Sony KDL-26V4000 / KDL-26V4220 / KDL-26V4230 / KDL-26V4240 / KDL-32V4000 / KDL-32V4200 / KDL-32V4210 / KDL-32V4220 / KDL-32V4230 / KDL-32V4240 / KDL-37V4000 / KDL-37V4220 / KDL-37V4230 / KDL-37V4240 Service Manual ▷ View online
- 5 -
CONNECTORS
21 Pin Connector (SCART)
_
_
Red input
0.7 +/- 3dB, 75 ohms, positive
_
(S signal Chroma
Connected
Not Connected (open) * at 20Hz - 20kHz
Pin No
1
2
Signal
Signal level
1
Audio output B
(right)
(right)
Standard level : 0.5V rms
Output impedence : Less than 1kohm*
Output impedence : Less than 1kohm*
2
Audio input B
(right)
(right)
Standard level : 0.5V rms
Output impedence : More than 10kohm*
Output impedence : More than 10kohm*
3
Audio output A
(left)
(left)
Standard level : 0.5V rms
Output impedence : Less than 1kohm*
Output impedence : Less than 1kohm*
4
Ground (audio)
5
Ground (blue)
6
Audio input A
(left)
(left)
Standard level : 0.5V rms
Output impedence : More than 10kohm*
Output impedence : More than 10kohm*
7
Blue input
0.7 +/- 3dB, 75 ohms positive
8
Function select
(AV control)
(AV control)
High state (9.5-12V) : Part mode
Low state (0-2V) : TV mode
Input impedence : More than 10K ohms
Input capacitance : Less than 2nF
Low state (0-2V) : TV mode
Input impedence : More than 10K ohms
Input capacitance : Less than 2nF
9
Ground (green)
10
AVlink
11
Green
Green signal : 0.7 +/- 3dB, 75 ohms,
positive
positive
12
Open
13
Ground (red)
14
Ground (blanking)
15
input)
0.3 +/- 3dB, 75 ohms, positive
16
Blanking input
(Ys signal)
(Ys signal)
High state (1-3V) Low state (0-0.4V)
Input impedence : 75 ohms
Input impedence : 75 ohms
17
Ground (video
output)
output)
18
Ground (video
input)
input)
19
Video output
1V +/- 3dB, 75ohms, positive sync 0.3V
(-3+10dB)
(-3+10dB)
20
Video input
1V +/- 3dB, 75ohms, positive sync 0.3V
(-3+10dB)
Video input
Y (S signal)
1V +/- 3dB, 75ohms, positive sync 0.3V
(-3+10dB)
(-3+10dB)
21
Common ground
(plug, shield)
(plug, shield)
- -
- -
19
17
15
13
11
9
7
5
3
1
20
18
16
14
12
10
8
6
4
2
21
How to replace the fuse.
Open the fuse compartment with
a screwdriver blade and replace
the fuse.
Open the fuse compartment with
a screwdriver blade and replace
the fuse.
FUSE
WARNING
(UK Models only)
The flexible mains lead is supplied connected to a B.S. 1363 fused
plug having a fuse of the correct rating for the set. Should the fuse
need to be replaced, use a fuse of the same rating approved by ASTA
to BS 1362, ie one that carries the
plug having a fuse of the correct rating for the set. Should the fuse
need to be replaced, use a fuse of the same rating approved by ASTA
to BS 1362, ie one that carries the
ASA
T
mark.
IF THE PLUG SUPPLIED WITH THIS APPLIANCE IS NOT SUITABLE
FOR THE OUTLET SOCKETS IN YOUR HOME, IT SHOULD BE CUT
OFF AND AN APPROPRIATE PLUG FITTED. THE PLUG SEVERED
FROM THE MAINS LEAD MUST BE DESTROYED AS A PLUG WITH
BARED WIRES IS DANGEROUS IF ENGAGED IN A LIVE SOCKET.
FOR THE OUTLET SOCKETS IN YOUR HOME, IT SHOULD BE CUT
OFF AND AN APPROPRIATE PLUG FITTED. THE PLUG SEVERED
FROM THE MAINS LEAD MUST BE DESTROYED AS A PLUG WITH
BARED WIRES IS DANGEROUS IF ENGAGED IN A LIVE SOCKET.
When an alternative type of plug is used, it should be fitted with the
correct rating fuse, otherwise the circuit should be protected by the
same rating fuse at the distribution board.
correct rating fuse, otherwise the circuit should be protected by the
same rating fuse at the distribution board.
