DOWNLOAD Sony KDL-40S4000 / KDL-40S4010 Service Manual ↓ Size: 5.41 MB | Pages: 60 in PDF or view online for FREE

1.

The following menu appears on the screen when you enter the
‘Set-up’ menu (See Pic.4). Be sure to check all pages.

1.

The following menu appears on the screen when you enter the
‘Sound’ menu (See Pic.5).

1.

The following menu appears on the screen when you enter the
‘IF Adjust’ menu (See Pic.6).

1.

The following menu appears on the screen when you enter the
‘White balance’ menu (See Pic.7).

1.

The following menu appears on the screen when you enter the
‘Error Menu’ menu (See Pic.8). Be sure to check all pages.

TT mode is available by setting the TV and Remote Commander for operation in Service Mode [ As shown on Page 11 ]. The functions
described below are then available by selecting the two numbers. To release the ‘TT mode’ press 00. To release the TT menu press the
menu key.

'TT' mode off

Set volume to 35%

Set volume to 50%

Set volume to 65%

Set volume to 80%

Ageing mode on

Shipping Condition

WB level check

Factory mode toggle (on/off)

CBA mode toggle (ON/OFF)

ECS mode toggle (ON/OFF)

Set BCN channels preset

Disconnect/Connect EDID WRITE to/from I2C general
bus

HDMI log enable/disable

Enable digital test

Re-initialise NVM

Select Dual Sound A

Select Dual Sound B

Select Dual Sound Mono

Select Dual Sound Stereo

Set NVM as non-virgin

Set NVM as virgin

EG1LL-GAUDI NW 40

EG1LL-GAUDI NW 46

EG1LL-GAUDI NW 52

Watchdog toggle

EG1LL-GAUDI BM 40

EG1LL-GAUDI BM-L 40

EG1LL-40L4000

Visual I2C toggle (VCT micro slave mode)

EG1LL-GAUDI NW 40 - VE Panel

EG1LL-GAUDI NW 46 - VE Panel

EG1LL-GAUDI NW 52 - VE Panel

EG1LL-GAUDI BM 40 - VE Panel

EG1LL-GAUDI BM-L 40 - VE Panel

EG1LL-40L4000 - VE Panel

VESA/JEIDA panel selection

HDMI number of inputs (2 or 3)

Set centred balance

Set volume to max

Set volume to min

Set balance full left

Set balance full right

Digital BER display

Digital Service menu

Digital colour bar output from DENC

TS CI path through

Digital tuner power down (Only one power cycle,

default is no power down)

Switch between two digital SW banks

Local keys test

Digital shipping conditions (Clear tune database)

LED test

OAD enable/disable toggle

TS CI path through with Reed Solomon off

LNA Setting On/Off (toggle)

Digital debug output: Enable/Disable

Digital 656 output: Enable/Disable

Digital Auto Reset function: Enable/Disable

Note : There are 2 types of panel fitted to this product:

1. Non-VE Panel
2. VE Panel

Ensure correct ‘TT’ commands are used for panel and screen size as shown in the above table. Check settings as follows.

Press the MENU on the Remote Commander and use the arrow keys to select the following menu options

SETTINGS -> SET-UP -> PRODUCT INFORMATION.

The screen as shown in the example below will appear. Check that the correct model information is displayed. If incorrect repeat
above procedure.

}

See Technical Bulletin

TS

A u d i o   o u t

IC3400

R

DDR

MPEG_Decoder

Hs/Vs

Comp

AV_SW

IC7100

LVDS_51P

SIF

HM4

SW

SP

BALANCER

IC5505

Chroma_Dec

N.R

UFE

T_CON

INDICATOR/SIRCS

SCART2

CN3400

Micro

CN6402

C I _ B u f f e r s

S c a l e r

KDL-40S/U40xx

RF

CVBS

CN301

BE2

HDMI1

PC

PCMCIA

HP_Out

HDMI_Dec

SW

Audio_DVI

CN8000

PC_Audio

LCD P

ANEL

MAIN BOARD

HDMI2

Line_Out

CN6401

LVDS

2P

HP

Video_Side

Temp_Sensor

EQ

Amp.

7P

IC8200

For_Audio

RTC

MS_JIG

DDR

L

NAND

SCART1

DDR

3D_Comb

IC4701

TXT_Dec

HDMI3_S

Micro

CN5500

CN101

CTRL_KEY

UNIT

CN6150

CN6706

POWER

CN6154

CN6700

I P 5 ( 4 0 )

•

All capacitors are in µF unless otherwise noted.

•

pF : µµF 50WV or less are not indicated except for 
electrolytic types.

•

Indication of resistance, which does not have one for 
rating electrical power, is as follows.

Pitch : 5mm
Electrical power rating : 1/4W

•

Chip resistors are 1/10W

•

All resistors are in ohms.
k = 1000 ohms, M = 1000,000 ohms

•

: nonflammable resistor.

•

: fusible resistor.

•

: internal component.

•

: panel designation or adjustment for repair.

•

All variable and adjustable resistors have 
characteristic curve B, unless otherwise noted.

•

All voltages are in Volts.

•

Readings are taken with a 10Mohm digital mutimeter.

•

Readings are taken with a color bar input signal.

•

Voltage variations may be noted due to normal production
tolerences.

•

:  B  +  bus.

•

: B - bus.

•

: RF signal path.

•

: earth - ground.

•

: earth - chassis.

: METAL FILM

: SOLID

: NON FLAMMABLE CARBON

: NON FLAMMABLE FUSIBLE

: NON FLAMMABLE METAL OXIDE

: NON FLAMMABLE CEMENT

: NON FLAMMABLE WIREWOUND

: ADJUSTMENT RESISTOR

: MICRO INDUCTOR

: TANTALUM

: STYROL

: POLYPROPYLENE

: MYLAR

: METALIZED POLYESTER

: METALIZED POLYPROPYLENE

: BIPOLAR

: HIGH TEMPERATURE

: HIGH RIPPLE

Les composants identifiés par une trame et
par une marque      sont d'une importance
critique pour la sécurité. Ne les remplacer
que par des pièces de numéro spécifié.
specified.

The components identified by shading
and marked      are critical for safety.
Replace only with the part numbers 
specified in the parts list.

CVM Board

A Board

S1 Board

VM

C

H

D1

A

J

A2

N

D

A1

D2

C

A