Sony KD-49X8505B / KD-55X8505B / KD-55X9005B / KD-65S9005B / KD-65X8505B / KD-65X9005B / KD-65X9505B / KD-70X8505B / KD-75S9005B / KD-79X9005B / KD-85X9505B / KDL-32W705B / KDL-32W705C / KDL-32W706B / KDL-40W605B / KDL-40W705C / KDL-42W705B / KDL-42W706B / KDL Service Manual ▷ View online
RB2G / RB2T
CHASSIS
Some user setting may have
changed during the update.
Please remove the USB device and
select ""OK to exit.
Status 1
Status 2
Remove
Remove
1) Replace a panel module (Refer to each segment Service Manual for
Board (Tcon, Driver/ Converter & Panel) details).
2) After AC Plug-in(AC On), wait for 20s then turn on TV by power key on
TV or Remote Commander.
Note : Important: 20s wait is necessary for
successful SW writing in Task [3].
b) When you turn on the TV after replacing Panel , there will be two
cases depend on the PANEL ID setting. Below are the example:
cases depend on the PANEL ID setting. Below are the example:
3)
Software update by USB memory. (refer to section 1.3 Preparing USB for
Upgrade)
i) Remove all signal connection.(antenna, external input, ether cable, etc)
ii) Insert the USB memory.
Upgrade)
i) Remove all signal connection.(antenna, external input, ether cable, etc)
ii) Insert the USB memory.
iii) If older software package version is used, smart core amber and
green LED will remain blinking. (Software can not update).
green LED will remain blinking. (Software can not update).
iv) If valid file found, below message will appear. TV will reboot in a
minute after the USB device is inserted, then the Red LED lights and the
Amber LED blinks
minute after the USB device is inserted, then the Red LED lights and the
Amber LED blinks
13
SERVICE PROCEDURE
( PANEL)
( PANEL)
SERVICE PROCEDURE (PANEL)
SECTION 3
i) Panel : No Picture- SMART CORE LED :
Amber & Green blinking
Amber & Green blinking
ii) Panel : Picture appear
SMART CORE LED : White Lit
SMART CORE LED : White Lit
4) TV on standby. Enter Service Mode. Press “i+ (info)”, “5”, “Volume +” then “TV
power” on remote.
Note : a) <Restriction>When TV power status is "Deep STBY Mode", you
cannot enter Service Mode due to not receive the above SIRCS command.
cannot enter Service Mode due to not receive the above SIRCS command.
b) <Operation method> (To enter this mode surely.)
After TV goes to STBY status by Remote commander, Please input the
sequence (four keys described above) by RC within 15 seconds (UC) or 1
minute (Other Destination).
sequence (four keys described above) by RC within 15 seconds (UC) or 1
minute (Other Destination).
3-1. Service Procedure for Panel Module replacement.
Note :
Black font : Procedure/ Step
Red font : Caution ( Additional Info).
Blue font: Additional Info.
Black font : Procedure/ Step
Red font : Caution ( Additional Info).
Blue font: Additional Info.
Preparing for software update.
During the system update, the TV
will automatically restart.
Please do not disconnect the power or
remove the USB device, until update
is completed.
The update may take up to 5 minutes.
Copying update file from USB.
Please wait...
v) Status 1: Please wait awhile, until the SMART CORE LED will change to white blinking
then TV goes to Standby (Software update complete). Turn on TV. OR
then TV goes to Standby (Software update complete). Turn on TV. OR
v) Status 2: After SW completes, TV will reboot itself and message will appear to
indicate SW update complete/
indicate SW update complete/
RB2G / RB2T
CHASSIS
14
SERVICE PROCEDURE
( PANEL)
( PANEL)
5. Press “OPTIONS” on remote. In “VPC” service mode (For HT only)
a.Select “001 DATA_BACKUP” category by pressing “2 / 5” on remote.
b.Change data from “0” to “1” by pressing “3 / 6” on remote.
c.Wait until data is changed from 1 to 3.
d.When data is changed from 1 to 3, restoring process is finished.
e.In case data is changed from 1 to 2, restoring process is failure
[this function not support].
b.Change data from “0” to “1” by pressing “3 / 6” on remote.
c.Wait until data is changed from 1 to 3.
d.When data is changed from 1 to 3, restoring process is finished.
e.In case data is changed from 1 to 2, restoring process is failure
[this function not support].
