Sony KDL-40HX720 / KDL-40HX723 / KDL-40HX725 / KDL-46HX720 / KDL-46HX723 / KDL-46HX725 Service Manual ▷ View online
KDL-40/46HX720,723,725(AEP/UK)
81
APPENDIX-1
PROCEDURE TO ASSEMBLE THE REAR COVER (37/40/46)
1. Put the Rear Cover from the top side.
2. Push and confirm the locks in the order as shown below.
3. Confirm all the locks are fitting..
1
1
1
1
1
1
2
3
9
8
7
4
5
6
1
1
1
1
1
1
2
4
7
6
3
5
1
1
1
1
1
1
2
3
6
5
4
<37 Inch>
<40 Inch>
<46 Inch>
KDL-40/46HX720,723,725(AEP/UK)
82
<32/37/40/46/55/60 inch>
2.Peeling off the double sided tape.
To peel off the double sided tape between the bezel assembly and the panel, push the bezel down and pull the
panel up. To prevent breaking the panel it is prohibited to push the panel from the front.
panel up. To prevent breaking the panel it is prohibited to push the panel from the front.
1.Take off “Bracket, Panel”
Take off “Bracket, Panel” by pushing bezel hook.
The positions are shown on the following pages.
The positions are shown on the following pages.
Pushing hook
Put off
(1)Take off the LED board to assist with tape peel off.
(2)Put hand between bezel and panel from side, pull
panel up and push down bezel as shown in the picture.
panel up and push down bezel as shown in the picture.
Should pull up
metal area,
should not cell area.
metal area,
should not cell area.
(3)Moving hands along peel off the tape, pull up and push down near the tape as you go along.
Moving hands
step by step
step by step
APPENDIX-2
1. PROCEDURE TO REMOVE THE LCD PANEL FROM THE BEZEL ASSY
Peel off the double sided tape between the bezel assembly and the LCD panel when exchanging the LCD panel, etc, follow the instructions below.
KDL-40/46HX720,723,725(AEP/UK)
83
Because the double sided tape’s strength weakens once peeled off, peel off all the tape from bezel assembly, and stick new ones on (P/N: See Common Parts List).
1.Peel off the double sided tape from the panel.
(Possibly remains on the bezel side)
2. EXCHANGING THE DOUBLE SIDED TAPE
2position
5x290mm t=0.4
5x290mm t=0.4
2position
5x350mm t=0.4
5x350mm t=0.4
32”
37”
2position
5x380mm t=0.4
5x380mm t=0.4
40”
46”
3position
5x290mm t=0.4
5x290mm t=0.4
<32/37/40/46 inch>
2.Stick double sided tape.
Peel off separate papers before panel puts on.
APPENDIX-2
KDL-40/46HX720,723,725(AEP/UK)
84
1.Putting the panel on to bezel
(1) Put from upper side adjusting position to L/R side.
(2) Down panel on to bottom caring about fitting bezel position
ribs and panel cutout area.
Pay attention to the double sided tape, put the panel on to bezel assembly as shown below.
3. PUTTING THE PANEL ON TO THE BEZEL
(1)Put on upper side
(2)Put down
Care about positioning rib (L&R)
<32/37/40/46/55/60 inch>
<22/24/26 inch>
Please lock Panel with hooks of Bezel.
2.Lock with hooks of Bezel / Putting on “Bracket, panel”
<32/37/40/46/55/60 inch>
<22/24/26 inch>
Put brackets and confirm fixed by hook.
APPENDIX-2