Sony KDL-40L4000 Service Manual ▷ View online
- -
CAUTION
Due to changes in the caution note
for MDF-61 connector, the caution
note has been placed in Appendix-A
for MDF-61 connector, the caution
note has been placed in Appendix-A
- 5 -
SPECIFICATIONS
Television System
Channel Coverage
Colour/Video System
Analogue:
Depending on your country/region
B/G/H, D/K, L, I
Depending on your country/region
B/G/H, D/K, L, I
Digital:
Depending on model
DVB-T/DVB-C
Depending on model
DVB-T/DVB-C
Analogue: VHF : E2-E12
UHF : E21-E69
CATV : S1-S20
HYPER : S21-S41
D/K: R1-R12, R21-R69
L: F2-F10, B-Q, F21-F69
I: UHF B21-B69
Digital: VHF/UHF
UHF : E21-E69
CATV : S1-S20
HYPER : S21-S41
D/K: R1-R12, R21-R69
L: F2-F10, B-Q, F21-F69
I: UHF B21-B69
Digital: VHF/UHF
Analogue:
PAL, SECAM
NTSC 3.58/4.43
(VIDEO IN)
PAL, SECAM
NTSC 3.58/4.43
(VIDEO IN)
Digital:
MPEG-2 MP@ML/HL
MPEG-2 MP@ML/HL
Input/Output Terminals [REAR]
General Specifications
1: 21-pin Euro connector
(CENELEC standard)
Inputs for Audio and Video signals.
Inputs for RGB.
Inputs for RGB.
Outputs of TV Video and Audio
signals.
signals.
Power Requirements
220 - 240V
Power Consumption/
Standby
Approx 175W/0.19W (Home/Standard mode)
Approx 197W/0.19W (Shop/Vivid mode)
Approx 197W/0.19W (Shop/Vivid mode)
2: 21-pin Euro connector
(CENELEC standard)
(CENELEC standard)
Inputs for Audio and Video signals.
Inputs for RGB and S Video.
Inputs for RGB and S Video.
Outputs of Video and Audio signals
(Selectable). SmartLink interface.
(Selectable). SmartLink interface.
Dimensions
Approx 995x688x276mm (With stand)
Approx 995x651x111mm (Without stand)
Approx 995x651x111mm (Without stand)
Weight
Approx 21.5kg (With stand)
Approx 18.5kg (Without stand)
Approx 18.5kg (Without stand)
Component In
Supported formats: 1080p, 1080i,
720p, 576p, 576i, 480p, 480i
Y: 1 Vp-p, 75 ohms, 0.3 negative
sync
720p, 576p, 576i, 480p, 480i
Y: 1 Vp-p, 75 ohms, 0.3 negative
sync
PB/CB: 0.7 Vp-p, 75 ohms
PR/CR: 0.7 Vp-p, 75 ohms
PR/CR: 0.7 Vp-p, 75 ohms
Other Features
High Picture & Sound Quality, Bravia Sync,
Integrated digital tuner for DVB-T/C,
Full HD Resolution 1920x1080, BBE Viva,
Integrated digital tuner for DVB-T/C,
Full HD Resolution 1920x1080, BBE Viva,
2 HDMI inputs, PC input, Dynamic contrast,
Virtual dolby surround.
Virtual dolby surround.
HDMI Inputs
Video: 1080/24p, 1080p, 1080i,
720p, 576p, 576i, 480p, 480i
Audio: Two channel linear PCM
32, 44.1 and 48kHz,
16, 20 and 24 bits
Analogue audio: Minijack
720p, 576p, 576i, 480p, 480i
Audio: Two channel linear PCM
32, 44.1 and 48kHz,
16, 20 and 24 bits
Analogue audio: Minijack
(HDMI IN 2 only)
PC Input
Video:15 Pin D Sub Connector
Audio: Minijack
Audio: Minijack
Sound Output
Right and Left speaker
2 x 10W (RMS)
CAM
Conditional Access Module Slot
Input/Output Terminals [SIDE]
Remote control system : Infrared control
Headphone jack
Stereo mini jack
Power requirements
3V dc
2 batteries IEC designation
2 batteries IEC designation
R06 (size AA)
Audio input
Phono jacks
Video input
Phono jack
Design and specifications are subject to change without notice.