Remote Commander
a
b
End restore process
VPC
SERVICE
002
DATA_INIT
000
WB_INIT
3
DATA TRANSFER SUCCESS
Restore process
VPC
SERVICE
002
DATA_INIT
000
WB_INIT
1
DO NOT POWER OFF
DO NOT TOUCH ANY KEY NOW
DO NOT TOUCH ANY KEY NOW
OPTIONS
Reference Table
6. Press “OPTIONS” on remote. In “VPC” service mode
(For HE, HM, XML, XMAL, XML2)
a.Select “
“
002 DATA_INIT” category by pressing “2 / 5” on remote.
b.Change data from “0” to “1” by pressing “3 / 6” on remote.
c.Wait until data is changed from 1 to 3.
d.When data is changed from 1 to 3, restoring process is finished.
e.In case data is changed from 1 to 2, restoring process is failure.
c.Wait until data is changed from 1 to 3.
d.When data is changed from 1 to 3, restoring process is finished.
e.In case data is changed from 1 to 2, restoring process is failure.
Remote Commander
a
b
End restore process
VPC
SERVICE
001
DATA_BACKUP
000
BU_FLASH
3
DATA TRANSFER SUCCESS
Restore process
VPC
SERVICE
001
DATA_BACKUP
000
BU_FLASH
1
DO NOT POWER OFF
DO NOT TOUCH ANY KEY NOW
DO NOT TOUCH ANY KEY NOW
OPTIONS
Seg.
Model Name
HE
KDL-** W700B, W705B, W706B, W707B, W708B, W790B, W800B, W805B, W807B,
W808B, W815B, W817B, W828B, W829B, W840B, W850B, W855B, W856B, W857B
W808B, W815B, W817B, W828B, W829B, W840B, W850B, W855B, W856B, W857B
HM
KDL**W580B, W585B, W590B, W600B, W605B, W607B, W608B, W609B, W610B,
W630B, WM15B
W630B, WM15B
XML
KDL-**W700C, W705C, KJ-**W700C
XMAL
KDL-**W780C
XML2
KJ-**W730C
Seg.
Model Name
HT
KDL-** W900B, W950B, W955B, W957B
Reference Table
RB2G / RB2T
CHASSIS
15
SERVICE PROCEDURE
( PANEL)
( PANEL)
7. Press “OPTIONS” on remote. In “VPC” service mode (For HX, HJ, HA, HC)
a.Select “006 PANEL” category by pressing “2 / 5” on remote.
b.Change data from “0” to “1” by pressing “3 / 6” on remote.
c.Wait until data is changed from 1 to 2.
d.When data is changed from 1 to 2, restoring process is finished.
e.In case data is changed from 1 to 3, restoring process is failure
[this function not support].
b.Change data from “0” to “1” by pressing “3 / 6” on remote.
c.Wait until data is changed from 1 to 2.
d.When data is changed from 1 to 2, restoring process is finished.
e.In case data is changed from 1 to 3, restoring process is failure
[this function not support].
Remote Commander
a
b
End restore process
VPC
SERVICE
006
PANEL
000
RECOVERY
2
DATA TRANSFER SUCCESS
Restore process
VPC
SERVICE
006
PANEL
000
RECOVERY
1
DO NOT POWER OFF
DO NOT TOUCH ANY KEY NOW
DO NOT TOUCH ANY KEY NOW
OPTIONS
Reference Table
Seg.
Model Name
HX
XBR-** X950B, X955B, X957B, KD-** X9500B, X9505B
HJ
XBR-** X900B, X905B, X907B, KD-** X9000B, X9005B, X9200B
HA
XBR-** X850B, X855B, X857B, KDL-** X830B, KD-** X8000B, X8500B, X8505B
HC
KD-**S9000B, S9005B
RB2G / RB2T
CHASSIS
16
SERVICE PROCEDURE
( PANEL)
( PANEL)
8. After completing all the service adjustment changes, verify that the correct
Model ID and Product ID displays in the Service menu.
Model ID and Product ID displays in the Service menu.
a.Press the OPTIONS key to go to the Digital Service menu.
(There are 3 Service menus “DIGITAL”
(There are 3 Service menus “DIGITAL”
“CHASSIS” “VPC”)
b.Verify the Software version, Model ID and Product ID are the
correct
correct
Remote Commander
OPTIONS
Digital Service menu
9. Reset Panel Operation Time.
a. Go to TV standby condition by remote commander.
b. Press “i+ (info)”, “5”, “Volume-” then “TV power” on remote.
c. You can see Self Diagnosis Display.
a. Go to TV standby condition by remote commander.
b. Press “i+ (info)”, “5”, “Volume-” then “TV power” on remote.
c. You can see Self Diagnosis Display.
d. Reset Panel Operation Time . Press <7> + <0> on remote.
Diagnosis Display (Sample)
8. The upgrade process is complete and unplug the AC cord.
Please refer to Appendix pages to verify the Model ID and Product ID.
Model ID
Product
ID
Software
Package
Version
Package
Version
DIGITAL SERVICE
001 OP
000 VERS ---
<MAIN> <EXT>
DM1.301W00AA WF:2.0.0.99
WF1.003W00AA WF:--------
DF1.001W00AA FD:0.068
YM1.010W00AA BT:
M4.922C
1.2.14.891
(DM1.301W00AA)
DD1.016W00AA EFR:10.00.13.01
PK0.312W00AA
AM0.510WW
MID:04835511
PID:04020000
PNL:LTY320AB01
DQ3Y550LN0101
`
Panel Operation Time
SELF CHECK
002 MAIN_POWE ------------ ------------ 00 Model Name : KDL-50W800B
003 AFE_I2C ------------ ------------ 00 Serial Number : 1000008
003 DC_ALERT ------------ ------------ 00 Package Number : PKG0.270EUA
003 AUD_ERR ------------ ------------ 00 Device ID : B0:00:01:EF:4B:C6
003 HDMI_EQ ------------ ------------ 00 Wired MAC : D8:D4:3C:17:84:3E
003 TU_DEMOD ------------ ------------ 00 Wireless MAC : N/A
003 AFE_SPI ------------ ------------ 00 USB dongle : N/A
004 VLED ------------ ------------ 00
004 LD_ERR ------------ ------------ 00 <MAIN> <EXT>
005 TCON_ERR 120823132523 ------------ 01 DM0.270EUA WF:3.5.3.99
005 P_ID_ERR ------------ ------------ 00 WF0.190W0AA WF:--------
005 FRCTC_I2C ------------ ------------ 00 DF5.091W00AA FD:-.---
006 BACKLIGHT ------------ ------------ 00 YM1.212W00AA BT:2.1.14.413
007 TEMP_ERR ------------ ------------ 00 M5.426C
007 FAN_ERR ------------ ------------ 00 (DM0.270EUA) EFR : -----------
008 VPC_WDT ------------ ------------ 00 DD0.181W00AA
008 MEPS_WDT ------------ ------------ 00 PK0.181W00AA
008 HOST_WDT ------------ ------------ 00 AM0.270WW
008 STBY_WDT ------------ ------------ 00
008 AFE_WDT ------------ ------------ 00 MID:2A11A30E
009 TU_BOARD ------------ ------------ 00 PID:0E048040
PNL:LC550EUF-FGF1
00021-10573-00025 0000000000000600-0000000000000000
Click on the first or last page to see other KD-49X8505B / KD-55X8505B / KD-55X9005B / KD-65S9005B / KD-65X8505B / KD-65X9005B / KD-65X9505B / KD-70X8505B / KD-75S9005B / KD-79X9005B / KD-85X9505B / KDL-32W705B / KDL-32W705C / KDL-32W706B / KDL-40W605B / KDL-40W705C / KDL-42W705B / KDL-42W706B / KDL service manuals if exist.