DOWNLOAD Sony KDL-32FA500 / KDL-37FA500 Service Manual ↓ Size: 22.8 MB | Pages: 100 in PDF or view online for FREE

NTSC  American TV Standard
ATSC (8VSB terrestrial)  ATSC compliant 8VSB
QAM on cable:  ANSI/SCTE 07 2000

   

Terrestrial 2-69 

2-69

Cable 1-125 

1-135

75-ohm external terminal for VHF/UHF

LCD (Liquid Crystal Display) Panel

1,366 dots x 768 lines

~ 80cm (KDL-32FA500 Only)
~ 94cm (KDL-37FA500 Only)

Remote Commander RM-YD026
Two Size AA (R6) Batteries
Cable Holder
Operating Instructions
Quick Setup Guide
Warranty Card
Safety and Regulartory Booklet
Software License
DIN Cable

Headphones Plug Adapter
Connecting Cables
Wall-Mount Bracket
 SU-WL500
HDTV Stand
 SU-FL71M
HD15-HD15 Cable
75-ohm Coaxial Cable

All measurements are approximations.

1028 x 608 x 113 mm

35W (7W X 5) + 30W Subwoofer

190W

1 kg

17 kg

21,6 kg

13 kg

17,6 kg

912 x 614 x 309 mm

155W

Less than 1W

65W

146 x 35 mm

300 x 300

200 x 200

912 x 543 x 102 mm

167 x 604 x 184 mm

1028 x 669 x 309 mm

These servicing instructions are for use by qualifi ed service personnel only. To reduce the risk of electric shock, do not perform any servicing other 
than that contained in the operating instructions unless you are qualifi ed to do so.

To avoid dropping the TV and causing serious injury, be sure to follow 
these guidelines:
s Before carrying the TV, disconnect all cables.

s Carrying the large size TV requires two or more people.

s When you carry the TV, place your hand as illustrated and hold it 

securely. Do not put stress on the LCD panel.

s When lifting or moving the TV, hold it firmly from the bottom. Place 

your palm directly under the panel.

s When carrying, do not subject the TV to shocks or vibration, or 

excessive force.

s Place your palm directly underneath, but do not squeeze the

panel’s speaker grill area.

An isolation transformer should be used during any service to avoid possible shock hazard, because of live chassis. The chassis of this receiver is 
directly connected to the ac power line.

!

 SAFETY-RELATED COMPONENT WARNING!!

Components identifi ed by shading and ! mark on the schematic diagrams, exploded views, and in the parts list are critical for safe operation. Replace 
these components with Sony parts whose part numbers appear as shown in this manual or in supplements published by Sony. Circuit adjustments that 
are critical for safe operation are identifi ed in this manual. Follow these procedures whenever critical components are replaced or improper operation is 
suspected. 

There are critical components used in LCD color TVs that are important for safety. These components are identifi ed with shading and 

mark on the schematic diagrams and the electrical parts list. It is essential that these critical parts be replaced only with the part number 
specifi ed in the electrical parts list to prevent electric shock, fi re, or other hazard. 

NOTE: Do not modify the original design without obtaining written permission from the manufacturer or you will void the original parts and 
            labor guarantee. 

When installing the LCD panel on a wall, the LCD panel must be secured using the 4 mounting holes on the rear cover. 

 do not press on the panel or frame edge to avoid the risk of electric shock.

  do not scratch or press on the panel with any sharp objects.

  do not leave the module in high temperatures or in areas of high humidity for an extended period of time.

  do not expose the LCD panel to direct sunlight.

  avoid contact with water. It may cause a short circuit within the module. 

  disconnect the AC adapter when replacing the backlight (CCFL) or inverter circuit. 

(High voltage occurs at the inverter circuit at 650Vrms.) 

  always clean the LCD panel with a soft cloth material.

  use care when handling the wires or connectors of the inverter circuit. Damaging the wires may cause a short. 

  protect the panel from ESD to avoid damaging the electronic circuit (C-MOS). 

The circuit boards used in these models have been processed using
Lead Free Solder. The boards are identified by the LF logo located
close to the board designation e.g. H1 etc [ see example ]. The
servicing of these boards requires special precautions to be taken as
outlined below.

It is strongly recommended to use Lead Free Solder material in order to guarantee optimal quality of new solder joints. 
Lead Free Solder is available under the following part numbers :

Due to the higher melting point of Lead Free Solder the soldering iron tip temperature needs to be set to 370 degrees centigrade. 
This requires soldering equipment capable of accurate temperature control coupled with a good heat recovery characteristics.

For more information on the use of Lead Free Solder, please refer to  http://www.sony-training.com

9

1

-

5

0

0

-

0

4

6

-

7

m

m

3

.

0

g

K

5

2

.

0

0

2

-

5

0

0

-

0

4

6

-

7

m

m

4

.

0

g

K

0

5

.

0

1

2

-

5

0

0

-

0

4

6

-

7

m

m

5

.

0

g

K

0

5

.

0

2

2

-

5

0

0

-

0

4

6

-

7

m

m

6

.

0

g

K

5

2

.

0

3

2

-

5

0

0

-

0

4

6

-

7

m

m

8

.

0

g

K

0

0

.

1

4

2

-

5

0

0

-

0

4

6

-

7

m

m

0

.

1

g

K

0

0

.

1

5

2

-

5

0

0

-

0

4

6

-

7

m

m

2

.

1

g

K

0

0

.

1

6

2

-

5

0

0

-

0

4

6

-

7

m

m

6

.

1

g

K

0

0

.

1