DOWNLOAD Sony KDL-32EX600 / KDL-40EX600 / KDL-46EX600 (serv.man2) Service Manual ↓ Size: 24.82 MB | Pages: 38 in PDF or view online for FREE

Model
KDL-32EX600 KDL-40EX600 KDL-46EX600 (serv.man2)
Pages
38
Size
24.82 MB
Type
PDF
Document
Service Manual
Brand
Device
TV
File
kdl-32ex600-kdl-40ex600-kdl-46ex600-sm2.pdf
Date

Sony KDL-32EX600 / KDL-40EX600 / KDL-46EX600 (serv.man2) Service Manual ▷ View online

3
KDL-32EX600/40EX600/46EX600
KDL-32EX600/40EX600/46EX600
SAFETY-RELATED COMPONENT WARNING
There are critical components used in LCD color TVs that are important for safety. These components are identifi ed with shading and 
!
 
mark on the schematic diagrams and the electrical parts list. It is essential that these critical parts be replaced only with the part number 
specifi ed in the electrical parts list to prevent electric shock, fi re, or other hazard. 
NOTE: Do not modify the original design without obtaining written permission from the manufacturer or you will void the original parts and 
            labor guarantee. 
USE CAUTION WHEN HANDLING THE LCD PANEL
When repairing the LCD panel, be sure you are grounded by using a wrist band.
When installing the LCD panel on a wall, the LCD panel must be secured using the 4 mounting holes on the rear cover. 
To avoid damaging the LCD panel:
do not press on the panel or frame edge to avoid the risk of electric shock.
  do not scratch or press on the panel with any sharp objects.
  do not leave the module in high temperatures or in areas of high humidity for an extended period of time.
  do not expose the LCD panel to direct sunlight.
  avoid contact with water. It may cause a short circuit within the module. 
  disconnect the AC adapter when replacing the backlight (CCFL) or inverter circuit. 
(High voltage occurs at the inverter circuit at 650Vrms.) 
  always clean the LCD panel with a soft cloth material.
  use care when handling the wires or connectors of the inverter circuit. Damaging the wires may cause a short. 
  protect the panel from ESD to avoid damaging the electronic circuit (C-MOS). 
  during the repair, DO NOT leave the Power On for more than 1 hour while the TV is face down on a cloth.
 
 
 
