Sony KDL-40W3000 / KDL-46W3000 / KDL-52W3000 Service Manual ▷ View online
- 4 -
FIX2
RM-ED010
SPECIFICATIONS
ITEM MODEL
Television System
Stereo System
Channel Coverage
Color System
E
Analogue:
B/G/H, D/K, I, L
B/G/H, D/K, I, L
Digital:
DVB-T/DVB-C
DVB-T/DVB-C
GERMAN/NICAM
Stereo
Analogue: VHF : E2-E12
UHF : E21-E69
CATV : S1-S20
HYPER : S21-S41
D/K: R1-R12, R21-R69
L: F2-F10, B-Q, F21-F69
I: UHF B21-B69
Digital: VHF/UHF
UHF : E21-E69
CATV : S1-S20
HYPER : S21-S41
D/K: R1-R12, R21-R69
L: F2-F10, B-Q, F21-F69
I: UHF B21-B69
Digital: VHF/UHF
Analogue:
PAL, SECAM
NTSC 3.58/4.43
(VIDEO ONLY)
PAL, SECAM
NTSC 3.58/4.43
(VIDEO ONLY)
Digital:
MPEG-2 MP@ML,
MPEG-4 HP@L3/L4
MPEG-2 MP@ML,
MPEG-4 HP@L3/L4
U
Analogue:
I
I
Digital:
DVB-T/DVB-C
DVB-T/DVB-C
NICAM Stereo
Analogue: I: UHF B21-B69
Digital: VHF/UHF
Analogue:
PAL, SECAM
NTSC 3.58/4.43
(VIDEO ONLY)
PAL, SECAM
NTSC 3.58/4.43
(VIDEO ONLY)
Digital:
MPEG-2 MP@ML,
MPEG-4 HP@L3/L4
MPEG-2 MP@ML,
MPEG-4 HP@L3/L4
Projected Picture Size
LCD(Liquid Crystal Display) Panel
Approx 101.6cm (40 inches)
Approx 116.8cm (46 inches)
Approx 132.2cm (52 inches)
Approx 116.8cm (46 inches)
Approx 132.2cm (52 inches)
Sound Output
Right and Left speaker
Sub-woofer
2 x 11W (RMS)
Input/Output Terminals [REAR]
General Specifications
1: 21-pin Euro connector
(CENELEC standard)
Inputs for Audio and Video signals.
Inputs for RGB.
Inputs for RGB.
Outputs of TV Video and Audio
signals.
signals.
Power Requirements
220 - 240V
Power Consumption/
Standby
Standby
Approx 220W/0.3W (40 inches)
Approx 270W/0.3W (46 inches)
Approx 305W/0.3W (52 inches)
Approx 270W/0.3W (46 inches)
Approx 305W/0.3W (52 inches)
2: 21-pin Euro connector
(CENELEC standard)
(CENELEC standard)
Inputs for Audio and Video signals.
Inputs for RGB.
Inputs for RGB.
Outputs of Video and Audio signals
(Selectable). SmartLink interface.
(Selectable). SmartLink interface.
Dimensions
Approx 992x688x265mm
(40 inches with stand)
Approx 992x643x122mm
(40 inches without stand)
Approx 1135x779x306mm
(46 inches with stand)
Approx 1135x734x122mm
(46 inches without stand)
Approx 1278x874x384mm
(52 inches with stand)
Approx 1278x832x123mm
(52 inches without stand)
(40 inches with stand)
Approx 992x643x122mm
(40 inches without stand)
Approx 1135x779x306mm
(46 inches with stand)
Approx 1135x734x122mm
(46 inches without stand)
Approx 1278x874x384mm
(52 inches with stand)
Approx 1278x832x123mm
(52 inches without stand)
Weight
Approx 25.5kg (40 inches with stand)
Approx 22.0kg (40 inches without stand)
Approx 32.5kg (46 inches with stand)
Approx 28.5kg (46 inches without stand)
Approx 43.5kg (52 inches with stand)
Approx 36.0kg (52 inches without stand)
Approx 22.0kg (40 inches without stand)
Approx 32.5kg (46 inches with stand)
Approx 28.5kg (46 inches without stand)
Approx 43.5kg (52 inches with stand)
Approx 36.0kg (52 inches without stand)
Phono Jacks
Output Connectors variable for
Audio Signals.
Audio Signals.
