Sony KDL-32W605A / KDL-32W655A / KDL-42W655A Service Manual ▷ View online
KDL-32W605A/32W655A/42W655A 13
SECTION 3 - REPAIR INFORMATION
3. Slide brackets to detach from Main Board.
BRKT SIDE DC
BRKT SIDE TUNER
BRKT UNDER
4. Locate and remove screws, then lift the Main Board to detach.
5. Install the new Main Board and screws.
6. Reconnect the LVDS Cable and all other connectors.
7. Update the Software.
After ALL repairs UPDATE the SOFTWARE to the latest version.
Instructions are included with the Software package on the Sony
website.
Instructions are included with the Software package on the Sony
website.
a. Insert the USB device with the latest Software into one of the TVs’
USB ports.
b. Connect TV to AC power.
c. Wait at least 20 seconds.
d. Press
POWER
on the remote to turn ON the TV.
e. Wait until the Software update is complete.
5.
After removing screws, firmly grasp as shown to separate Chassis Box
from TV.
from TV.
6. Grasp and pull upwards on left and right side of Chassis Box to release
clips. Lift it upwards to detach.
REPLACING THE MAIN BOARD
The Main Board used in these models is available for repair. For Part
Number information refer to
Number information refer to
Section 4 - Exploded View/Part Number
Information on page 18.
1. Remove Harness and screws from the Main Board Bracket.
2. Turn Main Board Bracket and disconnect the remaining connectors.
KDL-32W605A/32W655A/42W655A 14
SECTION 3 - REPAIR INFORMATION
8. Access
Service Mode by pressing the following buttons within 1 second
of each other:
DISPLAY
Channel
5
Volume
+
POWER
9. When the
DIGITAL Menu appears, press
2
until
002 MODEL category
displays.
10. Press
1
until
001 DEST item displays.
DIGITAL
SERVICE
002 MODEL
001 DEST
SBTVD-T_BASE
CAUTION: If the incorrect Destination Data Value is selected, it may
corrupt the Sofware requiring a Main Board replacement.
corrupt the Sofware requiring a Main Board replacement.
11. Select the correct destination of the TV, press
3
to increase or
6
to decrease the data value (Use the table below for reference).
Model Name
Destination
Data Value
KDL-32W605A
BRAZIL
SBTVD-T_BASE
KDL-32W655A
BRAZIL
SBTVD-T_BASE
KDL-42W655A
BRAZIL
SBTVD-T_BASE
12. Press
MUTING
then
0
to save the changes.
DIGITAL
SERVICE
002 MODEL
001 DEST
001 DEST
WRITE
SBTVD-T_BASE
13. Press
3
until the model displayed matches the model of the TV.
CAUTION: The Model Name can only be selected once. Be sure
to verify the information is correct before saving the changes.
to verify the information is correct before saving the changes.
14. Press
MUTING
then
0
to save the changes.
DIGITAL
SERVICE
002 MODEL
002 MODELNAME
KDL-32W655A
WRITE
15. Locate the Serial Number for the TV on the side of the Rear Cover.
MODEL NO
KDL-32W655A
SERIAL NO
2000001
16. Press
1
until
003 SERIAL item displays.
DIGITAL
SERVICE
002 MODEL
003 SERIAL
17. Press
0
to display the
Serial Number Edit option.
DIGITAL (MODEL)
SERVICE
SerialNumberEdit
*1 SerialNumber
KDL-32W605A/32W655A/42W655A 15
SECTION 3 - REPAIR INFORMATION
18. Press
to display the
Serial Number input screen.
DIGITAL (MODEL)
SERVICE
SerialNumberEdit
*1 SerialNumber
Please Input serial number
(0000000-99999999)
_ _ _ _ _ _ _
CAUTION: The Serial Number can only be selected once. Be sure
to verify the information is correct before saving the changes.
to verify the information is correct before saving the changes.
19. Enter the Serial Number of the TV.
NOTE:
If the incorrect Serial Number is entered, press
RETURN
to go back to the Serial Number input screen and re-enter
the correct number.
the correct number.
20. Press
to save the Serial Number.
DIGITAL (MODEL)
SERVICE
SerialNumberEdit
*1 SerialNumber
2000001
WRITE
21. Clear the
Self Check screen.
a. Press
POWER
to exit
Service Mode.
b. Press the following buttons on the
Remote Commander within 1
second of each other:
DISPLAY
Channel
5
Volume
-
POWER
SELF CHECK
000 RESERVED
--------------------- --------------------- --------------------- 00
000 RESERVED
--------------------- --------------------- --------------------- 00
002 MAIN_POWE --------------------- --------------------- --------------------- 00
003 DC_ALERT
003 DC_ALERT
--------------------- --------------------- --------------------- 00
003 AUD_PROT
--------------------- --------------------- --------------------- 00
003 HDMI_EQ
--------------------- --------------------- --------------------- 00
003 TU_DEMOD --------------------- --------------------- --------------------- 00
004 VLED
004 VLED
--------------------- --------------------- --------------------- 00
004 LD_ERR
--------------------- --------------------- --------------------- 00
005 HFR_ERR
--------------------- --------------------- --------------------- 00
005 TCON_ERR
120123132522 120123113645 --------------------- 02
005 P_ID-ERR
--------------------- --------------------- --------------------- 00
006 BACKLITE
--------------------- --------------------- -------------------- 00
007 TEMP_ERR
--------------------- --------------------- --------------------- 00
007 FAN_ERR
--------------------- --------------------- --------------------- 00
010 EMITTER
--------------------- --------------------- --------------------- 00
101 VPC_WDT
--------------------- --------------------- --------------------- 00
102 MEPS_WDT --------------------- --------------------- --------------------- 00
103 HOST_WDT --------------------- --------------------- --------------------- 00
104 STBY_WDT
103 HOST_WDT --------------------- --------------------- --------------------- 00
104 STBY_WDT
--------------------- --------------------- --------------------- 00
00345 000333 06789
Error Count
c. To clear the error history and error count press
8
0
.
d. Press
POWER
to exit
Self Check Mode.
22. Cycle AC Power (Unplug and plug AC Cord from the outlet).
KDL-32W605A/32W655A/42W655A 16
SECTION 3 - REPAIR INFORMATION
REMOVING THE SPEAKERS
1. Press down the connector clip to disconnect.
NOTE:
For the Speaker Box Right you must also disconnect the Switch
Unit connector.
2. Remove screws and lift the Speaker Box to detach.
REPLACING THE SWITCH UNIT
1. Remove screws and press as shown to remove the Switch Unit.
2. Install the new Switch Unit, screws and connectors.
REMOVING THE SMART CORE BLOCK
1. Remove 1 screw, then release the Harness attached to LCD Panel.
2. Grasp Smart Core Block as shown, then twist it downwards to release
clips.
3. Apply pressure on both sides of Cover, SC and pull it apart to detach.
4. Disconnect connectors and release cable from Lid, SC hook.
5. Unclamp 2 side clips from the Lid, SC and lift as shown to detach.
LID, SC
Click on the first or last page to see other KDL-32W605A / KDL-32W655A / KDL-42W655A service manuals if exist.