Sony KDL-22E5300 / KDL-22E5310 Service Manual ▷ View online
- 4 -
CAUTION
1. Lamp Caution - Wire Dressing.
NG
OK
During assembly please ensure that the
lamp wires are placed inside the panel area.
lamp wires are placed inside the panel area.
2. Lamp Caution - Twisted Wires.
NG
OK
When connecting the lamp wires
please ensure that they are not
twisted.
please ensure that they are not
twisted.
3. Lamp Caution - Disconnecting.
NG
OK
When disconnecting please do not
pull the wires. Please disconnect by
pulling the connector lock.
pull the wires. Please disconnect by
pulling the connector lock.
- 5 -
SPECIFICATIONS
System
Panel system
LCD (Liquid Crystal Display) Panel
TV system
Analogue: Depending on your country/area selection: B/G/H, D/K, L, I
Digital: DVB-T/DVB-C
Digital: DVB-T/DVB-C
Colour/video system
Analogue: PAL, PAL60 (only video input), SECAM, NTSC3.58, NTSC4.43 (only video input)
Digital: MPEG-2 MP@ML/HL, H.264/MPEG-4 AVC MP/HP@L4
Digital: MPEG-2 MP@ML/HL, H.264/MPEG-4 AVC MP/HP@L4
Channel coverage
Analogue: VHF: E2–E12/UHF: E21–E69/CATV: S1–S20/HYPER: S21–S41
D/K: R1–R12, R21–R69/L: F2–F10, B–Q, F21–F69/I: UHF B21–B69
Digital: VHF/UHF
D/K: R1–R12, R21–R69/L: F2–F10, B–Q, F21–F69/I: UHF B21–B69
Digital: VHF/UHF
Sound output
5 W + 5 W
Input/Output jacks
Aerial/Antenna cable
75 ohm external terminal for VHF/UHF
/
AV1
21-pin scart connector (CENELEC standard) including audio/video input, RGB input and TV audio/video
output.
output.
/
/
AV2
21-pin scart connector (CENELEC standard) including audio/video input, RGB input and selectable audio/
video output.
video output.
COMPONENT IN
Supported formats: 1080p, 1080i, 720p, 576p, 576i, 480p, 480i
Y: 1 Vp-p, 75 ohms, 0.3V negative sync/P
Y: 1 Vp-p, 75 ohms, 0.3V negative sync/P
B
/C
B
: 0.7 Vp-p, 75 ohms/
P
R
/C
R
: 0.7 Vp-p, 75 ohms
COMPONENT IN
Audio input (phono jacks)
HDMI IN1, 2, 3, 4
Video: 1080/24p, 1080p, 1080i, 720p, 576p, 576i, 480p, 480i
Audio: Two channel linear PCM: 32, 44.1 and 48 kHz, 16, 20 and 24 bits, Dolby Digital
Analogue audio input (minijack) (HDMI IN1 only)
PC Input (Page 6)
Audio: Two channel linear PCM: 32, 44.1 and 48 kHz, 16, 20 and 24 bits, Dolby Digital
Analogue audio input (minijack) (HDMI IN1 only)
PC Input (Page 6)
AV3
Video input (phono jack)
AV3
Audio input (phono jacks)
DIGITAL AUDIO
OUT (OPTICAL)
Digital optical jack (Two channel linear PCM, Dolby Digital)
Audio output (phono jacks)
PC IN
PC Input (D-sub 15-pin) (Page 6)
G: 0.7 Vp-p, 75 ohms, non Sync on Green/B: 0.7 Vp-p, 75 ohms/
R: 0.7 Vp-p, 75 ohms/HD: 1-5 Vp-p/VD: 1-5 Vp-p
G: 0.7 Vp-p, 75 ohms, non Sync on Green/B: 0.7 Vp-p, 75 ohms/
R: 0.7 Vp-p, 75 ohms/HD: 1-5 Vp-p/VD: 1-5 Vp-p
PC audio input (minijack)
USB port
i
Headphones jack
CAM (Conditional Access Module) slot
LAN
10BASE-T/100BASE-TX connector (Depending on the operating environment of the network, connection
speed may differ. 10BASE-T/100BASE-TX communication rate and communication quality are not
guaranteed for this TV.)
speed may differ. 10BASE-T/100BASE-TX communication rate and communication quality are not
guaranteed for this TV.)
- 6 -
*Specified standby power is reached after the TV finishes necessary internal processes.
Design and specifications are subject to change without notice.
PC input signal reference chart for
PC and HDMI IN 1, 2, 3, 4
• This TV’s PC input does not support Sync on Green or Composite Sync.
• This TV’s PC input does not support interlaced signals.
• For the best picture quality, it is recommended to use the signals in the above chart with a 60 Hz vertical
• This TV’s PC input does not support interlaced signals.
• For the best picture quality, it is recommended to use the signals in the above chart with a 60 Hz vertical
frequency (boldfaced).
