DOWNLOAD Sony BG2T Service Manual ↓ Size: 2.92 MB | Pages: 49 in PDF or view online for FREE

– 9 –

If the picture or sound is abnormal when receiving programs through the 8 (antenna
input) terminal

(1) Press SELECT until “TV SYS” appears on the screen.

(2) Press + or – to select the appropriate TV system until the picture or sound quality

is optimal.

If the color is abnormal when receiving programs through the 8 (antenna input)
terminal or the t (video input) terminal.

(1) Press SELECT until “COLOR SYS” appears on the screen.

(2) Press + or – to select the appropriate color system until the color is optimal.

Note
• The color system “SECAM” is available for KV-TG21M40 only.

(1) Press PROGR +/– or the number buttons until the unused or unwanted program

number appears on the screen.

(2) Press SELECT until “MANUAL PROGRAM” appears on the screen.

(3) Press + or – once to enter the “MANUAL PROGRAM” mode.

(4) Press PIC MODE to skip the unused or unwanted program number.

(5) Press SELECT to exit the “MANUAL PROGRAM” mode.

Note
• To restore the skipped program number again,  preset the channel automatically or manually.

The fine tuning (FINE) function may help to reduce the following problems:
double images and lines moving across the TV screen.

You can use the fine tuning function as below:

(1) Select the program number you want to adjust.

(2) Press SELECT until “MANUAL PROGRAM” appears on the screen.

(3) Press + or – once to enter the “MANUAL PROGRAM” mode.

(4) Press   to display “FINE” on the screen.

(5) Press + or – continuously until the above problems are minimized.

The + or – icon on the screen flashes while tuning.

(6) Press SELECT to exit the “MANUAL PROGRAM” mode.

J Presetting channels

You can automatically preset up to 100 TV channels in numerical sequence
from program number 1, or manually preset desired channels and channels
that cannot be preset automatically.

Press SELECT until “AUTO PROGRAM” appears
on the screen.

Press + or – once to enter the “AUTO
PROGRAM” mode.

The on-screen display will start flashing.

Press PROGR +/– or the number buttons until
the desired program number appears on the
screen.

Press + or – to start presetting channels
automatically.

Press SELECT until “MANUAL PROGRAM”
appears on the screen.

Press + or – once to enter the “MANUAL
PROGRAM” mode.

Press PROGR +/– or the number buttons until
the desired program number appears on the
screen.

Press + or – until the desired channel picture
appears on the screen.

To preset other channels manually, repeat steps
3 to 4.

TV

1

2

3

4

6

7

8

9

-

0

5

JUMP

SOUND 

MODE

 

FAVORITE

PROGR

2

K

You can customize the picture by selecting the picture mode or by adjusting its
settings.

  Press PIC MODE to select the desired picture mode.

“DYNAMIC”

view high contrast pictures.

“STANDARD”

view normal contrast pictures.

“SOFT”

view mild pictures.

  

Press SELECT until the desired setting appears.

Each time you press SELECT, the setting item will
change as follows:

Press + or – to adjust the item.

To adjust other items, repeat steps 1 to 2.

Notes
• “HUE” can be adjusted for the NTSC color system only.
• Reducing “SHARP” can also reduce picture noise.

TV

1

2

3

4

6

7

8

9

-

0

5

JUMP

SOUND 

MODE

 

FAVORITE

PROGR

2

–

 10 

–

1 Eight screws

(+BVTP 4 

× 16)

1 Rear Cover

1 Four screws 

(BVTP 3 

× 12)     

CRT SUPPORT BLOCK

1 Four screws 

(BVTP 3 

× 12)     

Push claw

 Do not take out CRT support block while TV set in

standing position.

 Undress necessary wires that creates tension while

placing the chassis into Service Position.

1 One screw

(+BVTP 4 

× 16)

2 Terminal Bracket

–

 11 

–

•

Please make sure the TV set is not in standing position before removing necessary
CRT support located on bottom right and left.

One screw
(+BVTP 3 

× 12)

1

Push to direction of arrow 
and remove

7

Demagnetic coil

!º

Two screws
(Tapping 5+
Crown Washer)

Tension
spring

9

Chassis assy

5 Deflection

yoke

6

CV board

2

Anode
cap

3

Coating earth assy

!£

Picture tube

1 Cushion

!¡

Two screws
(Tapping 5 +
Crown Washer) 

8

Holder DGC

6

PWB Bracket

!™

CRT Support Block

!™

 CRT Support Block

Screw Location

Beznet Hook

4

For replacements of light guide,unscrew them,
exchange with new parts and fix them with
screws respectively.

–

 12 

–

•REMOVAL OF ANODE-CAP

NOTE : After removing the anode, short circuit the anode of the picture tube and

the anode cap to the metal chassis, CRT shield or carbon paint on the
CRT.

•REMOVING PROCEDURES

1 Turn up one side of the rubber cap in the direction indicated by the arrow a.

2 Using a thumb pull up the rubber cap firmly in the direction indicated by the arrow b.

3 When one side of the rubber cap is separated from the anode button,  the anode-cap

can be removed by turning up the rubber cap and pulling it up in the direction of the
arrow c.

• HOW TO HANDLE AN ANODE-CAP

1 Do not damage the surface of anode-caps with sharp shaped objects.
2 Do not press the rubber too hard so as not to damage the inside of anode-cap.

3 Do not turn the foot of rubber over too hard.

a

a

b

b

Anode button

c