Sony KDL-32BX353 / KDL-32BX354 / KDL-40BX453 / KDL-46BX453 Service Manual ▷ View online
KDL-32BX353/32BX354/40BX453/46BX453 29
SECTION 5 - UPDATES AND ADJUSTMENTS
COMPLETING SERVICE REQUIREMENTS WHEN
REPLACING THE LCD PANEL
The following must be performed after replacing the LCD Panel.
;
View the Status Information
;
Verify the Panel ID Code
;
Reset the Panel Operation Time
1. TV must be in Standby mode.
2. Press the following buttons on the
2. Press the following buttons on the
Remote Commander within a
second of each other:
DISPLAY
Channel 5
Volume +
POWER
Sound Adjustment
>>
Wide Band Tuning
>>
Range Scan…
>>
Self diagnosis history
>>
Status Information…
>>
LVDS Spectrum(%0)
<[
20
]>
DPMS
Off
Low of HPD
5
TVD_MCDONE_CNT
20
Demo Special
>>
Bypass AVI Info Detect
On
Panel Selection
<[
13_FHD_SLCD_40
]>
UART Selection
No Log
SERIAL NUMBER EDIT
5000001
MODEL NAME EDIT
KDL-40BX453
[</>]Set [Home] Exit
Service Mode
VIEWING THE STATUS INFORMATION
After replacing the LCD Panel you MUST UPDATE the SOFTWARE to the
latest version. Verify the latest software is installed before proceeding to the
service adjustments.
Whenever the LCD Panel is replaced, the software must be updated so that
Whenever the LCD Panel is replaced, the software must be updated so that
the new panel syncs with the Main Board. If a message displays indicating
the latest software is already installed, proceed to Resetting the LCD Panel
to Update the Software.
3. For instructions refer to the section
“Viewing the Status
Information” on page 24.
4. Do one of the following:
a. If the latest software is installed, proceed to
Verifying the
Panel ID Code.
b. If the latest software is not installed, update the software and
then proceed to
Verifying the Panel ID Code.
VERIFYING THE PANEL ID CODE
5. Press until
Panel Selection is selected.
Sound Adjustment
>>
Wide Band Tuning
>>
Range Scan…
>>
Self diagnosis history
>>
Status Information…
>>
LVDS Spectrum(%0)
<[
20
]>
DPMS
Off
Low of HPD
5
TVD_MCDONE_CNT
20
Demo Special
>>
Bypass AVI Info Detect
On
Panel Selection
<[
13_FHD_SLCD_40
]>
UART Selection
No Log
SERIAL NUMBER EDIT
5000001
MODEL NAME EDIT
KDL - 40BX453
[</>]Set [Home] Exit
Service Mode
KDL-32BX353/32BX354/40BX453/46BX453 30
SECTION 5 - UPDATES AND ADJUSTMENTS
6. Using the table below, verify the correct Panel Code for the
Panel ID.
Model Name
Panel Code
Panel Type
Panel ID
KDL-32BX353
KDL-32BX354
KDL-40BX453
KDL-46BX453
KDL-32BX354
KDL-40BX453
KDL-46BX453
LTY[Z]320AN04
12_WXGA_SLCD_32
SLCD
LTY[Z]400HM09
LTY[Z]460HN06
LTY[Z]460HN06
SLCD
SLCD
SLCD
12_WXGA_SLCD_32
13_FHD_SLCD_40
14_FHD_SLCD_46
14_FHD_SLCD_46
SLCD
LTY[Z]320AN04
7. Proceed to
Resetting the Panel Operation Time.
RESETTING PANEL OPERATION TIME
8. Press to select
Self diagnosis history.
9. On the
Self Check screen, identify the Panel Operation Time
location.
Back
<<
002
MAIN_ POWER
000
003
DC_ALERT1
000
003
AUDIO_PROT
000
004
BALANCER_ERR
000
005
TCON_ERR
000
005
PANEL_ID_NVM_ERR
000
006
BACKLIGHT_ERR
000
007
TEMP_ERR
000
00150
00075
00030
[Home] Exit
SELF CHECK
TOTAL OPERATION
TIME
PANEL OPERATION
TIME
BOOT COUNT
10. Press
7
0
.
11. Verify
Panel Operation Time has been changed to 00000.
Back
<<
002 MAIN_ POWER
000
003 DC_ALERT1
000
003 AUDIO_PROT
000
004 BALANCER_ERR
000
005 TCON_ERR
000
005 PANEL_ID_NVM_ERR
000
006 BACKLIGHT_ERR
000
007 TEMP_ERR
000
00150
00075
00000
[Home] Exit
SELF CHECK
12. To exit the
Self Check, press
HOME
.
KDL-32BX353/32BX354/40BX453/46BX453 31
Sony Corporation
Sony LCSC
Technical Services
Service Publication Department
9-883-876-02
English
2012CJ74WEB-1
© 2012.3
is a trademark of Sony Electronics
Reproduction in whole or part without written permission is prohibited. All rights reserved
KDL-32BX353/32BX354/40BX453/46BX453 A-1
APPENDIX A: ENCRYPTION KEY COMPONENTS
Encryption key components developed by Sony Corporation contain confidential information, and shall be handled under the non-disclosure obligations
provided in the applicable agreement with Sony Corporation (and/or its subsidiary).
As part of this agreement specific instructions must be adhered to whenever a Circuit Board containing encryption key components is repaired and/or replaced
As part of this agreement specific instructions must be adhered to whenever a Circuit Board containing encryption key components is repaired and/or replaced
pursuant to the following:
1. In the service manual the Circuit Board(s) containing encryption key components shall be identified with a red outline and a .
2. Only repair boards or components listed in the service manual shall be utilized for replacement and/or repair.
3. Disassembly, decryption, or reverse-engineering component(s) is strictly prohibited.
4. Any board in which the Servicer replaces an encryption key component must be placed back into the set it orignally came from and the replaced
2. Only repair boards or components listed in the service manual shall be utilized for replacement and/or repair.
3. Disassembly, decryption, or reverse-engineering component(s) is strictly prohibited.
4. Any board in which the Servicer replaces an encryption key component must be placed back into the set it orignally came from and the replaced
defective component MUST BE DESTROYED. Boards cannot be swapped.
5. If a Circuit Board identified with a red outline and a in the service manual is deemed to be defective:
a. and if a core charge is imposed and is covered under the product warranty, the defective un-repaired or modified board MUST BE RETURNED
to Sony.
b. and if the core charge is NOT covered under the product warranty, the defective un-repaired or modified board MUST BE DESTROYED.
6. If a unit is destroyed (such as field scrap), the Circuit Board identified with a
red outline and a in the service manual MUST BE DESTROYED.