Sony KDL-32EX600 / KDL-40EX600 Service Manual ▷ View online
- 3 -
SECTION GENERAL
The circuit boards used in these models have been processed using
Lead Free Solder. The boards are identified by the LF logo located
close to the board designation e.g. H1 etc [ see example ]. The
servicing of these boards requires special precautions to be taken as
outlined below.
Lead Free Solder. The boards are identified by the LF logo located
close to the board designation e.g. H1 etc [ see example ]. The
servicing of these boards requires special precautions to be taken as
outlined below.
Lead Free Soldered Boards
example
Lead Free Solder material must be used to comply with environmental requirements of new solder joints. Lead Free Solder is available
under the following part numbers :
under the following part numbers :
Due to the higher melting point of Lead Free Solder the soldering iron tip temperature needs to be set to 370 degrees centigrade. This
requires soldering equipment capable of accurate temperature control coupled with a good heat recovery characteristics.
requires soldering equipment capable of accurate temperature control coupled with a good heat recovery characteristics.
For more information on the use of Lead Free Solder, please refer to http://www.sony-training.com
Partnumber
Diameter
Remarks
7-640-005-19
0.3mm
0.25Kg
7-640-005-20
0.4mm
0.50Kg
7-640-005-21
0.5mm
0.50Kg
7-640-005-22
0.6mm
0.25Kg
7-640-005-23
0.8mm
1.00Kg
7-640-005-24
1.0mm
1.00Kg
7-640-005-25
1.2mm
1.00Kg
7-640-005-26
1.6mm
1.00Kg
CAUTION
SECTION GENERAL
How to replace the fuse.
Open the fuse compartment with
a screwdriver blade and replace
the fuse.
Open the fuse compartment with
a screwdriver blade and replace
the fuse.
FUSE
WARNING
(UK Models only)
The flexible mains lead is supplied connected to a B.S. 1363 fused
plug having a fuse of the correct rating for the set. Should the fuse
need to be replaced, use a fuse of the same rating approved by ASTA
to BS 1362, ie one that carries the
plug having a fuse of the correct rating for the set. Should the fuse
need to be replaced, use a fuse of the same rating approved by ASTA
to BS 1362, ie one that carries the
need to be replaced, use a fuse of the same rating approved by ASTA
, ie one that carries the
ASA
T
mark.
mark.
IF THE PLUG SUPPLIED WITH THIS APPLIANCE IS NOT SUITABLE
FOR THE OUTLET SOCKETS IN YOUR HOME, IT SHOULD BE CUT
OFF AND AN APPROPRIATE PLUG FITTED. THE PLUG SEVERED
FROM THE MAINS LEAD MUST BE DESTROYED AS A PLUG WITH
FOR THE OUTLET SOCKETS IN YOUR HOME, IT SHOULD BE CUT
OFF AND AN APPROPRIATE PLUG FITTED. THE PLUG SEVERED
FROM THE MAINS LEAD MUST BE DESTROYED AS A PLUG WITH
BARED WIRES IS DANGEROUS IF ENGAGED IN A LIVE SOCKET.
When an alternative type of plug is used, it should be fitted with the
correct rating fuse, otherwise the circuit should be protected by the
same rating fuse at the distribution board.
correct rating fuse, otherwise the circuit should be protected by the
same rating fuse at the distribution board.
UK PLUG WARNING
LCD PANEL CAUTION
Whilst working on this product, it is not recommended to lay the TV set face down when powered up, as this can result in panel problems.
If it is necessary to power up the TV set when face down, the time should be minimised as much as possible.
If it is necessary to power up the TV set when face down, the time should be minimised as much as possible.
