DOWNLOAD Sony KDL-55W950B / KDL-55W955B / KDL-55W957B / KDL-65W950B / KDL-65W955B Service Manual ↓ Size: 3.45 MB | Pages: 49 in PDF or view online for FREE

Model
KDL-55W950B KDL-55W955B KDL-55W957B KDL-65W950B KDL-65W955B
Pages
49
Size
3.45 MB
Type
PDF
Document
Service Manual
Brand
Device
TV / COMMON
File
kdl-55w950b-kdl-55w955b-kdl-55w957b-kdl-65w950b-kd.pdf
Date

Sony KDL-55W950B / KDL-55W955B / KDL-55W957B / KDL-65W950B / KDL-65W955B Service Manual ▷ View online

RB2G
 CHASSIS 
W950B/ W955B/ W957B/ M25B 
3) Measuring the voltage drop across a resistor by means of a VOM or battery  
operated AC voltmeter. The 'limit' indication is 0.75V so analog meters must  
have an accurate low voltage scale. The SIMPSON'S 250 and SANWA SH-
63TRD are examples of passive VOMs that are suitable. Nearly all  battery 
operated digital multimeter that have a 2 VAC range are suitable.   
(see Figure 2.) 
 
 
 
 
 
 
 
1-4. Safety Check-Out 
After correcting the original service problem, perform the following 
safety checks before releasing the set to the customer:- 
1) Check the area of your repair for unsoldered or poorly soldered  
connections.  Check the entire board surface for solder splashes and bridges. 
2) Check the inter board wiring to ensure that no wires are pinched or  
contact  high-wattage resistors. 
3)Check  all  control  knobs,  shields,  covers,  ground  straps  and  mounting  
hardware  have  been  replaced.  Be  absolutely  certain  you  have  replaced  all  
the insulators. 
4) Look for unauthorized replacement parts, particularly transistors that  
were  installed  during  a  previous  repair.  Point  them  out  to  the  customer  and  
recommend their replacement. 
5)  Look  for  parts  which,  though  functioning  show  obvious  signs  of 
deterioration.  Point  them  out  to  the  customer  and  recommend  their 
replacement. 
6)  Check  the  line  cords  for  cracks  and  abrasion.  Recommend  the 
replacement  of any such line cord to the customer. 
7) Check the antenna terminals, metal trim, metalized knobs, screws  and all  
other exposed metal parts for AC leakage. Check leakage test as described  
next. 
8.  For  safety  reasons,  repairing  the  Power  board  and/or  Inverter  board  is 
prohibited. 
 
 
 
 
 
 
 
 
 
 
Figure 2. AC voltmeter to check AC leakage 
Safety Notes 
1-3. Caution About  the Lithium Battery 
1)  Danger of explosion if battery is incorrectly replaced.  Replace only with 
the same or equivalent type. 
 2) Outer case broken battery should not contact to water. 
1-5.Leakage Test 
The AC leakage from any exposed metal part to earth ground and from all 
exposed metal parts to any exposed metal part having a return to chassis must 
not exceed 0.5mA (500 microamperes). 
Leakage current can be measured by any one of the three methods:- 
1) A commercial leakage tester such as the SIMPSON 229 or RCA WT540A. 
Follow the manufacturers instructions to use those instructions. 
2) A battery-operated AC  milliampmeter The DATA PRECISION 245 digital  
multimeter is suitable for this job. 
1-6. How to Find a Good Earth Ground 
1) A cold-water pipe is a guaranteed earth ground; the cover-plate retaining 
screw on most AC outlet boxes is also at earth ground. 
2) If the retaining screw is to be used as your earth ground, verify that it is at 
ground by measuring the resistance between it and a cold-water pipe with an 
ohmmeter. The reading should be zero ohms. 
3) If a cold-water pipe is not accessible, connect a 60- to 100-watt trouble- 
light (not a neon lamp) between the hot side of the receptacle and the 
retaining screw. Try both slots, if necessary, to locate the hot side on the line; 
the lamp should light at normal brilliance if the screw is at ground potential 
(see Figure 3). 
 