LEAKAGE CURRENT HOT CHECK CIRCUIT
4
KDL-32EX600/40EX600/46EX600
KDL-32EX600/40EX600/46EX600
The circuit boards used in these models have been processed using 
Lead Free Solder. The boards are identified by the LF logo located 
close to the board designation e.g. H1 etc [ see example ]. The 
servicing of these boards requires special precautions to be taken as 
outlined below. 
example
It is strongly recommended to use Lead Free Solder material in order to guarantee optimal quality of new solder joints.  
Lead Free Solder is available under the following part numbers : 
Due to the higher melting point of Lead Free Solder the soldering iron tip temperature needs to be set to 370 degrees centigrade. 
This requires soldering equipment capable of accurate temperature control coupled with a good heat recovery characteristics. 
For more information on the use of Lead Free Solder, please refer to  
 http://www.sony-training.com
7
0
7
0
7
0
7
0
7
0
7
1
7
1
7
1
5
KDL-32EX600/40EX600/46EX600
KDL-32EX600/40EX600/46EX600
SAFETY CHECK-OUT
After correcting the original service problem, perform the following 
safety checks before releasing the set to the customer:
1.  Check the area of your repair for unsoldered or poorly soldered 
connections. Check the entire board surface for solder splashes and 
bridges.
2.  Check the interboard wiring to ensure that no wires are “pinched” or 
touching high-wattage resistors.
3.  Check that all control knobs, shields, covers, ground straps, and 
mounting hardware have been replaced. Be absolutely certain that 
you have replaced all the insulators.
4.  Look for unauthorized replacement parts, particularly transistors, 
that were installed during a previous repair. Point them out to the 
customer and recommend their replacement.
5.  Look for parts which, though functioning, show obvious signs of 
deterioration. Point them out to the customer and recommend their 
replacement.
6.  Check the line cords for cracks and abrasion. Recommend the 
replacement of any such line cord to the customer.
7.  Check the antenna terminals, metal trim, “metallized” knobs, screws, 
and all other exposed metal parts for AC leakage. Check leakage as 
described below.
Leakage Test
The AC leakage from any exposed metal part to earth ground and 
from all exposed metal parts to any exposed metal part having a 
return to chassis, must not exceed 0.5 mA (500 microamperes). 
Leakage current can be measured by any one of three methods.
1.  A commercial leakage tester, such as the Simpson 229 or RCA 
WT-540A. Follow the manufacturers’ instructions to use these 
instructions.
2.  A battery-operated AC milliampmeter. The Data Precision 245 
digital multimeter is suitable for this job.
3.  Measuring the voltage drop across a resistor by means of a VOM 
or battery-operated AC voltmeter. The “limit” indication is 0.75 
V, so analog meters must have an accurate low voltage scale. 
The Simpson’s 250 and Sanwa SH-63TRD are examples of 
passive VOMs that are suitable. Nearly all battery-operated digital 
multimeters that have a 2 VAC range are suitable (see Figure A).
How to Find a Good Earth Ground
A cold-water pipe is a guaranteed earth ground; the cover-plate 
retaining screw on most AC outlet boxes is also at earth ground. If the 
retaining screw is to be used as your earth ground, verify that it is at 
ground by measuring the resistance between it and a cold-water pipe 
with an ohmmeter. The reading should be zero ohms.
If a cold-water pipe is not accessible, connect a 60- to 100-watt 
trouble- light (not a neon lamp) between the hot side of the receptacle 
and the retaining screw. Try both slots, if necessary, to locate the hot 
side on the line; the lamp should light at normal brilliance if the screw 
is at ground potential (see Figure B).
To Exposed Metal
Parts on Set
0.15 μF
Earth Ground
AC
Voltmeter
(0.75V)
Trouble Light
AC Outlet Box
Ohmmeter
Cold-water Pipe
Figure A. Using an AC voltmeter to check AC leakage.
Figure B. Checking for earth ground.
6
KDL-32EX600/40EX600/46EX600
KDL-32EX600/40EX600/46EX600
SECTION 1:  DIAGRAMS
1-1.  CIRCUIT BOARDS LOCATION
1-2.  PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS INFORMATION
All voltages are in V.
S : Measurement impossibility.
: B+line.
: B-line.  (Actual measured value may be different).
: signal path. (RF)
Circled numbers are waveform references.
The components identifi ed by shading and 
!
 symbol are critical for safety. Replace 
only with part number specifi ed. 
The symbol 
 indicates a fast operating fuse and is displayed on the component 
side of the board. Replace only with fuse of the same rating as marked.
Les composants identifi es per un trame et une marque 
!
 sont critiques pour la 
securite.  Ne les remplacer que par une piece portant le numero specifi e.
Le symbole 
 indique une fusible a action rapide. Doit etre remplace par une 
fusible de meme yaleur, comme maque.
NOTE: The components identifi ed by a red outline and a   mark contain confi dential 
information. Specifi c instructions must be adhered to whenever these components 
are repaired and/or replaced. 
See Appendix A: Encryption Key Components in the back of this manual. 
All capacitors are in μF unless otherwise noted. pF : μμF 50WV or 
less are not indicated except for electrolytics and tantalums.
All electrolytics are in 50V unless otherwise specifi ed.
All resistors are in ohms.  k
=1000, M=1000k
Indication of resistance, which does not have one for rating 
electrical power, is as follows: 
Pitch : 5mm 
 
 
    Rating 
electrical 
power 
1
/
 4 
W
1
/
 4 
W in resistance, 
1
/
10 
W and 
1
/
16 
W in chip resistance.
: nonfl ammable resistor
 : fusible resistor
 : internal component
 : panel designation and adjustment for repair
 : earth ground
 : earth-chassis
All variable and adjustable resistors have characteristic curve B, 
unless otherwise noted.
Readings are taken with a color-bar signal input.
Readings are taken with a 10M
 digital multimeter.
Voltages are DC with respect to ground unless otherwise noted.
Voltage variations may be noted due to normal production 
tolerances.
GE3B (KDL-32EX600/40EX600 ONLY)
GE2C (KDL-46EX600 ONLY)
SWITCH UNIT
H2
A
Page of 38
Display

Sony KDL-32EX600 / KDL-40EX600 / KDL-46EX600 (serv.man2) Service Manual ▷ Download

  • DOWNLOAD Sony KDL-32EX600 / KDL-40EX600 / KDL-46EX600 (serv.man2) Service Manual ↓ Size: 24.82 MB | Pages: 38 in PDF or view online for FREE
  • Here you can View online or download the Service Manual for the Sony KDL-32EX600 / KDL-40EX600 / KDL-46EX600 (serv.man2) in PDF for free, which will help you to disassemble, recover, fix and repair Sony KDL-32EX600 / KDL-40EX600 / KDL-46EX600 (serv.man2) TV. Information contained in Sony KDL-32EX600 / KDL-40EX600 / KDL-46EX600 (serv.man2) Service Manual (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.