- 4 -
SPECIFICATIONS
Model name
KDL-
46EX4xx
46EX4xx
KDL-
40BX4/EX4/
EX6/NX5xx
40BX4/EX4/
EX6/NX5xx
KDL-
37EX4xx
37EX4xx
KDL-32BX3/
BX4/EX3/EX4/
EX6/NX5xx
BX4/EX3/EX4/
EX6/NX5xx
KDL-
26EX3xx
26EX3xx
KDL-
22EX3xx
22EX3xx
System
Panel System
Panel System
LCD (Liquid Crystal Display) Panel
TV System
Depending on your country/region selection
Analogue: B/G/H, D/K, L, I
Digital: DVB-T, DVB-C
Colour/Video System
Analogue: PAL, PAL60 (only video input), SECAM, NTSC3.58, NTSC4.43 (only video input)
Digital: MPEG-2 MP@ML/HL, H.264/MPEG-4 AVC [email protected], [email protected]
Channel Coverage
Analogue: 46.25 - 855.25 MHz
Digital: VHF/UHF
Sound Output
10 W + 10 W (RMS)
8 W + 8 W
(RMS)
5 W + 5 W
(RMS)
Input/Output jacks
Aerial
Aerial
75 ohm external terminal for VHF/UHF
/
AV1*
1
21-pin scart connector including audio/video input, RGB input, S-Video input, and Analogue TV audio/video
output.
/
AV2*
2
21-pin scart connector including audio/video input, RGB input, S-Video input, and audio/video output.
COMPONENT IN
Supported formats: 1080p, 1080i, 720p, 576p, 576i, 480p, 480i
Y: 1 Vp-p, 75 ohms, 0.3V negative sync/P
B
/C
B
: 0.7 Vp-p, 75 ohms/
P
R
/C
R
: 0.7 Vp-p, 75 ohms
COMPONENT IN
Audio input (phono jacks)
HDMI IN 1, 2, 3, 4
Video: 1080p, 1080p24, 1080i, 720p, 576p, 576i, 480p, 480i
Audio: Two channel linear PCM
32, 44.1 and 48 kHz, 16, 20 and 24 bits, Dolby Digital
PC (see page 6)
Analogue audio (minijack) (HDMI 1 only)
AV3
Video input (phono jack)
AV3
Audio input (phono jacks)
DIGITAL AUDIO
OUT (OPTICAL)
Digital optical jack (Two channel linear PCM, Dolby Digital)
Audio output (Left/Right) (phono jacks)
PC IN
PC Input (15 Dsub) (see page 6)
G: 0.7 Vp-p, 75 ohms, non Sync on Green/B: 0.7 Vp-p, 75 ohms/
R: 0.7 Vp-p, 75 ohms, H/V Sync: TTL level
PC audio input (minijack)
i
Headphones jack
USB port
CAM (Conditional Access Module) slot
USB port
CAM (Conditional Access Module) slot
Power and others
Power Requirements
Power Requirements
220–240 V AC, 50 Hz
Screen Size (measured
diagonally)
46 inches /
Approx. 117 cm
40 inches /
Approx. 102 cm
37 inches /
Approx. 94 cm
32 inches /
Approx. 80 cm
26 inches /
Approx. 66 cm
22 inches /
Approx. 55 cm
Display Resolution
1,920 dots (horizontal) × 1,080 lines (vertical) (KDL-46EX4xx, KDL-40BX4/EX4/EX6/NX5xx, KDL-
37EX4xx, KDL-32BX4/EX4/EX6/NX5xx)
1,366 dots (horizontal) × 768 lines (vertical) (KDL-32BX3/EX3xx, KDL-26EX3xx, KDL-22EX3xx)
Power
consumption
in “Home”/
“Standard”
mode
142 W
110 W
66.0 W (KDL-
40EX6xx)
95.0 W
73.0 W
58.0 W (KDL-
32EX6xx)
52.0 W
39.0 W
in “Shop”/
“Vivid”
mode
183 W
146 W
80 W (KDL-
40EX6xx)
120 W
94 W
70 W (KDL-
32EX6xx)
62 W
46 W
- 5 -
*
1
AV1 outputs available only for analogue TV.
*
2
AV2 outputs watching screen (except PC, HDMI, Component, USB).
*
3
Specified standby power is reached after the TV finishes necessary internal processes.
*
4
4 hours a day and 365 days a year.
Design and specifications are subject to change without notice.
Standby Power
Consumption*
3
0.19 W
Off mode Power
Consumption
0.18 W
Average anual energy
consumption*
4
207 kWh
161 kWh
96 kWh (KDL-
40EX6xx)
139 kWh
107 kWh
85 kWh (KDL-
32EX6xx)
76 kWh
57 kWh
Dimensions
(w × h × d)
(Approx.)
