Sony KDL-40HX752 / KDL-46HX752 Service Manual ▷ View online
KDL-40HX752/46HX752 vi
CAUTIONS AND WARNINGS
SAFETY CHECK-OUT
After correcting the original service problem, perform the following safety
checks before releasing the set to the customer:
1. Check the area of your repair for unsoldered or poorly soldered
connections. Check the entire board surface for solder splashes
and bridges.
2. Check the interboard wiring to ensure that no wires are pinched” or
touching high-wattage resistors.
3. Check that all control knobs, shields, covers, ground straps, and
mounting hardware have been replaced. Be absolutely certain that
you have replaced all the insulators.
4. Look for unauthorized replacement parts, particularly transistors,
that were installed during a previous repair. Point them out to the
customer and recommend their replacement.
5. Look for parts which, though functioning, show obvious signs of
deterioration. Point them out to the customer and recommend their
replacement.
6. Check the line cords for cracks and abrasion. Recommend the
replacement of any such line cord to the customer.
7. Check the antenna terminals, metal trim, metallized” knobs, screws,
and all other exposed metal parts for AC leakage. Check leakage
as described in “Leakage Test”.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and from all
exposed metal parts to any exposed metal part having a return to chassis,
must not exceed 0.5 mA (500 microamperes). Leakage current can be
measured by any one of three methods.
1. A commercial leakage tester.
Follow the manufacturers’ instructions provided with the tester.
2. A battery-operated AC milliammeter.
3. Measuring the voltage drop across a resistor by means of a VOM
or battery-operated AC voltmeter. The limit” indication is 0.75 V, so
analog meters must have an accurate low voltage scale. Nearly all
battery-operated digital multimeters that have a 2 VAC range are
suitable. (see Figure A)
To Exposed Metal
Parts on Set
0.15 µF
Earth Ground
AC
Voltmeter
(0.75V)
Figure A. Use an AC voltmeter to check AC leakage.
HOW TO FIND A GOOD EARTH GROUND
The cover-plate retaining screw on most AC outlet boxes is at earth ground.
Verify the AC outlet box retaining screw ground by connecting a 60W to
100W incandescent (not a neon or fluorescent lamp) between the hot side of
the receptacle and the retaining screw. Try both slots, if necessary, to locate
the hot side on the line; the lamp should light at normal brilliance if the screw
is at ground potential. (see Figure B)
Figure B. Checking for earth ground.
Trouble Light
AC Outlet Box
KDL-40HX752/46HX752 1
FEATURES
The AZ3G chassis is one of several designs for the 2012 model line of Sony
Bravia® LCD televisions. This manual covers the following models:
KDL-40HX752
KDL-46HX752
The BRAVIA® HX75x series LED LCD HDTV with 3D have incomparable
picture quality and an ultra-thin design
●
Brilliant Full HD (1080p) picture quality with Dynamic Edge LED
backlight with Frame Dimming
●
X-Reality™ Engine that creates crisp detail in each scene
●
4x High Speed 3D Panel with Motionflow™ XR 480
●
Dynamic Edge LED backlight for amazing contrast & color
●
One-touch access to the Sony Entertainment Network™ and apps
1
●
3D in Full HD 1080p for phenomenal 3D picture quality
2
●
Stream HD entertainment wirelessly with built-in Wi-Fi®
1
●
Skype™ ready
1
●
PC and tablet content
3
on your TV w/ Intelligent Connect
●
Media Remote™ app to control your TV with a smartphone
4
●
Built-in Wi-Fi™ (802.11n) enables you to connect to the TV via
Wi-Fi® without using a router
3
1. Broadband speed of at least 2.5 Mbps recommended (10 Mbps for HD). Content subject
to change and may require fees. Skype requires CMU-BR100 camera sold sep. Subject to
Skype’s terms and conditions.
2. Requires 3D content, 3D player, HDMI® cable (at least 10.2 Gbps) and 3D active glasses
sold separately.