Supplied Accessories
RM-ED010 Remote Commander (1)
IEC designated R06 battery (2)
Mains lead (Type BF) (1)
IEC designated R06 battery (2)
Mains lead (Type BF) (1)
Coaxial cable (1)
PC cable (1)
Support belt (1) and screws (2)
Stand (1) and screws (4) (40 and 46 inches only)
Support belt (1) and screws (2)
Stand (1) and screws (4) (40 and 46 inches only)
HDMI Inputs
HDMI Connectors
Other Features
High Picture Quality, High Sound Quality: S-
FORCE Front Surround. Live colour creation,
Bravia Engine EX, HDMI input, PC input, input.
FORCE Front Surround. Live colour creation,
Bravia Engine EX, HDMI input, PC input, input.
PC Input
15 Pin D Sub Connector
CAM
Conditional Access Module
Digital Output
Digital Output jack
Input/Output Terminals [SIDE]
Remote control system : Infrared control
Headphone jack
Stereo mini jack
Power requirements
3V dc
2 batteries IEC designation
2 batteries IEC designation
R06 (size AA)
Audio input
Phono jacks
Video input
Phono jack
S Video input
4 pin mini DIN
HDMI Input
HDMI Connector
Design and specifications are subject to change without notice.
- 5 -
FIX2
RM-ED010
CONNECTORS
21 Pin Connector (SCART)
_
_
Red input
0.7 +/- 3dB, 75 ohms, positive
_
(S signal Chroma
Connected
Not Connected (open) * at 20Hz - 20kHz
Pin No
1
2
Signal
Signal level
1
Audio output B
(right)
(right)
Standard level : 0.5V rms
Output impedence : Less than 1kohm*
Output impedence : Less than 1kohm*
2
Audio input B
(right)
(right)
Standard level : 0.5V rms
Output impedence : More than 10kohm*
Output impedence : More than 10kohm*
3
Audio output A
(left)
(left)
Standard level : 0.5V rms
Output impedence : Less than 1kohm*
Output impedence : Less than 1kohm*
4
Ground (audio)
5
Ground (blue)
6
Audio input A
(left)
(left)
Standard level : 0.5V rms
Output impedence : More than 10kohm*
Output impedence : More than 10kohm*
7
Blue input
0.7 +/- 3dB, 75 ohms positive
8
Function select
(AV control)
(AV control)
High state (9.5-12V) : Part mode
Low state (0-2V) : TV mode
Input impedence : More than 10K ohms
Input capacitance : Less than 2nF
Low state (0-2V) : TV mode
Input impedence : More than 10K ohms
Input capacitance : Less than 2nF
9
Ground (green)
10
AVlink
11
Green
Green signal : 0.7 +/- 3dB, 75 ohms,
positive
positive
12
Open
13
Ground (red)
14
Ground (blanking)
15
input)
0.3 +/- 3dB, 75 ohms, positive
16
Blanking input
(Ys signal)
(Ys signal)
High state (1-3V) Low state (0-0.4V)
Input impedence : 75 ohms
Input impedence : 75 ohms
17
Ground (video
output)
output)
18
Ground (video
input)
input)
19
Video output
1V +/- 3dB, 75ohms, positive sync 0.3V
(-3+10dB)
(-3+10dB)
20
Video input
1V +/- 3dB, 75ohms, positive sync 0.3V
(-3+10dB)
Video input
Y (S signal)
1V +/- 3dB, 75ohms, positive sync 0.3V
(-3+10dB)
(-3+10dB)
21
Common ground
(plug, shield)
(plug, shield)
- -
- -
19
17
15
13
11
9
7
5
3
1
20
18
16
14
12
10
8
6
4
2
21
How to replace the fuse.
Open the fuse compartment with
a screwdriver blade and replace
the fuse.
Open the fuse compartment with
a screwdriver blade and replace
the fuse.
FUSE
UK PLUG WARNING
WARNING (UK Models only)
The flexible mains lead is supplied connected to a B.S. 1363 fused
plug having a fuse of the correct rating for the set. Should the fuse
need to be replaced, use a fuse of the same rating approved by ASTA
to BS 1362, ie one that carries the
plug having a fuse of the correct rating for the set. Should the fuse
need to be replaced, use a fuse of the same rating approved by ASTA
to BS 1362, ie one that carries the
ASA
T
mark.
IF THE PLUG SUPPLIED WITH THIS APPLIANCE IS NOT SUIT-
ABLE FOR THE OUTLET SOCKETS IN YOUR HOME, IT SHOULD
BE CUT OFF AND AN APPROPRIATE PLUG FITTED. THE PLUG
SEVERED FROM THE MAINS LEAD MUST BE DESTROYED AS A
PLUG WITH BARED WIRES IS DANGEROUS IF ENGAGED IN A
LIVE SOCKET.