(with stand)
112.7 x 71.1 x
29.4 cm
102.3 x 66.5 x
31.0 cm (KDL-
40NX5xx)
99.6 x 63.5 x 25.0
cm (KDL-
40BX4xx)
99.2 x 63.5 x 25.0
cm (KDL-
40EX4xx)
95.2 x 61.3 x
25.0 cm (KDL-
40EX6xx)
92.1 x 59.9 x
25.1 cm
82.5 x 55.4 x 26.0
cm (KDL-
32NX5xx)
80.4 x 53.2 x 22.0
cm (KDL-32BX3/
BX4xx)
80.0 x 53.2 x 22.0
cm (KDL-32EX3/
EX4xx)
76.4 x 50.7 x 25.0
cm (KDL-
32EX6xx)
67.2 x 45.9 x
22.0 cm
55.1 x 40.2 x
21.5 cm
(without
stand)
112.7 x 67.4 x
10.2 cm
102.3 x 62.8 x
10.0 cm (KDL-
40NX5xx)
99.6 x 59.8 x 9.9
cm (KDL-
40BX4xx)
99.2 x 59.8 x 10.0
cm (KDL-
40EX4xx)
95.2 x 58.1 x 7.4
cm (KDL-
40EX6xx)
92.1 x 56.4 x 9.8
cm
82.5 x 51.7 x 10.2
cm (KDL-
32NX5xx)
80.4 x 49.7 x 9.6 cm
(KDL-32BX3/
BX4xx)
80.0 x 49.7 x 9.7 cm
(KDL-32EX3/
EX4xx)
76.4 x 47.5 x 7.3 cm
(KDL-32EX6xx)
67.2 x 42.3 x 9.9
cm
55.1 x 36.7 x 8.2
cm
Mass
(Approx.)
(with stand)
20.4 kg
22.4 kg (KDL-
40NX5xx)
15.6 kg (KDL-
40BX4xx)
15.9 kg (KDL-
40EX4xx)
14.9 kg (KDL-
40EX6xx)
13.6 kg
15.5 kg (KDL-
32NX5xx)
10.7 kg (KDL-
32BX3/BX4xx)
11.0 kg (KDL-
32EX3/EX4xx)
11.1 kg (KDL-
32EX6xx)
8.8 kg
6.6 kg
(without
stand)
18.1 kg
19.2 kg (KDL-
40NX5xx)
13.6 kg (KDL-
40BX4xx)
13.9 kg (KDL-
40EX4xx)
12.7 kg (KDL-
40EX6xx)
11.6 kg
13.0 kg (KDL-
32NX5xx)
9.2 kg (KDL-
32BX3/BX4xx)
9.5 kg (KDL-
32EX3/EX4xx)
9.1 kg (KDL-
32EX6xx)
7.3 kg
6.0 kg
Model name
KDL-
46EX4xx
KDL-
40BX4/EX4/
EX6/NX5xx
KDL-
37EX4xx
KDL-32BX3/
BX4/EX3/EX4/
EX6/NX5xx
KDL-
26EX3xx
KDL-
22EX3xx
- 6 -
PC Input Signal Reference Chart for PC IN
• This TV’s PC input does not support Sync on Green or Composite Sync.
• This TV’s PC input does not support interlaced signals.
• This TV’s PC input supports signals in the above chart with a 60 Hz vertical frequency.
PC Input Signal Reference Chart for HDMI IN 1, 2, 3 and 4
Signals Horizontal (Pixel) Vertical (Line)
Horizontal
frequency
(kHz)
Vertical
frequency (Hz) Standard
VGA
640
480
31.5
60
VGA
SVGA
800
600
37.9
60
VESA Guidelines
XGA
1024
768
48.4
60
VESA Guidelines
WXGA
1280
768
47.4
60
VESA
WXGA
1280
768
47.8
60
VESA
WXGA
1360
768
47.7
60
VESA
SXGA
1280
1024
64
60
VESA
UXGA
1600
1200
75
60
VESA
HDTV
1920
1080
67.5
60
EIA
Signals Horizontal (Pixel) Vertical (Line)
Horizontal
frequency
(kHz)
Vertical
frequency (Hz) Standard
VGA
640
480
31.5
60
VGA
SVGA
800
600
37.9
60
VESA Guidelines
XGA
1024
768
48.4
60
VESA Guidelines
WXGA
1280
768
47.4
60
VESA
WXGA
1280
768
47.8
60
VESA
WXGA
1360
768
47.7
60
VESA
SXGA
1280
1024
64
60
VESA