UK PLUG WARNING
- 6 -
HDMI Connector
Rear Connection Panel
Side Connection Panel
15 Pin D Sub Connector (PC)
1
Pin No
Signal Assignment
Pin No
Signal Assignment
1
TMDS Data2+
11
TMDS Clock Shield
2
TMDS Data2 Shield
12
TMDS Clock-
3
TMDS Data2-
13
CEC
4
TMDS Data1+
14
Reserved (N.C. on device)
5
TMDS Data1 Shield
15
SCL
6
TMDS Data1-
16
SDA
7
TMDS Data0+
17
DDC/CEC Ground
8
TMDS Data0 Shield
18
+5V Power
9
TMDS Data0-
19
Hot Plug Detect
10
TMDS Clock+
Pin No
Signal Assignment
Pin No
Signal Assignment
1
Red Out
9
+5V DC
2
Green Out
10
Sync Return (Ground)
3
Blue Out
11
Monitor ID0 in Display
4
Unused
12
DCC Serial Data
5
Ground
13
Horizontal Sync
6
Red Return
14
Vertical Sync
7
Green Return (Ground)
15
DCC Serial Clock
8
Blue Return (Ground)
- 7 -
SE2AG SELF DIAGNOSTIC SOFTWARE
The identification of errors within the SE2AG chassis is triggered in one of two ways :- 1: Busy or 2: Device failure to respond to IIC. In the
event of one of these situations arising the software will first try to release the bus if busy (Failure to do so will report with a continuous
flashing LED) and then communicate with each device in turn to establish if a device is faulty. If a device is found to be faulty the relevant
device number will be displayed through the LED (Series of flashes which must be counted).
event of one of these situations arising the software will first try to release the bus if busy (Failure to do so will report with a continuous
flashing LED) and then communicate with each device in turn to establish if a device is faulty. If a device is found to be faulty the relevant
device number will be displayed through the LED (Series of flashes which must be counted).
LED Error Codes
Number of LED
Flashes
Error Description
Checked
Action
02
Balancer error.
In normal mode.
Goes into standby.
03
DC error.
In normal mode.
Goes into standby.
04
Inverter error.
In normal mode.
Goes into standby.
05
NVM error.
In initialisation state.
Goes into standby.
06
IIC error.
In normal mode.
Goes into standby.
07
HDMI error.
In normal mode.
Adds error to error menu.
08
Digital error.
In normal mode.
Adds error to error menu.
09
Tuner error
In initialisation state.
Adds error to error menu.
10
SP error
In initialisation state.
Adds error to error menu.
13
RTC error
In initialisation state.
Adds error to error menu.
- 8 -
SECTION 2 DISASSEMBLY
2-1. Rear Cover Removal
2-2. Stand Removal
=>
=>
=>
=>
=>
=>
=>
=>
2-3. Loudspeaker Removal
2-4. Side Jack Bracket Assy Removal
To remove the ‘Rear cover’ remove the 25 fixing screws indicated
and pull the rear cover gently backwards away from the TV set.
and pull the rear cover gently backwards away from the TV set.
Screw Part number(s) and Description(s)
1) 2-580-640-01 SCREW, +BVTP2 4X16
2) 7-685-648-79 SCREW, +BVTP 3X12 TYPE2 IT-3
3) 2-580-607-01 SCREW, +PSW M5X12
2) 7-685-648-79 SCREW, +BVTP 3X12 TYPE2 IT-3
3) 2-580-607-01 SCREW, +PSW M5X12
=>
1
=>
1
=>
1
=>
1
1
1
1
1
1
3
3
3
=>
2
=>
3
=>
=>
=>
=>
1
=>
1
=>
=>
To remove the ‘Stand’ remove the 3 fixing screws indicated.
Screw Part number(s) and Description(s)
2-580-608-01 SCREW, +PSW M5X16
Clips
To remove the ‘Side jack bracket assy’ release the 2 clips circled.
=>
3
=>
3
=>
1
1
=>
To remove the ‘Loudspeaker’ from its housing disconnect the speaker
cables, remove the 4 screws circled and then pull the loudspeaker
gently backwards away from the back of the TV set.
cables, remove the 4 screws circled and then pull the loudspeaker
gently backwards away from the back of the TV set.
Screws
=>
1
=>
1
1
=>
=>
1
=>
1
Click on the first or last page to see other KDL-26V4000 / KDL-26V4220 / KDL-26V4230 / KDL-26V4240 / KDL-32V4000 / KDL-32V4200 / KDL-32V4210 / KDL-32V4220 / KDL-32V4230 / KDL-32V4240 / KDL-37V4000 / KDL-37V4220 / KDL-37V4230 / KDL-37V4240 service manuals if exist.