 
 
 
 
 
 
 
 
Figure 3. Checking for earth 
ground. 
RB2G
 CHASSIS 
W950B/ W955B/ W957B/ M25B 
Safety Notes 
1-7. Lead Free Information 
The circuit boards used in these models have been processed using Lead 
Free Solder. The boards are identified by the LF logo located close to the 
board designation. 
 
 
 
 
 
 
 
Figure 4: LF Logo 
Figure 5: LF logo on circuit board 
The servicing of these boards requires special precautions. It is strongly 
recommended to use Lead Free Solder material in order to guarantee optimal 
quality of new solder joints.  
 
 
 
 
 
1-8. Handling the FLEXIBLE FLAT CABLE (FFC) 
 When you insert / pull out FFC, please grasp a reinforcement board and main 
body of FFC. 
Main  Board 
Main  Board 
Please hold reinforcement board and 
plunge it to depths. 
Please pull out FFC while pushing the 
button of both ends at the same time. 
< Insertion> 
Release Button 
of Connector 
FFC connector  broken  if pull out FFC 
without press and hold both Release 
Button of connector. Symptom 5X blinking 
will be appear due to improperly seated. 
<Pull out> 
RB2G
 CHASSIS 
W950B/ W955B/ W957B/ M25B 
频道  
频道  
主菜单 
SECTION 2 
SELF DIAGNOSTIC FUNCTION 
2-1. Overview of Control Buttons 
Self Diagnostic Function 
2-1-1. (EXCEPT CHINA) 
2-1-2. (CHINA) 
     INPUT SELECT /      
SELECT/ CONFIRM
 
Press to select the next  or 
previous channel. 
In TV Home Menu:  buttons 
will work  as  (select/confirm) 
        +/- (Channel) /    /      , 
       +/- (Volume) /   /     . 
Press to select the next  or 
previous channel. 
Press to adjust the volume. 
In TV Home Menu:     buttons 
will work as    ,   ,   ,   .      
频道 
          Power 
Turn the TV on or switch to standby  mode 
 
Press to display 
 the TV Home Menu. 
主菜单 
TV CONTROLS/ TERMINALS/  INDICATOR 
FRONT 
Sensors /illumination/Microphone 
(Remote control sensor/ 
Light sensor/Built  in Microphone) 
REAR OF TV 
HOME 
Press to display  
the TV Home Menu. 
          Power 
Turn the TV on or switch to standby  mode 
          INPUT SELECT /      
SELECT/ CONFIRM
 
Press to select the next  or 
previous channel. 
In TV Home Menu:  buttons 
will work  as  (select/confirm) 
TV CONTROLS/ TERMINALS/  INDICATOR 
FRONT 
Example 
Illumination lights up or blinks in different 
colours according to the status of the TV  
( details  refer to 2-2. LED Display Control) 
 
CH+/- (Channel) /    /      , 
       +/- (Volume) /   /     . 
Press to select the next  or 
previous channel. 
Press to adjust the volume. 
In TV Home Menu:  buttons 
will work as    ,   ,   ,   .      
REAR OF TV 
Built in Camera 
Sensors /illumination/Microphone 
(Remote control sensor/ 
Light sensor/Built  in Microphone) 
Example 
Illumination lights up or blinks in different 
colours according to the status of the TV  
( details  refer to 2-2. LED Display Control) 
 
Built in Camera 
RB2G
 CHASSIS 
W950B/ W955B/ W957B/ M25B 
Status 
White Center 
LED 
(applicable for 
HSC2 only) 
Side RGB LED 
Side Amber 
LED 
Remarks 
Power Off 
( by power saving  switch off  and *1) 
Off 
Off 
Off 
*1  power switch off  (by side 
key)  
Power On 
White 
Off 
Off 
  
