Sony KDL-26V4000 / KDL-26V4220 / KDL-26V4230 / KDL-26V4240 / KDL-32V4000 / KDL-32V4200 / KDL-32V4210 / KDL-32V4220 / KDL-32V4230 / KDL-32V4240 / KDL-37V4000 / KDL-37V4220 / KDL-37V4230 / KDL-37V4240 Service Manual ▷ View online
- 4 -
SPECIFICATIONS
Television System
Channel Coverage
Colour/Video System
Analogue:
Depending on your country/region
B/G/H, D/K, L, I
Depending on your country/region
B/G/H, D/K, L, I
Digital:
DVB-T/DVB-C
DVB-T/DVB-C
Analogue: 48.25 - 855.25 MHz
Digital: VHF/UHF
Analogue:
PAL, SECAM
NTSC 3.58/4.43 (Video in only)
PAL, SECAM
NTSC 3.58/4.43 (Video in only)
Digital:
MPEG-2 MP@ML
MPEG-2 MP@ML
Picture Size
LCD(Liquid Crystal Display) Panel
Approx 66.0cm (26 inches)
Approx 81.3cm (32 inches)
Approx 94.0cm (37 inches)
Approx 81.3cm (32 inches)
Approx 94.0cm (37 inches)
Sound Output
Right and Left speaker
2 x 10W (RMS)
Input/Output Terminals [REAR]
General Specifications
1: 21-pin Euro connector
(CENELEC standard)
Inputs for Audio and Video signals.
Inputs for RGB.
Inputs for RGB.
Outputs of TV Video and Audio
signals.
signals.
Power Requirements
220 - 240V
Power Consumption/
Standby
(26 inches):
Approx 61W/0.7W (Home mode)
Approx 87W/0.7W (Shop mode)
Approx 87W/0.7W (Shop mode)
(32 inches):
Approx 86W/0.7W (Home mode)
Approx 129W/0.7W (Shop mode)
Approx 129W/0.7W (Shop mode)
(37 inches):
Approx 106W/0.6W (Home mode)
Approx 155W/0.6W (Shop mode)
Approx 155W/0.6W (Shop mode)
2: 21-pin Euro connector
(CENELEC standard)
(CENELEC standard)
Inputs for Audio and Video signals.
Inputs for RGB.
Inputs for RGB.
Outputs of Video and Audio signals
(Selectable). SmartLink interface.
(Selectable). SmartLink interface.
Dimensions
(26 inches):
Approx 659x505x242mm (With stand)
Approx 659x466x95mm (Without stand)
Approx 659x466x95mm (Without stand)
(32 inches):
Approx 794x577x242mm (With stand)
Approx 794x540x99mm (Without stand)
Approx 794x540x99mm (Without stand)
(37 inches):
Approx 920x649x279mm (With stand)
Approx 920x610x110mm (Without stand)
Approx 920x610x110mm (Without stand)
Weight
Approx 12.5kg (26 inches with stand)
Approx 10.0kg (26 inches without stand)
Approx 15.5kg (32 inches with stand)
Approx 13.0kg (32 inches without stand)
Approx 20.5kg (37 inches with stand)
Approx 17.5kg (37 inches without stand)
Approx 10.0kg (26 inches without stand)
Approx 15.5kg (32 inches with stand)
Approx 13.0kg (32 inches without stand)
Approx 20.5kg (37 inches with stand)
Approx 17.5kg (37 inches without stand)
Component In
Supported formats:1080i, 720p,
576p, 576i, 480p, 480i
Y:1 Vp-p, 75 ohms, 0.3V negative
sync
576p, 576i, 480p, 480i
Y:1 Vp-p, 75 ohms, 0.3V negative
sync
PB/CB:0.7 Vp-p, 75 ohms
PR/CR:0.7 V p-p, 75 ohms
PR/CR:0.7 V p-p, 75 ohms
Audio input:Phono jacks
Other Features
Intergrated digital TV Tuner DVB-T/C, HD Ready,
High Picture Quality, Bravia Engine, Dynamic
High Picture Quality, Bravia Engine, Dynamic
Contrast, Virtual Dolby Surround, BBE-Viva,
PC Input, 3 HDMI Inputs.
