DOWNLOAD Sony VPL-HS10 / VPLL-CT10 / VPLL-CW10 Service Manual ↓ Size: 13.58 MB | Pages: 123 in PDF or view online for FREE

Model
VPL-HS10 VPLL-CT10 VPLL-CW10
Pages
123
Size
13.58 MB
Type
PDF
Document
Service Manual
Brand
Device
Projector / REVISED-1
File
vpl-hs10-vpll-ct10-vpll-cw10.pdf
Date
PREV: Sony RM-PJVW10 / VPL-VW12HT (serv.man2) Service Manual

Sony VPL-HS10 / VPLL-CT10 / VPLL-CW10 Service Manual ▷ View online

2-7
VPL-HS10
Channel Memory
Memory Name
Video 1
S Video 1
Input-A
Video 2
S Video 2
Component
Digital
MS
Image Flip Memory
Remarks
Turn over to the upper 
and lower sides
No turn over to the 
upper and lower sides
Adjustment is 
impossible
Adjustment is 
impossible
Adjustment is 
impossible
Adjustment is 
impossible
Adjustment is 
impossible
Adjustment is 
impossible
Adjustment is 
impossible
Adjustment is 
impossible
Adjustment is 
impossible
Adjustment is 
impossible
Adjustment is 
impossible
Adjustment is 
impossible
2-8
VPL-HS10
3) LOW Mode of INPUT-A
1.
Input the 80 IRE FLAT FIELD signal to INPUT-A.
2.
Set the GAIN R that is equal to MID mode value. (Set
the GAIN R to the same as MID mode value.)
3.
Set the BIAS R, G and B that are equal to MID mode
value. (Set the BIAS R, G and B to the same as MID
mode value).
4.
Input the 30 IRE signal to INPUT-A.
5.
Adjust the chromaticity (x at 0.313, y at 0.329) values
by the BIAS R and B of W/B LOW mode.
6.
Input the 80 IRE signal to INPUT-A.
7.
Adjust the chromaticity (x at 0.313, y at 0.329) values
by the GAIN G and B.
8.
Repeat above steps 4 to 7 until the chromaticity
become the following values.
x: 0.313
± 0.002, y: 0.329± 0.004
4) MID/HIGH/LOW Mode of VIDEO
1.
Input the VIDEO signal of NTSC or PAL.
2.
Set the BIAS R, G and B and GAIN R, G and B of
MID, HIGH and LOW mode of W/B that are equal to
the values of corresponding items in INPUT-A.
(Altogether 18 items)
3.
Set the GAIN G only of MID mode of W/B value at
“
_16” in INPUT-A.
2-5. Tilt Adjustment
n
Do not put the unit upward and downward in the vertical
direction for more than ten seconds.
1.
Set the Factory mode to “Device Adjust/OTHER”.
2.
Set the adjuster in contracted position.
3.
Then, enter the X TILT value to C0.
4.
Set the unit upward in vertically.
5.
Then, enter the X TILT value to C1.
6.
Set the unit downward in vertically.
7.
Then, enter the X TILT value to C2.
8.
Save the each values of C0, C1 and C2 described in
step3, 5 and 7.
2-4. White Balance Adjustment on
Servicing
2-4-1. White Balance Adjustment
Input the 10 STEP signal to INPUT-A, and observe the
chromaticity of each luminance.
When varying the chromaticity of each luminance, perform
the following adjustments.
1) MID Mode of INPUT-A
1.
Input the 100 IRE FLAT FIELD signal to INPUT-A.
2.
Measure the chromaticity (x, y).
3.
Input the 80 IRE FLAT FIELD signal to INPUT-A.