STBY/i.LINK STBY/PC STBY 
( by remote control off only ) 
Off 
Off 
Off 
  
Skype Call Receive 
White 
White one shot 
Off 
  
Picture Off 
White looping 
White one shot 
Off 
  
Device Connection 
White 
Cyan one shot 
Off 
  
Power ON Animation 
White 
White one shot 
Off 
  
Sleep Timer/On 
Timer/Reminder/REC Timer/Photo 
Frame 
( Power On ) 
White 
Amber  
One shot -> Lit*2 
Off 
*2 One Shot is only user action. 
On Timer/Reminder/REC Timer 
( Deep  Standby ) 
Off 
Off 
Amber 
After 5 minutes, side amber 
LED On 
Failure 
Off 
Red  
Blinking 
Off 
The number of LED blinking 
indicates cause of failure 
( refer  to Led Error / Triage 
chart) 
Aging mode 
White 
Green Blinking 
Off 
Blinking:0.5sec On / 0.5sec Off 
End of Aging mode 
White 
Green Blinking 
Off 
Blinking:3sec On / 3sec Off 
Software Updating 
white blinking 
white blinking 
off 
  
Software Updating finish 
White 
Blue lit 
off 
  
Test Reset  
White 
white blinking 
Amber 
blinking 
  
Error of panel ID 
White 
Green Blinking 
Amber 
Blinking 
Blinking:0.5sec On / 0.5sec Off 
REC (SCART REC & HDD 
REC/LIVE PAUSE) [AEP/J only] 
White 
Red(Pink)  
One shot -> Lit*2 
Off 
*2 One Shot is only user action. 
ePOP/ 
Shop Illumination 
White 
Cyan loop 
Off 
  
Self Diagnostic Function 
2-4. Standby LED Error Display 
2-2. LED Display Control 
When safety shutdown occurs, Standby LED display reports the cause by using the lightning 
patterns as indicated below
.  
3.0sec 
3.0sec 
0.5sec 
0.5sec 
Example: The figure above shows LED display when SHUTDOWN is caused by Audio   
 Error. It repeats flashing for a specified  number  of times in 0.5sec/cycle and has a 3 seconds 
 interval of lighting off. Please note that a 3 seconds interval of lighting off is fixed regardless of abnormal state types. 
2-3. LED Pattern 
Smart Core 
RED LED 
blinking count 
 
Detection Items 
 
Board Error Item 
2x 
Main 12V failure [MAIN_POWE] 
* This failure is not saved 
 G** Board Error 
 BAX Board  Error 
3x 
Main 5.0/3.3/1.8/1.0/ 1.1V failure [DC_ALERT] 
  * 5.0/1.0V failures are not saved. 
 BAX Board  Error 
Audio amp. protection [AUD_ERR] 
 BAX Board  Error 
 Speaker 
HDMI equalizer/switch I2C NACK [HDMI_EQ] * There is 
Temp. sensor on the same I2C bus. 
 BAX Board  Error 
Tuner or demodulator  I2C NACK [TU_DEMOD] 
 BAX Board Error 
AFE device  I2C NACK [AFE_I2C] 
 BAX Board  Error 
AFE device  error  SPI NACK [AFE_SPI] * only  for  AEP,CH 
 BAX  Board Error 
4x 
LED driver failure [LD_ERR] 
LED Driver (LD) Board Error 
Panel module  
LED voltage error [VLED]] 
LED Driver (LD) Board Error 
Panel module  
5x 
Panel ID EEPROM I2C NACK (Also panel power failure is 
a suspect) [P_ID_ERR] 
 Panel module  
 Tcon board 
G** Board Error 
 BAX Board  Error 
6x 
Backlight failure [BACKLIGHT] 
Panel module  
 G** Board Error 
 BAX Board  Error 
Backlight converter  OVP [BACKLIGHT] 
Panel module  
 Tcon board 
 G** Board Error 
 BAX Board  Error 
7x 
Over temperature protection [TEMP_ERR] 
Temp. sensor I2C NACK [TEMP_ERR] * There is HDMI Eq 
on the  same I2C bus. 
 BAX Board  Error 
8x 
Software Error (Also the main board’s memory or CAM 
module is a suspect) 
 BAX Board  Error 
9x 
Tuner Board Error [TU_BOARD] 
 Tuner Board Error 
Size 
G* Board  Type
 
 
55” 
G1A 
65” 
G2A 
Page of 49
Display

Click on the first or last page to see other KDL-55W950B / KDL-55W955B / KDL-55W957B / KDL-65W950B / KDL-65W955B service manuals if exist.