- 6 -
CONNECTORS
21 Pin Connector (SCART)
_
_
Red input
0.7 +/- 3dB, 75 ohms, positive
_
(S signal Chroma
Connected
Not Connected (open) * at 20Hz - 20kHz
Pin No
1
2
Signal
Signal level
1
Audio output B
(right)
(right)
Standard level : 0.5V rms
Output impedence : Less than 1kohm*
Output impedence : Less than 1kohm*
2
Audio input B
(right)
(right)
Standard level : 0.5V rms
Output impedence : More than 10kohm*
Output impedence : More than 10kohm*
3
Audio output A
(left)
(left)
Standard level : 0.5V rms
Output impedence : Less than 1kohm*
Output impedence : Less than 1kohm*
4
Ground (audio)
5
Ground (blue)
6
Audio input A
(left)
(left)
Standard level : 0.5V rms
Output impedence : More than 10kohm*
Output impedence : More than 10kohm*
7
Blue input
0.7 +/- 3dB, 75 ohms positive
8
Function select
(AV control)
(AV control)
High state (9.5-12V) : Part mode
Low state (0-2V) : TV mode
Input impedence : More than 10K ohms
Input capacitance : Less than 2nF
Low state (0-2V) : TV mode
Input impedence : More than 10K ohms
Input capacitance : Less than 2nF
9
Ground (green)
10
AVlink
11
Green
Green signal : 0.7 +/- 3dB, 75 ohms,
positive
positive
12
Open
13
Ground (red)
14
Ground (blanking)
15
input)
0.3 +/- 3dB, 75 ohms, positive
16
Blanking input
(Ys signal)
(Ys signal)
High state (1-3V) Low state (0-0.4V)
Input impedence : 75 ohms
Input impedence : 75 ohms
17
Ground (video
output)
output)
18
Ground (video
input)
input)
19
Video output
1V +/- 3dB, 75ohms, positive sync 0.3V
(-3+10dB)
(-3+10dB)
20
Video input
1V +/- 3dB, 75ohms, positive sync 0.3V
(-3+10dB)
(-3+10dB)
Video input
Y (S signal)
1V +/- 3dB, 75ohms, positive sync 0.3V
(-3+10dB)
(-3+10dB)
21
Common ground
(plug, shield)
(plug, shield)
- -
- -
19
17
15
13
11
9
7
5
3
1
20
18
16
14
12
10
8
6
4
2
21
HDMI Connector
15 Pin D Sub Connector (PC)
1
Pin No
Signal Assignment
Pin No
Signal Assignment
1
TMDS Data2+
11
TMDS Clock Shield
2
TMDS Data2 Shield
12
TMDS Clock-
3
TMDS Data2-
13
CEC
4
TMDS Data1+
14
Reserved (N.C. on device)
5
TMDS Data1 Shield
15
SCL
6
TMDS Data1-
16
SDA
7
TMDS Data0+
17
DDC/CEC Ground
8
TMDS Data0 Shield
18
+5V Power
9
TMDS Data0-
19
Hot Plug Detect
10
TMDS Clock+
Pin No
Signal Assignment
Pin No
Signal Assignment
1
Red Out
9
+5V DC
2
Green Out
10
Sync Return (Ground)
3
Blue Out
11
Monitor ID0 in Display
4
Unused
12
DCC Serial Data
5
Ground
13
Horizontal Sync
6
Red Return
14
Vertical Sync
7
Green Return (Ground)
15
DCC Serial Clock
8
Blue Return (Ground)
- 7 -
EG1L SELF DIAGNOSTIC SOFTWARE
The identification of errors within the EG1L chassis is triggered in one of two ways :- 1: Busy or 2: Device failure to respond to IIC. In the
event of one of these situations arising the software will first try to release the bus if busy (Failure to do so will report with a continuous
flashing LED) and then communicate with each device in turn to establish if a device is faulty. If a device is found to be faulty the relevant
device number will be displayed through the LED (Series of flashes which must be counted).
event of one of these situations arising the software will first try to release the bus if busy (Failure to do so will report with a continuous
flashing LED) and then communicate with each device in turn to establish if a device is faulty. If a device is found to be faulty the relevant
device number will be displayed through the LED (Series of flashes which must be counted).
LED Error Codes and Descriptions
Number of LED
Flashes
Error Description
Micro
Checked
Action
02
DC_DET (12V main voltage).
VERD
In normal mode.
Goes into standby and LED flashes.
06
Panel Det error.
VERD
In normal mode.
Goes into standby and LED flashes.
07
Internal temperature error.
VERD
In normal mode.
Goes into standby and LED flashes.
08
Audio error (SP protection).
VERD
In normal mode.
Goes into standby and LED flashes.
10
Digital error.
VCT
In normal mode.
Adds error to error menu.
11
NVM error.
VCT
In initialisation state.
Adds error to error menu.
12
I2C error VCT.
VCT
In normal mode.
Adds error to error menu.
13
Balancer error.
VERD
In normal mode.
Goes into standby and LED flashes.
14
HDMI error.
VCT
In initialisation state.
Adds error to error menu.
15
Tuner Error
VCT
In initialisation state.
Adds error to error menu.
16
I2C CH1 (VERD TAS).
VERD
Factory mode.
LED error.
17
I2C CH0 (VERD NVM/RTC).
VERD
Factory mode.
LED error.
18
Digital demod.
EMMA
In normal mode.
Adds error to error menu.
19
USB error
EMMA
In normal mode.
Adds error to error menu.
20
CI error
EMMA
In normal mode.
Adds error to error menu.
21
VCT error
VERD
In normal mode.
LED error.
22
MSP error.
VCT
In initialisation state.
Adds error to error menu.
Self Diagnostic Screen Display
To bring up the self diagnostic screen display
i+
5
+
(ON SCREEN (DIGIT 5) (VOLUME +) (TV)
DISPLAY)
DISPLAY)
In standby mode, press the following sequence of buttons in quick succession on the remote commander as shown below:
Note that this differs from entering the service mode (volume + )
(TV POWER)
(ON SCREEN
DISPLAY)
DISPLAY)
(DIGIT 5)
(VOLUME -)
I/
TV
The following menu appears as shown below:
Click on the first or last page to see other KDL-40L4000 service manuals if exist.