HDMI Inputs
Video:1080i, 720p, 576p, 576i,
480p, 480i
Audio:Two channel linear PCM
32, 44.1 and 48kHz,
16, 20 and 24 bits
Analogue audio input:Minijack
480p, 480i
Audio:Two channel linear PCM
32, 44.1 and 48kHz,
16, 20 and 24 bits
Analogue audio input:Minijack
(HDMI IN 3 only)
PC Input
Video:15 Pin D Sub Connector
Audio:Minijack
Audio:Minijack
CAM
Conditional Access Module
Input/Output Terminals [SIDE]
Remote control system : Infrared control
Headphone jack
Stereo mini jack
Power requirements
3V dc
2 batteries IEC designation
2 batteries IEC designation
R06 (size AA)
Audio input
Phono jacks
Video input
Phono jack
HDMI input
HDMI Connector
Design and specifications are subject to change without notice.
- 5 -
CONNECTORS
21 Pin Connector (SCART)
_
_
Red input
0.7 +/- 3dB, 75 ohms, positive
_
(S signal Chroma
Connected
Not Connected (open) * at 20Hz - 20kHz
Pin No
1
2
Signal
Signal level
1
Audio output B
(right)
(right)
Standard level : 0.5V rms
Output impedence : Less than 1kohm*
Output impedence : Less than 1kohm*
2
Audio input B
(right)
(right)
Standard level : 0.5V rms
Output impedence : More than 10kohm*
Output impedence : More than 10kohm*
3
Audio output A
(left)
(left)
Standard level : 0.5V rms
Output impedence : Less than 1kohm*
Output impedence : Less than 1kohm*
4
Ground (audio)
5
Ground (blue)
6
Audio input A
(left)
(left)
Standard level : 0.5V rms
Output impedence : More than 10kohm*
Output impedence : More than 10kohm*
7
Blue input
0.7 +/- 3dB, 75 ohms positive
8
Function select
(AV control)
(AV control)
High state (9.5-12V) : Part mode
Low state (0-2V) : TV mode
Input impedence : More than 10K ohms
Input capacitance : Less than 2nF
Low state (0-2V) : TV mode
Input impedence : More than 10K ohms
Input capacitance : Less than 2nF
9
Ground (green)
10
AVlink
11
Green
Green signal : 0.7 +/- 3dB, 75 ohms,
positive
positive
12
Open
13
Ground (red)
14
Ground (blanking)
15
input)
0.3 +/- 3dB, 75 ohms, positive
16
Blanking input
(Ys signal)
(Ys signal)
High state (1-3V) Low state (0-0.4V)
Input impedence : 75 ohms
Input impedence : 75 ohms
17
Ground (video
output)
output)
18
Ground (video
input)
input)
19
Video output
1V +/- 3dB, 75ohms, positive sync 0.3V
(-3+10dB)
(-3+10dB)
20
Video input
1V +/- 3dB, 75ohms, positive sync 0.3V
(-3+10dB)
Video input
Y (S signal)
1V +/- 3dB, 75ohms, positive sync 0.3V
(-3+10dB)
(-3+10dB)
21
Common ground
(plug, shield)
(plug, shield)
- -
- -
19
17
15
13
11
9
7
5
3
1
20
18
16
14
12
10
8
6
4
2
21
How to replace the fuse.
Open the fuse compartment with
a screwdriver blade and replace
the fuse.
Open the fuse compartment with
a screwdriver blade and replace
the fuse.
FUSE
WARNING
(UK Models only)
The flexible mains lead is supplied connected to a B.S. 1363 fused
plug having a fuse of the correct rating for the set. Should the fuse
need to be replaced, use a fuse of the same rating approved by ASTA
to BS 1362, ie one that carries the
plug having a fuse of the correct rating for the set. Should the fuse
need to be replaced, use a fuse of the same rating approved by ASTA
to BS 1362, ie one that carries the
ASA
T
mark.