Power and others
Power requirements
220 V – 240 V AC, 50 Hz
Screen size (measured
diagonally)
diagonally)
22 inches / Approx. 55 cm
Display resolution
1,366 dots (horizontal) × 768 lines (vertical)
Power
consumption
consumption
in “Home”/
“Standard”
mode
“Standard”
mode
37 W
in “Shop”/
“Vivid”
mode
“Vivid”
mode
45 W
Standby power
consumption*
consumption*
0.37 W (17 W when “Quick Start” is set to “On”)
Dimensions (Approx.) (w × h × d)
with Table-Top Stand
58.6 x 39.8 x 15.6 cm
without Table-Top Stand
58.6 x 37.8 x 9.0 cm
Mass (Approx.)
with Table-Top Stand
7.0 kg
without Table-Top Stand
6.5 kg
Resolution
Horizontal
frequency (kHz)
frequency (kHz)
Vertical
frequency (Hz)
frequency (Hz)
Standard
Signals
Horizontal
(Pixel)
(Pixel)
× Vertical
(Line)
VGA
640
×
480
31.5
60
VESA
640
×
480
37.5
75
VESA
720
×
400
31.5
70
VESA
SVGA
800
×
600
37.9
60
VESA
800
×
600
46.9
75
VESA
XGA
1024
×
768
48.4
60
VESA
1024
×
768
56.5
70
VESA
1024
×
768
60.0
75
VESA
WXGA
1280
×
720
45.0
60
EIA
1280
×
768
47.4
60
VESA
1280
×
768
47.8
60
VESA
1360
×
768
47.7
60
VESA
- -
CONNECTORS
Pin Connector (SCART)
HDMI Connector
5 Pin D Sub Connector (PC)
Pin No
AV-1
AV-2
Signal
Signal Level
1
•
•
Audio Output B
(Right)
(Right)
Standard Level: 0.5V rms
Impedance: less than 1K
Impedance: less than 1K
Ω*
2
•
•
Audio Input B
(Right)
(Right)
Standard Level: 0.5V rms
Impedance: more than 10K
Impedance: more than 10K
Ω*
3
•
•
Audio Output A
(Left)
(Left)
Standard Level: 0.5V rms
Impedance: less than 1K
Impedance: less than 1K
Ω*
4
•
•
Ground (Audio)
5
•
•
Ground (Blue)
6
•
•
Audio Input A (Left)
Standard Level: 0.5V rms
Impedance: more than 10K
Impedance: more than 10K
Ω*
7
•
•
Blue Input
0.7V +/- 3dB, 75
Ω, positive
8
•
•
Function Select
(AV control)
(AV control)
High State (9.5~12V): AV mode
Low State (0~2V): TV mode
Impedance: more than 10K
Low State (0~2V): TV mode
Impedance: more than 10K
Ω*
Capacitance: less than 2nF
9
•
•
Ground (Green)
10
-
•
AV Link
11
•
•
Green Input
0.7V +/- 3dB, 75
Ω, positive
12
-
•
Open
13
•
•
Ground (Red)
14
•
•
Ground (Blanking)
15
•
•
Red Input
0.7V +/- 3dB, 75
Ω, positive
•
•
S signal Chroma Input
0.3V +/-3dB, 75
Ω, positive
16
•
•
Blanking Input
(Y Signal)
(Y Signal)
High State (1~3V)
Low State (0~0.4V)
Impedance: 75
Low State (0~0.4V)
Impedance: 75
Ω
17
•
•
Ground
(Video Output)
(Video Output)
18
•
•
Ground
(Video Input)
(Video Input)
19
•
•
Video Output
1V +/-3dB, positive sync 0.3V (-3+10dB)
20
•
•
Video Input
1V +/-3dB, positive sync 0.3V (-3+10dB)
•
•
Video Input Y
(S Signal)
(S Signal)
1V +/-3dB, positive sync 0.3V (-3+10dB)
21
•
•
Common Ground
(Shield)
(Shield)
1
3
5
7
9
11
13
15
17
19
21
2
4
6
8
10
12
14
16
18
20
19
17
15
13
11
9
7
5
3
1
18
16
14
12
10
8
6
4
2
5
4
3
2
1
10
9
8
7
6
15
14
13
12
11
Pin No
Signal Assignment
Pin No
Signal Assignment
Pin No
Signal Assignment
1
Red Output
6
Red Return
11
Monitor IDO in display
2
Green Output
7
Green Return (Ground)
12
DCC Serial Data
3
Blue Output
8
Blue Return (Ground)
13
Horizontal Sync
4
Unused
9
+5V DC
14
Vertical Sync
5
Ground
10
Sync Return (Ground)
15
DCC Serial Clock
Pin No
Signal Assignment
Pin No
Signal Assignment
1
TMDS Data2+
11
TDMS Clock Shield
2
TMDS Data2 Shield
12
TMDS Clock-
3
TMDS Data2-
13
CEC
4
TMDS Data1+
14
Reserved (N.C. on device)
5
TMDS Data1 Shield
15
SCL
6
TMDS Data1-
16
SDA
7
TMDS Data0+
17
DDC/CEC Ground
8
TMDS Data0 Shield
18
+5V power
9
TMDS Data0-
19
Hot Plug Detect
10
TMDS Clock+
Click on the first or last page to see other KDL-22E5300 / KDL-22E5310 service manuals if exist.