Sony KDL-52X2000 (serv.man2) Service Manual ▷ View online
- 5 -
FIX
RM-ED006
How to replace the fuse.
Open the fuse compartment with
a screwdriver blade and replace
the fuse.
Open the fuse compartment with
a screwdriver blade and replace
the fuse.
FUSE
WARNING (UK Models only)
The flexible mains lead is supplied connected to a B.S. 1363 fused
plug having a fuse of 13 AMP rating. Should the fuse need to be
replaced, use a 13AMP FUSE approved by ASTA to BS 1362, ie one
that carries the
plug having a fuse of 13 AMP rating. Should the fuse need to be
replaced, use a 13AMP FUSE approved by ASTA to BS 1362, ie one
that carries the
ASA
T
mark.
IF THE PLUG SUPPLIED WITH THIS APPLIANCE IS NOT SUIT-
ABLE FOR THE OUTLET SOCKETS IN YOUR HOME, IT SHOULD
BE CUT OFF AND AN APPROPRIATE PLUG FITTED. THE PLUG
SEVERED FROM THE MAINS LEAD MUST BE DESTROYED AS A
PLUG WITH BARED WIRES IS DANGEROUS IF ENGAGED IN A
LIVE SOCKET.
ABLE FOR THE OUTLET SOCKETS IN YOUR HOME, IT SHOULD
BE CUT OFF AND AN APPROPRIATE PLUG FITTED. THE PLUG
SEVERED FROM THE MAINS LEAD MUST BE DESTROYED AS A
PLUG WITH BARED WIRES IS DANGEROUS IF ENGAGED IN A
LIVE SOCKET.
When an alternative type of plug is used, it should be fitted with a
13 AMP FUSE, otherwise the circuit should be protected by a
13AMP FUSE at the distribution board.
13 AMP FUSE, otherwise the circuit should be protected by a
13AMP FUSE at the distribution board.
Model Name
Item
KDL-52X2000
(AEP)
KDL-52X2000
(UK)
PAP
OFF
OFF
PAT
OFF
OFF
RGB Priority
ON
ON
Sub Woofer
OFF
OFF
Scart 1
ON
ON
Scart 2
ON
ON
Scart 3
ON
ON
Front in (7)
ON
ON
Projector
OFF
OFF
Norm B/G
ON
OFF
Norm I
ON
ON
Norm D/K
ON
OFF
Norm AUS
OFF
OFF
Norm L
ON
OFF
Norm SAT
OFF
OFF
Norm M
OFF
OFF
Teletext
ON
ON
Nicam Stereo
ON
ON
- 6 -
FIX
RM-ED006
21 pin connector
19
17
15
13
11
9
7
5
3
1
20
18
16
14
12
10
8
6
4
2
21
Rear Connection Panel
Side Connection Panel
n
o
i
t
a
r
u
g
i
f
n
o
c
n
i
p
t
e
k
c
o
s
o
e
d
i
V
S
n
i
P
o
N
l
a
n
g
i
S
l
e
v
e
L
l
a
n
g
i
S
1
d
n
u
o
r
G
-
2
d
n
u
o
r
G
-
3
t
u
p
n
i
)
l
a
n
g
i
s
S
(
Y
,
m
h
o
5
7
B
d
3
-
/
+
V
1
V
3
.
0
.
c
n
y
S
e
v
i
t
i
s
o
p
B
d
0
1
+
3
-
4
t
u
p
n
i
)
l
a
n
g
i
s
S
(
C
B
d
3
-
/
+
V
3
.
0
e
v
i
t
i
s
o
p
,
m
h
o
5
7
.