3. Streaming content, copy-protected content and certain formats are not supported.
4. Requires devices connected to the same wireless home network.
4. Requires devices connected to the same wireless home network.
SECTION 1 - FEATURES AND OVERVIEW
SPECIFICATIONS
Sistema
Sistema de TV
Análogo: NTSC 3.58 / PAL-M / PAL-N
Digital:
SBTVD
Cobertura de canales
VHF: 2-13, UHF: 14-69
CATV (Análogo): 1-135
Sistema del panel
Panel LCD (pantalla de cristal líquido)
Salida de bocinas
10 W + 10 W
Tomas de entrada/salida
CABLE/ANTENNA
(Cable/Antena)
Terminal externa de 75 ohms para entrada de señal de radiofrecuencia
VIDEO IN 1
(Entrada de video 1)
Entrada de video/audio (izquierda-derecha)
COMPONENT IN
VIDEO IN 2
(Entrada de video 2)
YP
B
P
R
(video componente): 1080p (50, 60 Hz), 1080i (50, 60 Hz),
720p (50, 60 Hz), 576p, 576i, 480p, 480i
Entrada de audio (izquierda-derecha)
Entrada de video (contacto común de componente)
HDMI IN 1/2/3/4
(Entrada HDMI 1/2/3/4)
Video (2D):1080p (30, 50, 60 Hz), 1080/24p, 1080i (50, 60 Hz),
720p (30, 50, 60 Hz), 720/24p, 576p, 576i, 480p, 480i,
Formatos de PC
Video (3D) :
Estructuración de imágenes
1080p (30 Hz), 1080/24p, 1080i (50, 60 Hz),
720p (30, 50, 60 Hz), 720/24p
Una a lado de otra 1080p (50, 60 Hz), 1080/24p, 1080i (50, 60 Hz),
720p (30, 50, 60 Hz)
Una arriba de otra
1080p (30, 50, 60 Hz), 1080/24p, 1080i (50, 60 Hz),
720p (50, 60 Hz)
Audio: PCM lineal de dos canales 32; 44,1 y 48 kHz, 16, 20 y 24 bits,
Dolby Digital
Entrada de audio analógico (minitoma estéreo) (sólo HDMI IN 2, común con
PC IN (entrada de PC)
ARC (sólo HDMI IN 1)
AUDIO OUT
(Salida de audio)/Auriculares
Minitoma estéreo
DIGITAL AUDIO OUT
(OPTICAL)
Toma óptica digital (PCM lineal de dos canales, Dolby Digital)
PC IN (Entrada de PC)
PC/HDMI 2 AUDIO IN
(Entrada de audio de PC/
HDMI 2)
RGB analógico (Conector D-sub de 15 pines)
Entrada de audio (minitoma estéreo) (común con HDMI IN 2)
LA N
C onector 10BASE-T/100BASE-TX (La velocidad de la conexión podría variar en
función del entorno de red. No se garantizan la tasa de comunicación ni la
calidad de comunicación 10BASE-T/100BASE-TX para este TV.)
USB/DLNA
Consulte el i-Manual para el formato compatible.
KDL-40HX752/46HX752 2
SECTION 1 - FEATURES AND OVERVIEW
* El tamaño, las dimensiones y el peso de la pantalla son valores aproximados.
• La disponibilidad de los accesorios opcionales dependerá de los países, regiones, modelo del TV
y de las existencias.
• El diseño y las especificaciones están sujetos a cambios sin previo aviso.
Nombre del modelo KDL-
46HX752
40HX752
Alimentación y otras especificaciones
Requisitos de alimentación
Requisitos de alimentación
110-240 V ca, 50/60 Hz
Consumo de
potencia
en uso
130W
116W
en espera
Menos de 0,3 W
Tamaño de pantalla*
(cm)
(medido diagonalmente) (pulgadas)
116, 8
46
101, 6
40
Resoluci ón del monitor
1920 puntos (horizontal) × 1080 líneas (vertical)
Dimensiones* con soporte (mm)
1076 × 687 × 252
943 × 613 × 232
sin soporte
(mm)
1076 × 650 × 60
943 × 576 × 59
patrón de orificios
de montaje mural
(mm)
300 × 300
tamaño de
tornillos de
montaje mural
(mm)
M6 (8-12 mm)
Peso *
con soporte (kg)
17,6
14,3
sin soporte (kg)
14,6
11,8
Accesorios suministrados
Consulte (Verificación de los accesorios)
Accesorios opcionales
Gafas 3D:TDG-BR750/TDG-BR250/TDG-BR200/TDG-BR100/TDG-BR50
Unidad de cámara y micrófono: CMU-BR100
Adaptador de LAN inalámbrica USB: UWA-BR100
Unidad de cámara y micrófono: CMU-BR100
Adaptador de LAN inalámbrica USB: UWA-BR100
Temperatura de funcionamiento
0 ºC – 40 ºC
CHECKING THE ACCESSORIES
Control remoto (1)*
1
Pilas de tamaño AAA (2)
Soporte de sobremesa (1)*
Soporte de sobremesa (1)*
2
Tornillos de fijación para el soporte de
sobremesa (M5 × 16) (3)
Tornillos de montaje para el soporte de
sobremesa (M5 x 16) (4)
Manual de instrucciones (este manual) y
otros documentos
sobremesa (M5 × 16) (3)
Tornillos de montaje para el soporte de
sobremesa (M5 x 16) (4)
Manual de instrucciones (este manual) y
otros documentos
*
1
Consulte el número del modelo impreso en el
control remoto .
*
2
Se requiere ensamblar la base de soporte de
sobremesa. Para ensamblar la base de soporte
de sobremesa consulte el folleto suministrado.
KDL-40HX752/46HX752 3
SECTION 1 - FEATURES AND OVERVIEW
CHASSIS OVERVIEW
The primary circuits in the AZ3G chassis consist of a Main Board (BAPS Board), Power Supply Board (GL6 Board), the IR Board (HL Board), the 3D IR Emitter
(HEM3 Board), the Switch Unit, and the LCD Panel Assembly which includes the TCON Board.
NOTE: For connector part number information, refer to
NOTE: For connector part number information, refer to
“Connectors” on page 22
. For Wire Dressing information, refer to
“Wire Dressing” on page 24
.
SWITCH
UNIT
HL
HEM3
TCON
GL6
BAPS
KDL-40HX752 ONLY
SWITCH
UNIT
HL
HEM3
TCON
GL6
BAPS
KDL-46HX752 ONLY
Click on the first or last page to see other KDL-40HX752 / KDL-46HX752 service manuals if exist.