4.
Adjust the chromaticity (x, y) to the values measured
in step 2, by the GAIN R and B of W/B MID mode.
5.
Set the INPUT signal to the 30 IRE FLAT FIELD
signal.
6.
Adjust the chromaticity (x, y) to the values measured
in step 2, by the BIAS R and B.
7.
Repeat above steps 3 to 6 until the chromaticity
become the following values.
x 
± 0.002, y ± 0.004 (The x and y are the values
measured in step 2.)
2) HIGH Mode of INPUT-A
1.
Input the 80 IRE FLAT FIELD signal to INPUT-A.
2.
Set the GAIN G to MID mode value at “
_20” with the
HIGH mode of the W/B.
3.
Set the BIAS R, G and B that are equal to MID mode
values. (Set the BIAS R, G and B to the same as MID
mode values.)
4.
Input the 30 IRE signal to INPUT-A.
5.
Adjust the chromaticity (x at 0.284, y at 0.298) values
by the BIAS R and B of W/B HIGH mode.
6.
Input the 80 IRE signal to INPUT-A.
7.
Adjust the chromaticity (x at 0.284, y at 0.298) values
by the GAIN R and B.
8.
Repeat above steps 4. to 7. until the chromaticity
become the following values.
x: 0.284
± 0.002, y: 0.298± 0.004
3-1
VPL-HS10
74VHC02MTCX
SN74LV00APWR
SN74LV04APWR
ADXL202JE-REEL
Section 3
Semiconductors
IC
AK4352VT-E2
CY27027ZCT
LT1399CGN
SN74LV4052APWR
SN74LV4053APWR
TPA2000D1PW
BA6286N
HD64F2377VFQ33V
2
3
1
ISPLSI2032VE-110LT44A-51GB
LP2985IM5X-3.3
S-80928ANMP-DDR-T2
SN74AHC1G00DCKR
TC4W53FU
TC4W53FU(TE12R)
TC7S66FU
TC7S66FU(TE85R)
TC7SET04FU(TE85R)
TC7SZ125FU(TE85R)
LMC7101BIM5X
1
7
3
5
BOTTOM VIEW
BA033FP-E2
BA05FP-E2
BA12FP-E2
BA00ASFP-E2
MARKING SIDE VIEW
1
10PIN SIP
CXD9671GG
1
A
INDEX
BOTTOM VIEW
176PIN BGA
HY57V161610DTC-7TR
1
TOP VIEW
50PIN TSOP
IRMF-A0T-QTP
TK11900MTL
1
TOP VIEW
1
TOP VIEW
144PIN QFP
1
TOP VIEW
44PIN QFP
L88M05T-FA-TL
LM1117MPX-1.8
NJM78M09DL1A(TE1)
1 2
3
1 2
3 4
5
24LC21AT/SN
HN58X24256FPIZ
ICS332-SX1745
M24C02-WMN6T(A)
M24C64-WMN6T(B)
MAX1626ESA-TE2
MM1096AFF
MM1228XFBE
SN74LV08APWR
SN75157PS-ELL20
SN75157PS-ELL2000
ST24FC21M6TR
TA75W393FU
TA75W393FU-TE12R
TL431BCDR2
1
2
3
4
5
5PIN CHIP
1
TOP VIEW
8PIN SOP
1
TOP VIEW
16PIN SOP
1
TOP VIEW
14PIN SOP
3-2
VPL-HS10
IC
SAA7118E/V1.518
ST72T631K4M1-201
RS-140-T
1
2
3
4
1
TOP VIEW
34PIN SOP
PW265-10T
1
A
BOTTOM VIEW
256PIN BGA
UPD64083GF-3BA
1
TOP VIEW
100PIN QFP
1
A
BOTTOM VIEW
156PIN BGA
TDA7309D013TR
MT48LC8M16A2TG-75-Y95WT
1
TOP VIEW
MX29LV800TTC-70G-SX1745
1
24
48
25
TOP VIEW
MZ1540
MARKING SIDE VIEW
1
PQ20VZ1U
1: DC IN
2: ON/OFF CTL
3: DC OUT
4: DC OUT ADJ
5: GND
1
3
2
5
4
PQ2TZ15U
5
1
1
TOP VIEW
20PIN DIP
M52347FP-TE
SN74LV125APWR
SN74LV244APWR
SN74LV541APWR
MB93401A
MB93491
1
TOP VIEW
176PIN QFP
1
TOP VIEW
20PIN SOP
M62392FP
1
TOP VIEW
24PIN SOP
MCZ3001D
1
A
BOTTOM VIEW
288PIN BGA
1
TOP VIEW
18PIN DIP
54PIN TSOP
48PIN TSOP
Page of 123
Display

Click on the first or last page to see other VPL-HS10 / VPLL-CT10 / VPLL-CW10 service manuals if exist.

RANDOM: