
5
:
Lamp Driver
When the ballast is not working with high voltage, DEM detects it and makes
turn off the lamp
turn off the lamp
6
:
Power error
When the voltage converted on 5V regulated from 11V is low, TVM
(TV u-com) detects it and makes turn off the lamp.
(TV u-com) detects it and makes turn off the lamp.
7
:
Audio
When DC is appeared by audio amp failure at speaker line, DEM detects it
and makes turn off the lamp.
and makes turn off the lamp.
8
:
Power-OVP
When the output voltage from 7V is abnormally high, TVM detects
it and makes turn off the lamp.
it and makes turn off the lamp.
9
:
Device error
When the temperature sensor and bus decoder ICs do not return ACK on IIC
bus to DEM, DEM detects it and makes turn off the lamp.
LAMP
:
Lamp
When the lamp is broken, DEM detects it.
– 14 –
KDS-50A2020/55A2020/60A2020
K
RM-YD010 RM-YD010 RM-YD010
SECTION 2
DISASSEMBLY
2-1. REAR COVER
3
2
1
Pull the claw
Lamp door
7 screws (+BVTP2 4x16)
Rear cover
Note: Photographs in this section are KDS-50A2000/55A2000/60A2000. KDS-50A2020/55A2020/60A2020 are metallic black
models, the structure is quite same as KDS-50A2000/55A2000/60A2000 though the color is different.
– 15 –
KDS-50A2020/55A2020/60A2020
K
RM-YD010 RM-YD010 RM-YD010
2-2. CHASSIS BLOCK
2
Screw (+BVTP2 4x16)
1
Connectors
3
3
Click on the first or last page to see other KDS-50A2020 / KDS-55A2020 / KDS-60A2020 service manuals if exist.