DOWNLOAD Sony KDL-26S2000 / KDL-32S2000 / KDL-40S2000 Service Manual ↓ Size: 13.17 MB | Pages: 83 in PDF or view online for FREE

After correcting the original service problem, perform the following 
safety checks before releasing the set to the customer:

1.  Check the area of your repair for unsoldered or poorly soldered 

connections. Check the entire board surface for solder splashes and 
bridges.

2.  Check the interboard wiring to ensure that no wires are “pinched” or 

touching high-wattage resistors.

3.  Check that all control knobs, shields, covers, ground straps, and 

mounting hardware have been replaced. Be absolutely certain that 
you have replaced all the insulators.

4.  Look for unauthorized replacement parts, particularly transistors, 

that were installed during a previous repair. Point them out to the 
customer and recommend their replacement.

5.  Look for parts which, though functioning, show obvious signs of 

deterioration. Point them out to the customer and recommend their 
replacement.

6.  Check the line cords for cracks and abrasion. Recommend the 

replacement of any such line cord to the customer.

7.  Check the antenna terminals, metal trim, “metallized” knobs, screws, 

and all other exposed metal parts for AC leakage. Check leakage as 
described below.

The AC leakage from any exposed metal part to earth ground and 
from all exposed metal parts to any exposed metal part having a 
return to chassis, must not exceed 0.5 mA (500 microamperes). 
Leakage current can be measured by any one of three methods.

1.  A commercial leakage tester, such as the Simpson 229 or RCA 

WT-540A. Follow the manufacturers’ instructions to use these 
instructions.

2.  A battery-operated AC milliampmeter. The Data Precision 245 

digital multimeter is suitable for this job.

3.  Measuring the voltage drop across a resistor by means of a VOM 

or battery-operated AC voltmeter. The “limit” indication is 0.75 
V, so analog meters must have an accurate low voltage scale. 
The Simpson’s 250 and Sanwa SH-63TRD are examples of 
passive VOMs that are suitable. Nearly all battery-operated digital 
multimeters that have a 2 VAC range are suitable (see Figure A).

How to Find a Good Earth Ground
A cold-water pipe is a guaranteed earth ground; the cover-plate 
retaining screw on most AC outlet boxes is also at earth ground. If the 
retaining screw is to be used as your earth ground, verify that it is at 
ground by measuring the resistance between it and a cold-water pipe 
with an ohmmeter. The reading should be zero ohms.

If a cold-water pipe is not accessible, connect a 60- to 100-watt 
trouble- light (not a neon lamp) between the hot side of the receptacle 
and the retaining screw. Try both slots, if necessary, to locate the hot 
side on the line; the lamp should light at normal brilliance if the screw 
is at ground potential (see Figure B).

Trouble Light

AC Outlet Box

Ohmmeter

Cold-water Pipe

Figure A. Using an AC voltmeter to check AC leakage.

Figure B. Checking for earth ground.

* Light is green when the TV set is on
* Functions as failure indicator
* Blinks green in aging mode

TIMER LED

Red LED

Lights when timer is set

PIC OFF LED

Green LED

Lights when power saving setting is set to 
picture off (See Instruction Manual)

POWER LED

Red/Green LED

!"

# $

% &

'

(& )

'
&

*

(& $

*
&

# $

# $

+& /

# $

#

;#<%)

# $

# $

;#<%)

#

;<%)

# $

#

;<%)

# $

# $

;<%)

=*>(?

# )

=*>(?@
<%)

#

# )

)%*)A

*>(?#>

<%)#>@

<=B)''#>

#<%)

<%)

*B

;)#>

The units in this manual contain a self-diagnostic function. If an error occurs, the POWER LED will automatically begin to fl ash. The number of times 
the LED fl ashes translates to a probable source of the problem. A defi nition of the POWER LED fl ash indicators is listed in the instruction manual for 
the user’s knowledge and reference. If an error symptom is diffi cult to reproduced use the Remote Commander to display the record that is stored at 
the internal NVM to specify the cause of the failure.

Diagnostic Test Indicators
When an error occurs, the POWER LED will fl ash a set number of times to indicate the possible cause of the problem. If there is more than one error, 
the LED will identify the fi rst of the problem areas. If the errors occur simultaneously, the one that corresponds to the fewest fl ashes is identifi ed fi rst.
Results for all of the following diagnostic items are displayed on screen.  No error has occurred if the screen displays a “0”.

;)#>(&

% <

C

**BE +>=*#)G/

J

*>ME@*NEE +>=*#)J/

G

*E +>=*#)C/

O

(& '

M

*%E

P

*&E

Q

< ) + /

R

<=MUUU

2 Screws, +PSW M4X16
(KDL-26S2000/32S2000 ONLY) 
4 Screws, +PSW M5X16
(KDL-40S2000 ONLY)

2

2

1

 

2 Screws, +PSW M4X16 

(KDL-26S2000 ONLY)
 2 Screws, +PSW M6X16 
(KDL-32S2000/40S2000 ONLY)

4

 Lift to remove Rear Cover

7

 

4 Screws

+BVTP2 4X16

 

4 Screws

+BVTP2 4X16

1

5

 

1 Screw

+BVTP2 4X12

(KDL-26S2000 ONLY)

 1 Screw, +BVTP2 4X16

(KDL-32S2000/40S2000 ONLY)

2

 

1 Screw

+BVTP2 4X12
(KDL-26S2000 ONLY)
 1 Screw, +BVTP2 4X16
(KDL-32S2000/40S2000 ONLY)

6

 

2 Screws

+BVTP 3X12 TYPE2 IT-3

3

☛

☛