c
n
y
S
S-Video
socket
Connected
Not Connected (open) * at 20Hz - 20kHz
Pin No
1
2
3
Signal
Signal level
1
Audio output B
(right)
(right)
Standard level : 0.5V rms
Output impedence : Less than 1kohm*
Output impedence : Less than 1kohm*
2
Audio input B
(right)
(right)
Standard level : 0.5V rms
Output impedence : More than 10kohm*
Output impedence : More than 10kohm*
3
Audio output A
(left)
(left)
Standard level : 0.5V rms
Output impedence : Less than 1kohm*
Output impedence : Less than 1kohm*
4
Ground (audio)
5
Ground (blue)
6
Audio input A
(left)
(left)
Standard level : 0.5V rms
Output impedence : More than 10kohm*
Output impedence : More than 10kohm*
7
Blue input
0.7 +/- 3dB, 75 ohms positive
8
Function select
(AV control)
(AV control)
High state (9.5-12V) : Part mode
Low state (0-2V) : TV mode
Input impedence : More than 10K ohms
Input capacitance : Less than 2nF
Low state (0-2V) : TV mode
Input impedence : More than 10K ohms
Input capacitance : Less than 2nF
9
Ground (green)
10
AVlink
11
Green
Green signal : 0.7 +/- 3dB, 75 ohms,
positive
positive
12
Open
13
Ground (red)
14
Ground (blanking)
15
_
_
Red input
0.7 +/- 3dB, 75 ohms, positive
_
(S signal Chroma
input)
input)
0.3 +/- 3dB, 75 ohms, positive
16
Blanking input
(Ys signal)
(Ys signal)
High state (1-3V) Low state (0-0.4V)
Input impedence : 75 ohms
Input impedence : 75 ohms
17
Ground (video
output)
output)
18
Ground (video
input)
input)
19
Video output
1V +/- 3dB, 75ohms, positive sync 0.3V
(-3+10dB)
(-3+10dB)
20
Video input
1V +/- 3dB, 75ohms, positive sync 0.3V
(-3+10dB)
Video input
Y (S signal)
1V +/- 3dB, 75ohms, positive sync 0.3V
(-3+10dB)
(-3+10dB)
21
Common ground
(plug, shield)
(plug, shield)
- - -
- - -
- 7 -
FIX
RM-ED006
FIX SELF DIAGNOSTIC SOFTWARE
The identification of errors within the FIX chassis is triggered in one of two ways :- 1: Busy or 2: Device failure to respond to IIC. In the event
of one of these situations arising the software will first try to release the bus if busy (Failure to do so will report with a continuous flashing
LED) and then communicate with each device in turn to establish if a device is faulty. If a device is found to be faulty the relevant device number
will be displayed through the LED (Series of flashes which must be counted).
of one of these situations arising the software will first try to release the bus if busy (Failure to do so will report with a continuous flashing
LED) and then communicate with each device in turn to establish if a device is faulty. If a device is found to be faulty the relevant device number
will be displayed through the LED (Series of flashes which must be counted).
Flash Timing Example : e.g. error number 3
StBy LED
ON
ON
OFF
OFF
LED Error Code
Number of LED Flashes
Error Message
02
Panel Temperature Error
03
+B_OVP Error
04
Fan Error
06
LowB Error
07
Audio Protector Error
09
Panel Error
11
Converter Error
Note :
•
For a more detailed explanation on fault finding please refer to Section 3-4, trouble shooting.
– 8 –
FIX
RM-ED006
The operating instructions mentioned here are partial abstracts
from the Operating Instruction Manual. The page numbers of
the Operating Instruction Manual remain as in the manual.
from the Operating Instruction Manual. The page numbers of
the Operating Instruction Manual remain as in the manual.
SECTION 1
GENERAL
2: Attaching the stand
(only for KDL-40X2000)
(only for KDL-40X2000)
1
Place the TV onto the stand by aligning the
screw hole alignment lines over the stand
as shown.
screw hole alignment lines over the stand
as shown.
2
Fix the TV to the stand using the supplied
screws.
screws.
Notes
• This TV is very heavy, so two or more people should place
the TV on the stand.
• If using an electric drill, set the tightening torque at
approximately 1.5 N·m (15 Kgf·cm).
3: Connecting an aerial/
VCR
VCR
1
2
2
Connecting an aerial only
Connecting an aerial and VCR
Coaxial cable
(supplied)
Mains lead (supplied)
Scart lead (not supplied)
VCR
Mains lead
(supplied)
(supplied)
Coaxial cable
(not supplied)
Coaxial cable
(supplied)
4: Preventing the TV
from toppling over
from toppling over
5: Bundling the cables
6: Selecting the
language and country/
region
language and country/
region
1
Connect the TV to your mains socket
(220-240 V AC, 50 Hz).
(220-240 V AC, 50 Hz).
2
Press
1
on the TV (right side).
When you switch on the TV for the first time, the
Language menu appears on the screen.
Language menu appears on the screen.
2
3
1
1
2
3,4
3,4
3,4
2
Click on the first or last page to see other KDL-52X2000 (serv.man2) service manuals if exist.