ABLE FOR THE OUTLET SOCKETS IN YOUR HOME, IT SHOULD
BE CUT OFF AND AN APPROPRIATE PLUG FITTED. THE PLUG
SEVERED FROM THE MAINS LEAD MUST BE DESTROYED AS A
PLUG WITH BARED WIRES IS DANGEROUS IF ENGAGED IN A
LIVE SOCKET.
When an alternative type of plug is used, it should be fitted with the
correct rating fuse, otherwise the circuit should be protected by the
same rating fuse at the distribution board.
correct rating fuse, otherwise the circuit should be protected by the
same rating fuse at the distribution board.
- 6 -
FIX2
RM-ED010
HDMI Connector
Rear Connection Panel
Side Connection Panel
n
o
i
t
a
r
u
g
i
f
n
o
c
n
i
p
t
e
k
c
o
s
o
e
d
i
V
S
n
i
P
o
N
l
a
n
g
i
S
l
e
v
e
L
l
a
n
g
i
S
1
d
n
u
o
r
G
-
2
d
n
u
o
r
G
-
3
t
u
p
n
i
)
l
a
n
g
i
s
S
(
Y
,
m
h
o
5
7
B
d
3
-
/
+
V
1
V
3
.
0
.
c
n
y
S
e
v
i
t
i
s
o
p
B
d
0
1
+
3
-
4
t
u
p
n
i
)
l
a
n
g
i
s
S
(
C
B
d
3
-
/
+
V
3
.
0
e
v
i
t
i
s
o
p
,
m
h
o
5
7
.
c
n
y
S
S-Video
socket
15 Pin D Sub Connector (PC)
1
Pin No
Signal Assignment
Pin No
Signal Assignment
1
TMDS Data2+
11
TMDS Clock Shield
2
TMDS Data2 Shield
12
TMDS Clock-
3
TMDS Data2-
13
CEC
4
TMDS Data1+
14
Reserved (N.C. on device)
5
TMDS Data1 Shield
15
SCL
6
TMDS Data1-
16
SDA
7
TMDS Data0+
17
DDC/CEC Ground
8
TMDS Data0 Shield
18
+5V Power
9
TMDS Data0-
19
Hot Plug Detect
10
TMDS Clock+
Pin No
Signal Assignment
Pin No
Signal Assignment
1
Red Out
9
+5V DC
2
Green Out
10
Sync Return (Ground)
3
Blue Out
11
Monitor ID0 in Display
4
Unused
12
DCC Serial Data
5
Ground
13
Horizontal Sync
6
Red Return
14
Vertical Sync
7
Green Return (Ground)
15
DCC Serial Clock
8
Blue Return (Ground)
- 7 -
FIX2
RM-ED010
FIX2 SELF DIAGNOSTIC SOFTWARE
The identification of errors within the FIX2 chassis is triggered in one of two ways :- 1: Busy or 2: Device failure to respond to IIC. In the
event of one of these situations arising the software will first try to release the bus if busy (Failure to do so will report with a continuous
flashing LED) and then communicate with each device in turn to establish if a device is faulty. If a device is found to be faulty the relevant
device number will be displayed through the LED (Series of flashes which must be counted).
event of one of these situations arising the software will first try to release the bus if busy (Failure to do so will report with a continuous
flashing LED) and then communicate with each device in turn to establish if a device is faulty. If a device is found to be faulty the relevant
device number will be displayed through the LED (Series of flashes which must be counted).
LED Error Code
Number of LED Flashes
Display Error Message
Item Description
02
POW_OVP
Main Power Over Voltage Protection
03
POW_ERR1
Power Error
05
T_CON
T-CON Error
06
BACKLITE
Back Light Error (Panel Inverter)
07
TEMP ERR
Temperature Abnormal Detection
08
AUD PROT
Audio Abnormal Detection
09
FAN_ERR
Fan Error
13
BALANCER
Panel BALANCER Error
Flash Timing Example : e.g. error number 3
StBy LED
Note :
•
For a more detailed explanation on fault finding please refer to Section 3-8, trouble shooting.
FIX2 Working Hours checking
To check working hours of products it is necessary to enter
the following mode.
the following mode.
1. Place TV in Stand By mode (Enter following sequence)
2. The following menu will appear on screen
3. In bottom left corner you can see following digits (Block 1-
Block2-Block3)
Block 1 (5 digits) - Working Hours
Block 2 (5 digits) - Unused
Block 3 (5 digits) - Panel Hours
Block 2 (5 digits) - Unused
Block 3 (5 digits) - Panel Hours
Note: Panel hours will be less than working hours due to “active
stand by” mode, working hours still increments, but panel hours
stops.
stand by” mode, working hours still increments, but panel hours
stops.
Click on the first or last page to see other KDL-40W3000 / KDL-46W3000 / KDL-52W3000 service manuals if exist.