DOWNLOAD Sony KDL-37S5500 / KDL-40S5500 Service Manual ↓ Size: 4.53 MB | Pages: 58 in PDF or view online for FREE

To remove the ‘G4’ board disconnect all the connectors and
then remove the 4 screws circled and ease the board gently
away from the back of the TV set.

Screw Part number(s) and Description(s)

2-580-629-01  SCREW, +BVST 3X8

     Screws

     Screws

Screw Part number(s) and Description(s)

2-580-629-01  SCREW, +BVST 3X8

To remove the ‘IP1F’ board disconnect all the connectors and
then remove the 4 screws circled and ease the board gently
away from the back of the TV set.

Note: Refer to page 4 - Hirose MDF61 connector.

5

+

(ON SCREEN
 DISPLAY)

(DIGIT 5)

(VOLUME 

+

)

i+

I/

Service adjustments to this model can be performed using the
supplied Remote Commander RM-ED017.

3.

The following menu appears on the screen (See Pic.1).

4.

Move to the corresponding adjustment item using the
‘    ’ or ‘    ’ arrow buttons on the Remote Commander.

5.

Press the ‘      ’ arrow button to enter into the required menu
item.

6.

Adjust the data value using the ‘     ’ or ‘     ’ arrow buttons on
on the Remote Commander.

7.

To go back at any time press the ‘     ’ button on the Remote
Commander.

8.

9.

Press the Red button or ‘Menu’ button on the Remote
Commander to quit the Service Mode when all adjustments
have been completed.

1.

Turn on the power to the TV set.

2.

Press the following sequence of buttons on the Remote
Commander.

The following description shows the items that can be
viewed and/or adjusted using the Service Menu.

•

After carrying out the service adjustments, to prevent the
customer accessing the ‘Service Menu’ switch the TV set
OFF and then ON again.

The following menu appears on the screen when you enter
the ‘Service General Menu’ (See Pic.2). This menu allows
you to view the product information, set the TV into Aging
Mode and perform Software Upgrade to the TV set.

The following menu appears on the screen when you enter
the ‘Service Alignments Menu’ (See Pic.3). This menu
allows adjustment of the TV picture levels. These adjustments
are set during manufacture and should not normally require
further adjustment.

The following menu appears on the screen when you enter
the ‘OSD Service Menu’ (See Pic.4). This menu
allows viewing and adjustment of the AGC and viewing of the
Sound Status.

The following menu appears on the screen when you enter
the ‘Country Selection Menu’ (See Pic.5). Using this menu
the destination country of the TV can be set.

Selection of ‘Factory Reset’ (See Pic.6) allows the TV to be reset
to factory shipping condition. This will restore all settings to
those which were contained in the TV on first shipment.

The TT modes described below are available by selecting the two
relevant digits. You can exit the ‘TT Mode’ by entering 00, by
pressing the ‘Analog’ or the ‘Digital’ button, by switching  the TV set
into Stand-by mode, or by Powering the TV set off.

'TT' mode off

Set volume to 35%

Set volume to 50%

Set volume to 65%

Set volume to 80%

Ageing mode on

Shipping Condition

WB Levels Check

Factory toggle mode (ON/OFF)

CBA mode toggle (ON/OFF)

ECS mode toggle (ON/OFF)

Set BCN channels preset

Full HD HDMI EDID Write

WXGA HDMI EDID Write

Re-initialise NVM

Select Dual Sound "A"

Select Dual Sound "B"

Select Dual Sound "Mono"

Select Dual Sound "Stereo"

Set NVM as non-virgin

Set NVM as virgin

Stop Main IIC Micro

WXGA /FHD Panel Selection

Set Centred Balance

Set Volume to Max

Set Volume to Min

Set Balance Full Left

Set Balance Full Right

Digital BER Display

TS CI Path Through

Front Panel Button Test

LED Test

TS CI Path Through With Reed Solomon Off

•

To place the Remote Commander in ‘TT Mode’ press the
following buttons together for approximately five seconds.

•

To use the Remote Commander in ‘TT Mode’ press the
‘Red’ text button on the Remote Commander twice.

TT will then appear in the bottom right hand corner of the TV.

i+

5

+

(ON SCREEN                            (DIGIT 5)                                (VOLUME +)                                  (TV)
   DISPLAY)

•

To take the Remote Commander out of ‘TT Mode’ press the
same buttons together for approximately five seconds.

TT Button