DOWNLOAD Sony KDL-26S5500 Service Manual ↓ Size: 8.09 MB | Pages: 40 in PDF or view online for FREE

To remove the speakers disconnect the speaker wire
harness , remove the one screw circled from the bracket
and ease the complete assy away from the TV set.

Screw

To remove the speakers from the speaker bracket,
remove the 4 screws circled and separate the speaker
from the bracket.

Screw

The procedure is identical for both speakers.

Disconnect the wire harness, release the clip circled and
ease the H2 board away from the TV set.

 Remove the Speakers (See Sec 2-6).

Release the 2 clips indicated and gently pull the bracket
away from the A board in the direction of the arrow.

 

Clip

Clip

Screw Part number(s) and Description(s)

2-580-640-01    SCREW, +BVTP2 4 X 16

4  Screws

Screw Part number(s) and Description(s)

2-580-640-01    SCREW, +BVTP2 4 X 16

1  Screw

To remove the H1 board from the bracket, disconnect the
wire harness, remove the 2 screws circled and lift the board
out of the bracket.

 

Remove the Key Board sub assembly by pushing towards
the panel and lifting out of its guide boss.

Screw Part number(s) and Description(s)

7-685-504-19    SCREW, +BTP 2 X 6

2  Screws

Disconnect the 6 harnesses from the board.  Remove the 9
screws circled. The board can then be carefully lifted from the
TV.

Screw Part number(s) and Description(s)

4-382-854-01    SCREW, +PSW M3 X 8

9  Screws

Disconnect the 3 harnesses from the board. Remove the 6
screws circled and ease the board gently away from the back
of the TV set.

Screw Part number(s) and Description(s)

4-382-854-01    SCREW, +PSW M3 X 8

6  Screws

5

+

(ON SCREEN
 DISPLAY)

(DIGIT 5)

(VOLUME 

+

)

i+

I/

Service adjustments to this model can be performed using the
supplied Remote Commander RM-ED017.

3.

The following menu appears on the screen (See Pic.1).

4.

Move to the corresponding adjustment item using the
‘    ’ or ‘    ’ arrow buttons on the Remote Commander.

5.

Press the ‘      ’ arrow button to enter into the required menu
item.

6.

Adjust the data value using the ‘     ’ or ‘     ’ arrow buttons on
on the Remote Commander.

7.

To go back at any time press the ‘     ’ button on the Remote
Commander.

8.

9.

Press the Red button or ‘Menu’ button on the Remote
Commander to quit the Service Mode when all adjustments
have been completed.

1.

Turn on the power to the TV set.

2.

Press the following sequence of buttons on the Remote
Commander.

The following description shows the items that can be
viewed and/or adjusted using the Service Menu.

•

After carrying out the service adjustments, to prevent the
customer accessing the ‘Service Menu’ switch the TV set
OFF and then ON again.

The following menu appears on the screen when you enter
the ‘Service General Menu’ (See Pic.2). This menu allows
you to view the product information, set the TV into Aging
Mode and perform Software Upgrade to the TV set.

The following menu appears on the screen when you enter
the ‘Service Alignments Menu’ (See Pic.3). This menu
allows adjustment of the TV picture levels. These adjustments
are set during manufacture and should not normally require
further adjustment.

The following menu appears on the screen when you enter
the ‘OSD Service Menu’ (See Pic.4). This menu
allows viewing and adjustment of the AGC and viewing of the
Sound Status.

The following menu appears on the screen when you enter
the ‘Country Selection Menu’ (See Pic.5). Using this menu
the destination country of the TV can be set.

Selection of ‘Reset’ (See Pic.6) allows the TV to be reset to
factory shipping condition. This will restore all settings to those
which were contained in the TV on first shipment.