IF THE PLUG SUPPLIED WITH THIS APPLIANCE IS NOT SUITABLE
FOR THE OUTLET SOCKETS IN YOUR HOME, IT SHOULD BE CUT
OFF AND AN APPROPRIATE PLUG FITTED. THE PLUG SEVERED
FROM THE MAINS LEAD MUST BE DESTROYED AS A PLUG WITH
BARED WIRES IS DANGEROUS IF ENGAGED IN A LIVE SOCKET.
FOR THE OUTLET SOCKETS IN YOUR HOME, IT SHOULD BE CUT
OFF AND AN APPROPRIATE PLUG FITTED. THE PLUG SEVERED
FROM THE MAINS LEAD MUST BE DESTROYED AS A PLUG WITH
BARED WIRES IS DANGEROUS IF ENGAGED IN A LIVE SOCKET.
When an alternative type of plug is used, it should be fitted with the
correct rating fuse, otherwise the circuit should be protected by the
same rating fuse at the distribution board.
correct rating fuse, otherwise the circuit should be protected by the
same rating fuse at the distribution board.
UK PLUG WARNING
- 6 -
HDMI Connector
Rear Connection Panel
Side Connection Panel
15 Pin D Sub Connector (PC)
1
Pin No
Signal Assignment
Pin No
Signal Assignment
1
TMDS Data2+
11
TMDS Clock Shield
2
TMDS Data2 Shield
12
TMDS Clock-
3
TMDS Data2-
13
CEC
4
TMDS Data1+
14
Reserved (N.C. on device)
5
TMDS Data1 Shield
15
SCL
6
TMDS Data1-
16
SDA
7
TMDS Data0+
17
DDC/CEC Ground
8
TMDS Data0 Shield
18
+5V Power
9
TMDS Data0-
19
Hot Plug Detect
10
TMDS Clock+
Pin No
Signal Assignment
Pin No
Signal Assignment
1
Red Out
9
+5V DC
2
Green Out
10
Sync Return (Ground)
3
Blue Out
11
Monitor ID0 in Display
4
Unused
12
DCC Serial Data
5
Ground
13
Horizontal Sync
6
Red Return
14
Vertical Sync
7
Green Return (Ground)
15
DCC Serial Clock
8
Blue Return (Ground)
- 7 -
SE2AG SELF DIAGNOSTIC SOFTWARE
The identification of errors within the SE2AG chassis is triggered in one of two ways :- 1: Busy or 2: Device failure to respond to IIC. In the
event of one of these situations arising the software will first try to release the bus if busy (Failure to do so will report with a continuous
flashing LED) and then communicate with each device in turn to establish if a device is faulty. If a device is found to be faulty the relevant
device number will be displayed through the LED (Series of flashes which must be counted).
event of one of these situations arising the software will first try to release the bus if busy (Failure to do so will report with a continuous
flashing LED) and then communicate with each device in turn to establish if a device is faulty. If a device is found to be faulty the relevant
device number will be displayed through the LED (Series of flashes which must be counted).
LED Error Codes
Number of LED
Flashes
Error Description
Checked
Action
02
Balancer error.
In normal mode.
Goes into standby.
03
DC error.
In normal mode.
Goes into standby.
04
Inverter error.
In normal mode.
Goes into standby.
05
NVM error.
In initialisation state.
Goes into standby.
06
IIC error.
In normal mode.
Goes into standby.
07
HDMI error.
In normal mode.
Adds error to error menu.
08
Digital error.
In normal mode.
Adds error to error menu.
09
Tuner error
In initialisation state.
Adds error to error menu.
10
SP error
In initialisation state.
Adds error to error menu.
13
RTC error
In initialisation state.
Adds error to error menu.
Click on the first or last page to see other KDL-26V4000 / KDL-26V4220 / KDL-26V4230 / KDL-26V4240 / KDL-32V4000 / KDL-32V4200 / KDL-32V4210 / KDL-32V4220 / KDL-32V4230 / KDL-32V4240 / KDL-37V4000 / KDL-37V4220 / KDL-37V4230 / KDL-37V4240 service manuals if exist.