Sony KDL-40VL130 / KDL-52W3000 / KDL-52WL130 / KDL-52WL135 Service Manual ▷ View online
17
KDL-40VL130/52W3000/52WL130/52WL135
KDL-40VL130/52W3000/52WL130/52WL135
1-10. DF4 BOARD, DF5 BOARD, AND GF2 BOARD REMOVAL
1 Remove 5 screws, +PSW 3SG
2 Disconnect 3 connectors
3 Disconnect 4 connectors
4 Remove 4 screws, +PSW 3SG
5 Disconnect 7 connectors
6 Remove 4 screws, +PSW 3SG
1-11. STAY REMOVAL
1 Remove 2 screws, +PSW M5X8
2 Remove 2 screws, +BVTP2 4X16
3 Remove 4 screws, +PSW M5X8
4 Remove 4 screws, +BVTP2 4X16
5 Remove 4 screws, +BVTP 4X8
6 Remove 3 screws, +BVTP2 4X16
(All Except KDL-40VL130)
4
3
2
1
Upper Stay (Left)
Stand Holder
Stand Holder
Lower Stay (Left)
Upper Stay (Right)
Lower Stay (Right)
Under Cover
6
5
(ALL EXCEPT KDL-40VL130)
1
2
4
3
6
5
G/D Bracket
GF2 Board
DF4 Board
DF5 Bracket
DF5 Board
18
KDL-40VL130/52W3000/52WL130/52WL135
KDL-40VL130/52W3000/52WL130/52WL135
1-12. LCD PANEL REMOVAL
1 Remove 1 screws, +BVTP2 4X16
2 Remove 4 screws, +BVTP2 4X16
3 Pop off from Speaker Cover
1
2
3
LED Guide
LCD Panel
Bezel
Speaker Cover
19
KDL-40VL130/52W3000/52WL130/52WL135
KDL-40VL130/52W3000/52WL130/52WL135
1-13. (BALANCER BOARDS) ETC-INVERTER MT BOARD REMOVAL
CAUTION:
Be sure to identify the inverter cover screws before proceeding. DO NOT remove the screws securing the plastic strip holding the lamp
sockets.
sockets.
1 Remove screws securing the (Balancer) Inverter Cover.
2 Remove screws securing the inverter board
3 Disconnect the connectors from the (Balancer) Inverter board you are removing.
4 For 52” models only,
to remove the lower board, disconnect 1 connector.
to remove the upper board, disconnect 2 connectors.
to remove the upper board, disconnect 2 connectors.
INVERTER BOARD REMOVAL
WARNING
NEVER REMOVE THE
SCREWS SECURING THE
PLASTIC STRIP HOLDING
PLASTIC STRIP HOLDING
THE LAMP SOCKETS
DAMAGE TO THE
BACKLIGHT TUBES WILL
Only remove the screws securing the inverter
cover which may be metal or plastic. The
remaining plastic strip contains sockets for the
fluorescent backlights and should never be
loosened. The backlights will pop out of the
sockets and/or break the backlight requiring a
LCD panel replacement. The example shown
is a 32” model but applies to all models.
REMOVE
CONNECTOR AND
PULL BOARD TO
THE RIGHT
!
.
OCCUR!
BACKLIGHT
END VIEW
SOCKET
3
3
Plastic Strip
holding
Lamp Socket
holding
Lamp Socket
NOTE: For the 52” models, the connector that attaches the
Left Upper (Balancer) Inverter board to the DF5 board has a strip of white tape
at both ends of the connector. The connector that attaches the
Right Upper (Balancer) Inverter board to the DF4 board has a strip of red tape
at both ends of the connector.
Left Upper (Balancer) Inverter board to the DF5 board has a strip of white tape
at both ends of the connector. The connector that attaches the
Right Upper (Balancer) Inverter board to the DF4 board has a strip of red tape
at both ends of the connector.
DO NOT
REMOVE
BACKLIGHT
SCREWS
REMOVE
BACKLIGHT
SCREWS
(Balancer) Inverter Cover
1
Plastic Strip
holding
Lamp Socket
holding
Lamp Socket
2
4
20
KDL-40VL130/52W3000/52WL130/52WL135
KDL-40VL130/52W3000/52WL130/52WL135
2-1. REMOTE ADJUSTMENT BUTTONS AND
INDICATORS
NOTE: RM-YD014 is for KDL-40VL130 & KDL-52WL135 Only, and
RM-YD017 is for KDL-52W3000 & KDL-52WL130 Only. Since the
buttons on the remote contols are in the same area, RM-YD017 is used
below to indicate their location.
RM-YD017 is for KDL-52W3000 & KDL-52WL130 Only. Since the
buttons on the remote contols are in the same area, RM-YD017 is used
below to indicate their location.
TV POWER
Onscreen cursor
and select button
and select button
DISPLAY
RM-YD017
5
VOLUME+
JUMP
SECTION 2: SERVICE ADJUSTMENTS
2-2. ACCESSING SERVICE ADJUSTMENTS
To adjust various set features, use the Remote Commander to put the set
into service mode to display the service menus.
into service mode to display the service menus.
1. TV must be in standby mode. (Power off).
2. Press the following buttons on the Remote Commander within a
second of each other:
DISPLAY
Channel
5
Volume
+
TV POWER .
The fi rst service menu (TV) displays.
3. To display the service menu that contains the category you want to
adjust, press JUMP on the Remote Commander.
CHASSIS SERVICE
000 GR
000
000
GRMD
0
SUB SERVICE
000 VERS
000
MODEL
MODEL ID: XXXXXXXXXX
Press JUMP
BEM
SERVICE
BOOT: 0.
026W00AU
MAIN: 0. 050W00AU
DATA: 0. 049A00LUW
Press JUMP
Press JUMP
DIGITAL
001 OP
001 OP
000
000 VERS
<SUB>
<DIGITAL>
SMO.100W00AA
DM0. 159A00AA
SD0.010W00AA
DD0.000A00LU
SB1.000W00AA
<BE>
BM0.050W00AU
BM0.050W00AU
BD0.049A00LUW
BB0.029W00AU
BB0.029W00AU
M2.001C
Press JUMP
SERVICE
Click on the first or last page to see other KDL-40VL130 / KDL-52W3000 / KDL-52WL130 / KDL-52WL135 service manuals if exist.