Sony KDL-32R300C Service Manual ▷ View online
SELF CHECK
BACK
<<
00000-00012-00000
[Home] Exit
33
[To Bring Up Self Diagnostic(SELF CHECK)]
In standby mode, press buttons on
Or in power on , press buttons on
the remote commander sequentially in rapid succession as shown below:
In standby mode, press buttons on
Or in power on , press buttons on
the remote commander sequentially in rapid succession as shown below:
Total operation time by hour
Boot count
Panel operation time by hour
You can check the TV set operation time, boot count and panel operation time in service menu although this model doesn’t support self-diagnostics.
After you have completed the repairs, clear the result display to “0”.
Clearing the Self Check Diagnostic List
•
After you have completed the repairs, clear the result display to “0”.
Clearing the Self Check Diagnostic List
•
Panel operation time :
Press the Channel 7 and then press the Channel 0 to clean the Panel operation time.
Exiting the Self-diagnostic screen
To exit the Self Diagnostic screen, turn off the power to the TV by pressing the POWER button on the remote or the POWER button on the TV.
To exit the Self Diagnostic screen, turn off the power to the TV by pressing the POWER button on the remote or the POWER button on the TV.
[Operation Time, Boot Count, Panel Operation Time Screen]
APPENDIX-3 Operation Time, Boot Count, Panel Operation Time
KDL-32R300C U2
Service Mode
Wide Band Turning
Wide Band Turning
>>
Range Scan…
>>
Self diagnosis history >>
Status Information
Status Information
>>
LVDS Spectrum(%) <[ 32 ]>
STATUS DIGITAL RF INFORMATION >>
Low of HPD
STATUS DIGITAL RF INFORMATION >>
Low of HPD
<[ 5 ]>
Panel Selection <[ 20_TPT315B5-DX SFE1 ]>
TEST RESET <[ OFF ]>
UART Selection <[ Factory ]>
SERIAL NUMBER EDIT 3230016
TEST RESET <[ OFF ]>
UART Selection <[ Factory ]>
SERIAL NUMBER EDIT 3230016
MODEL NAME EDIT
KDL-32R300C
MHL TMDS Termination <[ 0 ]>
[</>Set[Home]Exit
[</>Set[Home]Exit
34
Edit: MODEL NAME
If the user select this menu, the below editing menu is appeared and adjusting it like "Program Labels" editing way.
XXX-XXXXXXX,
"X" part can change in below way by Remote Commander. Press up/down arrow key to scroll character ("A-Z","0-9","_") and press right arrow key to move the next position.
These number should be affected to "Product Information" in Setting Menu
* After user input data , press <Enter> will pop dialog to inform user to confirm data (Input data correct ?)
* Once data confirm and save into EEPROM , gray out this item , user will not able to adjust
Edit: Serial Number
When you select the SERIAL NUMBER EDIT item in the service mode, use right key to enter edit mode.
SERIAL NUMBER EDIT 0000001
Use the up and down key to edit the first bit of the SERIAL NUMBER (0~9)。
Use the left and right key to switch bit.
SERIAL NUMBER EDIT 0000001
SERIAL NUMBER EDIT 0000001
Use the up and down key to edit the first bit of the SERIAL NUMBER (0~9)。
Use the left and right key to switch bit.
SERIAL NUMBER EDIT 0000001
* After user input data , press <Enter> will pop dialog to inform user to confirm data (Input data correct ?)
* Once data confirm and save into EEPROM , gray out this item , user will not able to adjust
APPENDIX-4 Edit MODEL NAME and Serial Number
KDL-32R300C U2
34
Edit: MODEL NAME
If the user select this menu, the below editing menu is appeared and adjusting it like "Program Labels" editing way.
XXX-XXXXXXX,
"X" part can change in below way by Remote Commander. Press up/down arrow key to scroll character ("A-Z","0-9","_") and press right arrow key to move the next position.
These number should be affected to "Product Information" in Setting Menu
* After user input data , press <Enter> will pop dialog to inform user to confirm data (Input data correct ?)
* Once data confirm and save into EEPROM , gray out this item , user will not able to adjust
Edit: Serial Number
When you select the SERIAL NUMBER EDIT item in the service mode, use right key to enter edit mode.
SERIAL NUMBER EDIT 0000001
Use the up and down key to edit the first bit of the SERIAL NUMBER (0~9)。
Use the left and right key to switch bit.
SERIAL NUMBER EDIT 0000001
SERIAL NUMBER EDIT 0000001
Use the up and down key to edit the first bit of the SERIAL NUMBER (0~9)。
Use the left and right key to switch bit.
SERIAL NUMBER EDIT 0000001
* After user input data , press <Enter> will pop dialog to inform user to confirm data (Input data correct ?)
* Once data confirm and save into EEPROM , gray out this item , user will not able to adjust
APPENDIX-4 Edit MODEL NAME and Serial Number
KDL-32R300C U2
34
Edit: MODEL NAME
If the user select this menu, the below editing menu is appeared and adjusting it like "Program Labels" editing way.
XXX-XXXXXXX,
"X" part can change in below way by Remote Commander. Press up/down arrow key to scroll character ("A-Z","0-9","_") and press right arrow key to move the next position.
These number should be affected to "Product Information" in Setting Menu
* After user input data , press <Enter> will pop dialog to inform user to confirm data (Input data correct ?)
* Once data confirm and save into EEPROM , gray out this item , user will not able to adjust
Edit: Serial Number
When you select the SERIAL NUMBER EDIT item in the service mode, use right key to enter edit mode.
SERIAL NUMBER EDIT 0000001
Use the up and down key to edit the first bit of the SERIAL NUMBER (0~9)。
Use the left and right key to switch bit.
SERIAL NUMBER EDIT 0000001
SERIAL NUMBER EDIT 0000001
Use the up and down key to edit the first bit of the SERIAL NUMBER (0~9)。
Use the left and right key to switch bit.
SERIAL NUMBER EDIT 0000001
* After user input data , press <Enter> will pop dialog to inform user to confirm data (Input data correct ?)
* Once data confirm and save into EEPROM , gray out this item , user will not able to adjust
APPENDIX-4 Edit MODEL NAME and Serial Number
KDL-32R300C U2